0622030029

Impact™ Daughtercard Press-In Tool Impact™ Orthogonal Direct Ram Module Installation Press-In Tool Application Tooling Specification Sheet Order No. 62203-0029 FEATURES Lip provided for positive alignment to connector assembly. Tool provides uniform distribution of press force across entire pin array. May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools. Use removal tool 62203-4300 for extracting the connectors SCOPE Products: Impact™ 100Ω Orthogonal Direct Ram Module Assembly (6-Pair by 12 Column Assemblies). See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. Series No. Guide Style Columns Assembly Order Number Unguided 12 171576-1214 171576-1215 171576-1217 171576-1218 171576 Top 12 171576-7204 171576-7205 171576-7207 171576-7208 Bottom 12 171576-9204 171576-9205 171576-9207 171576-9208 Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1. PRESS-IN TOOL ALONE CONNECTOR ASSEMBLY Doc No: ATS-622030029 Revision: B Release Date: 04-24-12 Revision Date: 09-04-12 WITH 62201-95XX RAIL Figure 1 UNCONTROLLED COPY Page 1 of 3 Impact™ Daughtercard Press-In Tool Tool Installation The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools. Rail Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: This Press-In Tool is 26.0mm (1.02 in.) long. Printed Circuit Board (PCB) Support The Impact™ connectors require up to 3.6kg (8 lb) of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Press Equipment Recommendations Many types of presses can be used to install Impact™ connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force and distance data. Doc No: ATS-622030029 Revision: B Release Date: 04-24-12 Revision Date: 09-04-12 UNCONTROLLED COPY Page 2 of 3 Impact™ Daughtercard Press-In Tool Tool Operation 1. Carefully insert, by hand, the Orthogonal Direct Ram module(s) into the PCB hole pattern. 2. Place the application tool on top of the Orthogonal Direct Ram module with the back guide surface of the tool against the back of the Orthogonal Direct Ram module. See Figure 2. GUIDE SURFACE CONNECTOR ASSEMBLY PRESS-IN TOOL PUSH SURFACES PCB Figure 2 3. Using the application tool and an appropriate press, seat the Orthogonal Direct Ram module until there is less than 0.10mm (.004 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. 0.10mm .004 in. Figure 3 MAX. PCB There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing). CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer’s instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Visit our Web site at http://www.molex.com Doc No: ATS-622030029 Revision: B Release Date: 04-24-12 Revision Date: 09-04-12 UNCONTROLLED COPY Page 3 of 3