0622020217

*VHDM-HSD™ Press-In Tool *VHDM-HSD™ Backplane Signal Insertion Module Application Tooling Specification Press-In Tool Order No. 62202-0217 FEATURES


Polarized tool prevents product damage. Tool provides uniform distribution of press force across entire pin array. May be used as a stand-alone tool or mounted in an optional tooling holder with other Molex press-in tools. SCOPE Products: 2.00mm (.079") Pitch *VHDM-HSD™ Standard Shield Signal Module Assembly, (150 Circuits), 74979, 74980, 74981, and 74984, Series 6 Rows by 25 Columns Assemblies. See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. 74979-2501 74979-2508 74979-8501 74979-8508 74979 Series Number Assembly Order Number 74979-2502 74979-2503 74979-2504 74979-2506 74979-2507 74979-2509 74979-8502 74979-8503 74979-8504 74979-8506 74979-8507 74979-8509 74980-2501 74980-2508 74980-2516 74980-2523 74980-2531 74980-2538 74980-2546 74980-2553 74980-2561 74980-2568 74980-2576 74980-2583 74980-8501 74980-8508 74980-8516 74980-8523 74980-8531 74980-8538 74980-8546 74980-8553 74980 Series Number Assembly Order Number 74980-2502 74980-2503 74980-2504 74980-2509 74980-2511 74980-2512 74980-2517 74980-2518 74980-2519 74980-2524 74980-2526 74980-2527 74980-2532 74980-2533 74980-2534 74980-2539 74980-2541 74980-2542 74980-2547 74980-2548 74980-2549 74980-2554 74980-2556 74980-2557 74980-2562 74980-2563 74980-2564 74980-2569 74980-2571 74980-2572 74980-2577 74980-2578 74980-2579 74980-2584 74980-2586 74980-2587 74980-8502 74980-8503 74980-8504 74980-8509 74980-8511 74980-8512 74980-8517 74980-8518 74980-8519 74980-8524 74980-8526 74980-8527 74980-8532 74980-8533 74980-8534 74980-8539 74980-8541 74980-8542 74980-8547 74980-8548 74980-8549 74980-8554 74980-8556 74980-8557 Guide Style Columns Open End 6 Guide Style Columns Right Doc No: ATS-622020217 Revision: C 6 Release Date: 08-10-99 Revision Date: 07-01-08 74980-2506 74980-2513 74980-2521 74980-2528 74980-2536 74980-2543 74980-2551 74980-2558 74980-2566 74980-2573 74980-2581 74980-2588 74980-8506 74980-8513 74980-8521 74980-8528 74980-8536 74980-8543 74980-8551 74980-8558 UNCONTROLLED COPY 74980-2507 74980-2514 74980-2522 74980-2529 74980-2537 74980-2544 74980-2552 74980-2559 74980-2567 74980-2574 74980-2582 74980-2589 74980-8507 74980-8514 74980-8522 74980-8529 74980-8537 74980-8544 74980-8552 74980-8559 Page 1 of 5 *VHDM-HSD™ Press-In Tool 74980-8561 74980-8568 74980-8576 74980-8583 74980 Series Number Assembly Order Number 74980-8562 74980-8563 74980-8564 74980-8569 74980-8571 74980-8572 74980-8577 74980-8578 74980-8579 74980-8584 74980-8586 74980-8587 74980-8566 74980-8573 74980-8581 74980-8588 74980-8567 74980-8574 74980-8582 74980-8589 74981-2501 74981-2508 74981-2516 74981-2523 74981-2531 74981-2538 74981-2546 74981-2553 74981-2561 74981-2568 74981-2576 74981-2583 74981-8501 74981-8508 74981-8516 74981-8523 74981-8531 74981-8538 74981-8546 74981-8553 74981-8561 74981-8568 74981-8576 74981-8583 74981-8501 74981 Series Number Assembly Order Number 74981-2502 74981-2503 74981-2504 74981-2509 74981-2511 74981-2512 74981-2517 74981-2518 74981-2519 74981-2524 74981-2526 74981-2527 74981-2532 74981-2533 74981-2534 74981-2539 74981-2541 74981-2542 74981-2547 74981-2548 74981-2549 74981-2554 74981-2556 74981-2557 74981-2562 74981-2563 74981-2564 74981-2569 74981-2571 74981-2572 74981-2577 74981-2578 74981-2579 74981-2584 74981-2586 74981-2587 74981-8502 74981-8503 74981-8504 74981-8509 74981-8511 74981-8512 74981-8517 74981-8518 74981-8519 74981-8524 74981-8526 74981-8527 74981-8532 74981-8533 74981-8534 74981-8539 74981-8541 74981-8542 74981-8547 74981-8548 74981-8549 74981-8554 74981-8556 74981-8557 74981-8562 74981-8563 74981-8564 74981-8569 74981-8571 74981-8572 74981-8577 74981-8578 74981-8579 74981-8584 74981-8586 74981-8587 74981-8502 74981-8503 74981-8504 74981-2506 74981-2513 74981-2521 74981-2528 74981-2536 74981-2543 74981-2551 74981-2558 74981-2566 74981-2573 74981-2581 74981-2588 74981-8506 74981-8513 74981-8521 74981-8528 74981-8536 74981-8543 74981-8551 74981-8558 74981-8566 74981-8573 74981-8581 74981-8588 74981-8506 74981-2507 74981-2514 74981-2522 74981-2529 74981-2537 74981-2544 74981-2552 74981-2559 74981-2567 74981-2574 74981-2582 74981-2589 74981-8507 74981-8514 74981-8522 74981-8529 74981-8537 74981-8544 74981-8552 74981-8559 74981-8567 74981-8574 74981-8582 74981-8589 74981-8507 Guide Style Columns Right 6 Guide Style Columns Left 6 Guide Style Columns Custom 6 74984 Series Number Assembly Order Number 74984-0002 74984-0015 74984-0016 74984-0017 74984-0020 74984-0021 74984-0022 74984-0027 74984-0028 74984-9997 74984-9999 **VHDM-HSD™ is a registered trademark of Teradyne, Inc. Doc No: ATS-622020217 Revision: C Release Date: 08-10-99 Revision Date: 07-01-08 UNCONTROLLED COPY Page 2 of 5 *VHDM-HSD™ Press-In Tool Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX tooling holder (ordered separately). See Figure 1. ALONE WITH 62201-95XX TOOLING HOLDER Figure 1 Tool Installation The 62201-95XX tooling holder is available in a variety of lengths to accommodate multiple press-in tools. Tooling Holder Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: The 62202-0217 Press-In Tool is 49.9mm (1.966 in.) long by 25.0mm (.984 in.) high. Printed Circuit Board (PCB) Support The *VHDM-HSD™ connectors requires a large amount of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Doc No: ATS-622020217 Revision: C Release Date: 08-10-99 Revision Date: 07-01-08 UNCONTROLLED COPY Page 3 of 5 *VHDM-HSD™ Press-In Tool Press Equipment Recommendations Many types of presses can be used to install *VHDM-HSD™ connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force and distance data. Tool Operation 1. Carefully insert, by hand, the backplane signal module(s) into the PCB hole pattern. Make sure the connector(s) are oriented properly. 2. Insert the press-in-tool into the backplane signal module assembly with the orientation peg on the tool entering the groove in the connector housing. Make sure all the pins and shields fit into the proper slots. See Figure 2. PRESS-IN-TOOL Figure 2 BACKPLANE SIGNAL MODULE ORIENTATION PEG PCB 3. Using the application tool and an appropriate press, seat the header assembly until there is less than 0.25mm (0.01 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. .25mm (0.01”) Maximum Figure 3 Doc No: ATS-622020217 Revision: C Release Date: 08-10-99 Revision Date: 07-01-08 UNCONTROLLED COPY Page 4 of 5 *VHDM-HSD™ Press-In Tool CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer’s instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-622020217 Revision: C Release Date: 08-10-99 Revision Date: 07-01-08 UNCONTROLLED COPY Page 5 of 5