0622025220

zQSFP+ Multi-Port Connector Tooling 2-by-2 zQSFP+ Extraction Tool Application Tooling Specification Sheet Order No. 62202-5220 FEATURES Used for removal of a zQSFP+ assembly from a PCB Removes connector from the PCB without damage to the board Use tool 62202-5260 to insert 171565 and 171722 connector assemblies Use tool 62202-5310 to insert 172564 connector assemblies SCOPE Products: zQuad Small Form-factor Pluggable Plus (zQSFP+) Cage Assembly, with Elastomeric Gasket or Metal EMI Gasket, 2 by 2 Enhanced EMI Cage Construction. Connector Series No. Connector Order No. 171565 171565-0001 171565-0002 171565-0003 171565-2001 171565-2002 171565-2003 171722 171722-2001 171722-2002 171722-2003 171722-2062 172564 171564-2001 171564-2002 171564-2003 Notes: 1. See the following pages for tooling operation instructions. 2. These tools require a “Keep Out Zone” around the connector free of components. The right and left sides should be 0.08” (2mm). See Figure 1. zQSFP+ CAGE ASSEMBLY zQSFP+ CAGE 172564 ASSEMBLY 5mm MINIMUM 3.5mm MINIMUM (BOTH SIDES) Doc. No: ATS-622025220 Revision: C PCB KEEP OUT ZONE Release Date: 04-15-13 Revision Date: 02-10-17 2mm MINIMUM (BOTH SIDES) Figure 1 UNCONTROLLED COPY PCB KEEP OUT ZONE Page 1 of 3 zQSFP+ Multi-Port Connector Tooling SUPPORT LOCK (INSERT) REMOVE THE SCREWS AND WASHERS PCB CONNECTOR ASSEMBLY SLIDE UP SLIDE REMOVE UPPER TOOLING SUPPORT BLOCK (FULLY SEATED) SUPPORT TOOLING Figure 2 Figure 3 CONNECTOR ASSEMBLY Description The following instructions are used for removing a 2-by-2 connector from a PCB: Operation 1. Disassemble the (2) halves by unscrewing the screws on the top of the “upper tooling”. See Figure 2. 2. Remove the upper tooling from the support tooling. 3. Insert the support tooling into the cage ports until it is fully seated. See Figure 3. 4. Place the top removal assembly over the support tooling and the cage assembly, aligning the screw holes of the top removal assembly with the threaded holes in the support blocks. See Figure 4. 5. If the top removal assembly does not fit over the cage, the side supports of the top assembly can be adjusted farther from the cage sides. 6. Place the washers and M5 screws into the holes in the top removal assembly; turn the screws clockwise until they are started in the support blocks. SCREWS AND WASHERS TOP REMOVAL ASSEMBLY SUPPORT TOOLING PCB Figure 4 Doc. No: ATS-622025220 Revision: C Release Date: 04-15-13 Revision Date: 02-10-17 UNCONTROLLED COPY Page 2 of 3 zQSFP+ Multi-Port Connector Tooling 7. Using a 4mm hex wrench, tighten each screw, one turn in an alternating pattern until the cage assembly is removed from the PCB. See Figure 5. SUPPORT TOOLING PCB PCB CONNECTOR ASSEMBLY CONNECTOR ASSEMBLY REMOVED Figure 5 CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Application Tooling Support Phone: +1-402-458-TOOL (8665) E-Mail: applicationtooling@molex.com Website: www.molex.com/applicationtooling Doc. No: ATS-622025220 Revision: C Release Date: 04-15-13 Revision Date: 02-10-17 UNCONTROLLED COPY Page 3 of 3