0622020216

*VHDM-HSD™ Press-In Tool *VHDM-HSD™ Backplane Signal Insertion Module Application Tooling Specification Press-In Tool Order No. 62202-0216 FEATURES


Polarized tool prevents product damage. Tool provides uniform distribution of press force across entire pin array. May be used as a stand-alone tool or mounted in an optional tooling holder with other Molex press-in tools. SCOPE Products: 2.00mm (.079") Pitch *VHDM-HSD™ Standard Shield Signal Module Assembly, (60 Circuits), 74979, 74980, 74981, and 74984, Series, 6 Rows by 10 Columns Assemblies. See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. 74979-1001 74979-1008 74979-9001 74979-9008 74979 Series Number Assembly Order Number 74979-1002 74979-1003 74979-1004 74979-1006 74979-1007 74979-1009 74979-9002 74979-9003 74979-9004 74979-9006 74979-9007 74979-9009 74980-1001 74980-1008 74980-1016 74980-1023 74980-1031 74980-1038 74980-1046 74980-1053 74980-1061 74980-1068 74980-1076 74980-1083 74980-9001 74980-9008 74980-9016 74980-9023 74980-9031 74980-9038 74980-9046 74980-9053 74980 Series Number Assembly Order Number 74980-1002 74980-1003 74980-1004 74980-1009 74980-1011 74980-1012 74980-1017 74980-1018 74980-1019 74980-1024 74980-1026 74980-1027 74980-1032 74980-1033 74980-1034 74980-1039 74980-1041 74980-1042 74980-1047 74980-1048 74980-1049 74980-1054 74980-1056 74980-1057 74980-1062 74980-1063 74980-1064 74980-1069 74980-1071 74980-1072 74980-1077 74980-1078 74980-1079 74980-1084 74980-1086 74980-1087 74980-9002 74980-9003 74980-9004 74980-9009 74980-9011 74980-9012 74980-9017 74980-9018 74980-9019 74980-9024 74980-9026 74980-9027 74980-9032 74980-9033 74980-9034 74980-9039 74980-9041 74980-9042 74980-9047 74980-9048 74980-9049 74980-9054 74980-9056 74980-9057 Guide Style Columns Open End 6 Guide Style Columns Right Doc No: ATS-622020216 Revision: B 6 Release Date: 08-10-99 Revision Date: 06-30-08 74980-1006 74980-1013 74980-1021 74980-1028 74980-1036 74980-1043 74980-1051 74980-1058 74980-1066 74980-1073 74980-1081 74980-1088 74980-9006 74980-9013 74980-9021 74980-9028 74980-9036 74980-9043 74980-9051 74980-9058 UNCONTROLLED COPY 74980-1007 74980-1014 74980-1022 74980-1029 74980-1037 74980-1044 74980-1052 74980-1059 74980-1067 74980-1074 74980-1082 74980-1089 74980-9007 74980-9014 74980-9022 74980-9029 74980-9037 74980-9044 74980-9052 74980-9059 Page 1 of 5 *VHDM-HSD™ Press-In Tool 74980-9061 74980-9068 74980-9076 74980-9083 74980 Series Number Assembly Order Number 74980-9062 74980-9063 74980-9064 74980-9069 74980-9071 74980-9072 74980-9077 74980-9078 74980-9079 74980-9084 74980-9086 74980-9087 74980-9066 74980-9073 74980-9081 74980-9088 74980-9067 74980-9074 74980-9082 74980-9089 74981-1001 74981-1008 74981-1016 74981-1023 74981-1031 74981-1038 74981-1046 74981-1053 74981-1061 74981-1068 74981-1076 74981-1083 74981-9001 74981-9008 74981-9016 74981-9023 74981-9031 74981-9038 74981-9046 74981-9053 74981-9061 74981-9068 74981-9076 74981-9083 74981 Series Number Assembly Order Number 74981-1002 74981-1003 74981-1004 74981-1009 74981-1011 74981-1012 74981-1017 74981-1018 74981-1019 74981-1024 74981-1026 74981-1027 74981-1032 74981-1033 74981-1034 74981-1039 74981-1041 74981-1042 74981-1047 74981-1048 74981-1049 74981-1054 74981-1056 74981-1057 74981-1062 74981-1063 74981-1064 74981-1069 74981-1071 74981-1072 74981-1077 74981-1078 74981-1079 74981-1084 74981-1086 74981-1087 74981-9002 74981-9003 74981-9004 74981-9009 74981-9011 74981-9012 74981-9017 74981-9018 74981-9019 74981-9024 74981-9026 74981-9027 74981-9032 74981-9033 74981-9034 74981-9039 74981-9041 74981-9042 74981-9047 74981-9048 74981-9049 74981-9054 74981-9056 74981-9057 74981-9062 74981-9063 74981-9064 74981-9069 74981-9071 74981-9072 74981-9077 74981-9078 74981-9079 74981-9084 74981-9086 74981-9087 74981-1006 74981-1013 74981-1021 74981-1028 74981-1036 74981-1043 74981-1051 74981-1058 74981-1066 74981-1073 74981-1081 74981-1088 74981-9006 74981-9013 74981-9021 74981-9028 74981-9036 74981-9043 74981-9051 74981-9058 74981-9066 74981-9073 74981-9081 74981-9088 74981-1007 74981-1014 74981-1022 74981-1029 74981-1037 74981-1044 74981-1052 74981-1059 74981-1067 74981-1074 74981-1082 74981-1089 74981-9007 74981-9014 74981-9022 74981-9029 74981-9037 74981-9044 74981-9052 74981-9059 74981-9067 74981-9074 74981-9082 74981-9089 Guide Style Columns Right 6 Guide Style Columns Left 6 Guide Style Columns Custom 6 74984 Series Number Assembly Order Number 74984-0001 74984-0003 74984-0004 74984-0005 74984-0006 74984-0007 74984-0008 74984-0010 74984-0012 74984-0013 74984-0014 74984-0018 74684-0019 74984-0029 74984-9998 *VHDM-HSD™ is a registered trademark of Teradyne, Inc. Doc No: ATS-622020216 Revision: B Release Date: 08-10-99 Revision Date: 06-30-08 UNCONTROLLED COPY Page 2 of 5 *VHDM-HSD™ Press-In Tool Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX tooling holder (ordered separately). See Figure 1. ALONE WITH 62201-95XX TOOLING HOLDER Figure 1 Tool Installation The 62201-95XX tooling holder is available in a variety of lengths to accommodate multiple press-in tools. Tooling Holder Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: The 62202-0216 Press-In Tool is 19.9mm (.785 in.) long by 25.0mm (.984 in.) high. Printed Circuit Board (PCB) Support The *VHDM-HSD™ connectors requires a large amount of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Doc No: ATS-622020216 Revision: B Release Date: 08-10-99 Revision Date: 06-30-08 UNCONTROLLED COPY Page 3 of 5 *VHDM-HSD™ Press-In Tool Press Equipment Recommendations Many types of presses can be used to install *VHDM-HSD™ connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force and distance data. Tool Operation 1. Carefully insert, by hand, the backplane signal module(s) into the PCB hole pattern. Make sure the connector(s) are oriented properly. 2. Insert the press-in-tool into the backplane signal module assembly with the orientation peg on the tool entering the groove in the connector housing. Make sure all the pins and shields fit into the proper slots. See Figure 2. PRESS-IN-TOOL Figure 2 BACKPLANE SIGNAL MODULE ORIENTATION PEG PCB 3. Using the application tool and an appropriate press, seat the header assembly until there is less than 0.25mm (0.01 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. .25mm (0.01”) Maximum Figure 3 Doc No: ATS-622020216 Revision: B Release Date: 08-10-99 Revision Date: 06-30-08 UNCONTROLLED COPY Page 4 of 5 *VHDM-HSD™ Press-In Tool CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer’s instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-622020216 Revision: B Release Date: 08-10-99 Revision Date: 06-30-08 UNCONTROLLED COPY Page 5 of 5