0622025290

Stacked Multi-Port Connector Tooling 2-by-12 Stacked Multi-Port Removal Tool Application Tooling Specification Sheet Order No. 62202-5290 FEATURES Lightweight tool used in the removal of Stacked Multi-Port connectors in a PCB Removes connector in a PCB without damage to the board Use tool 62202-5280 for inserting connectors SCOPE Products: Small Form-factor Pluggable (zSFP+) 2-by-12 Multi-Port Connector with Press-fit PC Tails. Connector Series No. 170071 171224 172501 Connector Order No. 170071-1201 171224-1201 171224-1215 171224-1260 172501-1202 170071-1211 171224-1209 171224-1230 171224-1261 170071-1212 171224-1211 171224-1231 170071-1213 171224-1212 171224-1241 170071-1214 171224-1213 171224-1242 170071-1215 171224-1214 171224-1250 Notes: 1. See the following pages for tooling operation instructions. 2. These tools require a “Keep Out Zone” around the connector free of components. The right and left sides should be 0.08” (2mm). The rear of the connector should be .197” (5.0mm). See Figure 1. zSFP+ CAGE ASSEMBLY 5mm MINIMUM Figure 1 2mm MINIMUM (BOTH SIDES) PCB KEEP OUT ZONE Doc. No: ATS-622025290 Revision: C Release Date: 09-13-13 Revision Date: 06-05-17 UNCONTROLLED COPY Page 1 of 3 Stacked Multi-Port Connector Tooling REMOVE THE SCREWS AND WASHERS Description The following instructions are used for removing a 2-by-12 connector from a PCB: REMOVE UPPER TOOLING Operation 1. Disassemble the two halves as delivered by unscrewing the screws on the top of the upper tooling. See Figure 2. 2. Remove the upper tooling from the support tooling. 3. For the zSFP+ product, remove the flange, if applicable, from the connector assembly to ensure full insertion of support tooling into connector ports. 4. Insert the support block assembly into the connector assembly until it is fully seated. See Figure 3. SUPPORT TOOLING Figure 2 CONNECTOR ASSEMBLY (WITH THE FLANGE REMOVED) SUPPORT BLOCK (INSERT) Figure 3 PCB SLIDE CONNECTOR ASSEMBLY SUPPORT BLOCK (FULLY SEATED) 5. Place the top removal assembly over the support block and the connector assembly, aligning the front tab of the top removal assembly with the back edge of the support block. See Figure 4. 6. Place the washers and screws into the holes in the top removal assembly, and turn until seated on the top plate using a 5/32” hex wrench to tighten the screws. 7. Tighten each screw, one turn in an alternating pattern, until the connector assembly is removed from the PCB. See Figure 5. Doc. No: ATS-622025290 Revision: C Release Date: 09-13-13 Revision Date: 06-05-17 UNCONTROLLED COPY Page 2 of 3 Stacked Multi-Port Connector Tooling SCREWS AND WASHERS PCB FRONT TAB CONNECTOR ASSEMBLY TOP REMOVAL ASSEMBLY SUPPORT TOOLING SUPPORT TOOLING PCB Figure 4 PCB CONNECTOR ASSEMBLY REMOVED Figure 5 CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Application Tooling Support Phone: (402) 458-TOOL (8665) E-Mail: applicationtooling@molex.com Website: www.molex.com/applicationtooling Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners. Doc. No: ATS-622025290 Revision: C Release Date: 09-13-13 Revision Date: 06-05-17 UNCONTROLLED COPY Page 3 of 3