0622025230

zQSFP+ Multi-Port Connector Tooling 2-by-3 zQSFP+ Extraction Tool Application Tooling Specification Sheet Order No. 62202-5230 FEATURES Used for removal of a zQSFP+ assembly from a PCB Removes connector from the PCB without damage to the board Use tool 62203-5240 to insert 71233-000x series Use tool 62202-5270 to insert 171233-1010 Use tool 62202-5330 to insert 171233-5xxx series Use tool 200214-0090 to insert 171985 series SCOPE Products: zQuad Small Form-factor Pluggable Plus (zQSFP+) Cage Assembly, with Elastomeric Gasket or Metal EMI Gasket, 2 by 3 Enhanced EMI Cage Construction. Series No. Connector Order No. 171233 171233-0002 171233-0003 171233-0004 171233-1010 171233-5002 171233-5003 171233-5004 171985 171985-1000 171985-2001 171985-2002 171985-2003 171985-7701 zQSFP+ CONNECTOR ASSEMBLY zQSFP+ CAGE ASSEMBLY 5.0mm MINIMUM 5.0mm MINIMUM 2.0mm MINIMUM (BOTH SIDES) PCB KEEP OUT ZONE KEEP OUT ZONE zQSFP+ CAGE ASSEMBLY (171233) Figure 1 PCB 3.50mm MINIMUM (BOTH SIDES) 5.0mm MINIMUM 2.0mm MINIMUM (BOTH SIDES) PCB Notes: KEEP OUT ZONE 1. See the following pages for tooling operation instructions. 2. These tools require a “Keep Out Zone” around the connector free of components. The right and left sides should be 2mm (0.08”) and the rear of the connector should be 5.0mm (.197”). See Figure 1. Doc. No: ATS-622025230 Revision: B Release Date: 10-04-13 Revision Date: 10-28-16 UNCONTROLLED COPY Page 1 of 3 zQSFP+ Multi-Port Connector Tooling SUPPORT LOCK (INSERT) REMOVE THE SCREWS AND WASHERS PCB CONNECTOR ASSEMBLY SLIDE SLIDE UP REMOVE UPPER TOOLING SUPPORT BLOCK (FULLY SEATED) Figure 3 SUPPORT TOOLING Figure 2 CONNECTOR ASSEMBLY Description The following Instructions are used for removing a 2-by-3 connector from a PCB. Operation 1. Disassemble the (2) halves by unscrewing the screws on the top of the “upper tooling”. See Figure 2. 2. Remove the upper tooling from the support tooling. 3. Insert the support tooling into the cage ports until it is fully seated. See Figure 3. SCREWS 4. Place the top removal assembly over the support tooling and the AND cage assembly, aligning the screw holes of the top removal WASHERS assembly with the threaded holes in the support blocks. See Figure 4. 5. If the top removal assembly does not fit over the cage, the side supports of the top assembly can be adjusted farther from the cage sides. 6. Place the washers and M5 screws into the holes in the top removal TOP REMOVAL assembly; turn the screws clockwise until they are started in the ASSEMBLY support blocks. Figure 4 SUPPORT TOOLING PCB Doc. No: ATS-622025230 Revision: B Release Date: 10-04-13 Revision Date: 10-28-16 UNCONTROLLED COPY Page 2 of 3 zQSFP+ Multi-Port Connector Tooling 7. Using a 4mm hex wrench, tighten each screw, one turn in an alternating pattern until the cage assembly is removed from the PCB. See Figure 5. SUPPORT TOOLING PCB PCB CONNECTOR ASSEMBLY Figure 5 CONNECTOR ASSEMBLY REMOVED CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Visit our Web site at http://www.molex.com Doc. No: ATS-622025230 Revision: B Release Date: 10-04-13 Revision Date: 10-28-16 UNCONTROLLED COPY Page 3 of 3