0622018961

Impel Daughtercard Press-In Tool Impel Daughtercard Module Installation Press-In Tool Application Tooling Specification Sheet Order No. 62201-8961 FEATURES Lip provided for positive alignment to connector assembly. Tool provides uniform distribution of press force across entire pin array. May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools. SCOPE Products: Impel 2.35mm Orthogonal Daughtercard Assembly, Orthogonal Direct RAM Assembly, and standard RAM Assembly (6-Pair by 12 Column Assemblies). See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. Series No. Guide Style Columns Unguided 12 171500-1022 171500-3022 Left 12 171500 171500-3622 171500-5022 Right 12 171500-5622 171740 Unguided 12 171740-1207 Unguided 12 172130-1207 172130-3207 Left 12 172130-3237 172130 172130-3267 172130-5207 Right 12 172130-5237 172130-5267 Assembly Order Number 171500-3122 171500-3722 171500-5122 171500-5722 171740-1208 172130-1208 172130-3208 172130-3238 172130-3268 172130-5208 172130-5238 172130-5268 171500-3222 171500-3322 171500-3422 171500-3522 171500-3822 171500-5222 171500-5322 171500-5422 171500-5522 171500-5822 172130-3217 172130-3247 172130-3277 172130-5217 172130-5247 172130-5277 Tool Setup ALONE Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1. 172130-3218 172130-3248 172130-3278 172130-5218 172130-5248 172130-5278 172130-3227 172130-3257 172130-3287 172130-5227 172130-5257 172130-5287 172130-3228 172130-3258 172130-3288 172130-5228 172130-5258 172130-5288 WITH 62201-95XX RAIL PRESS-IN TOOL PRESS-IN TOOL HOUSING Figure 1 Doc No: ATS-622018961 Revision: B Release Date: 12-09-13 Revision Date: 08-29-14 UNCONTROLLED COPY Page 1 of 3 Impel Daughtercard Press-In Tool Tool Installation The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools. Rail Part Number 62201-9501 62201-9502 62201-9503 62201-9504 62201-9509 62201-9511 Rail Overall Length 24mm (0.94 in) 72mm (2.83 in) 156mm (6.14 in) 216mm (8.50 in) 254mm (10.0 in) 305mm (12.0 in) Reference: This Press-In Tool is 28mm (1.10 in.) long. Printed Circuit Board (PCB) Support The Impel connectors require up to 3.6kg (8 lb) of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Press Equipment Recommendations Many types of presses can be used to install Impel connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force and distance data. Doc No: ATS-622018961 Revision: B Release Date: 12-09-13 Revision Date: 08-29-14 UNCONTROLLED COPY Page 2 of 3 Impel Daughtercard Press-In Tool Tool Operation 1. Carefully insert, by hand, the Daughtercard module(s) into the PCB hole pattern. 2. Place the application tool on top of the Daughtercard module with the back guide surface of the tool against the back of the Daughtercard module. See Figure 2. GUIDE SURFACE Figure 2 3. Using the application tool and an appropriate press, seat the Daughtercard module until there is less than 0.10mm (.004 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. 0.10mm .004 in. MAX. Figure 3 There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing). CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer’s instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Visit our Web site at http://www.molex.com Doc No: ATS-622018961 Revision: B Release Date: 12-09-13 Revision Date: 08-29-14 UNCONTROLLED COPY Page 3 of 3