0636005861

PB14 De-Taping Unit DE-TAPING UNIT For PB14 Terminator Tool Installation and Operation Manual Order No. 69127-5045  Description  Operation  Maintenance Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 1 of 24 PB14 De-Taping Unit Table of Contents Safety Warnings and Information .................................................................................................................................. 3 Tooling Technical Assistance .................................................................................................................................... 4 Section 1 – General Description .................................................................................................................................... 5 1.1 1.2 1.3 1.4 1.5 1.6 Description .................................................................................................................................................... 6 Features ........................................................................................................................................................ 6 Technical Specification .................................................................................................................................. 6 Delivery Check .............................................................................................................................................. 6 Tools.............................................................................................................................................................. 6 Products ........................................................................................................................................................ 7 Section 2 – Installation and Operation ........................................................................................................................... 8 2.1 2.2 2.3 Installation ................................................................................................................................................... 10 Adjustments ................................................................................................................................................. 11 Operation..................................................................................................................................................... 12 Section 3 – Maintenance ............................................................................................................................................. 13 3.1 3.2 3.3 3.4 Cleaning ...................................................................................................................................................... 14 Cleaning ...................................................................................................................................................... 14 Spare Parts ................................................................................................................................................. 14 Troubleshooting ........................................................................................................................................... 15 Section 4 – Parts Lists and Assembly Drawings.......................................................................................................... 16 4.1 4.2 PB14 De-Taping Unit Parts List ................................................................................................................... 17 Reel Arm Assembly (Figure 4-2) ................................................................................................................. 18 Control Box Parts List (Figure 4-3) .............................................................................................................. 19 Control Box Assembly ................................................................................................................................. 20 Take-Up Unit Assembly Parts List (Figure 4-4) ........................................................................................... 21 Take-Up Unit Assembly (Figure 4-4) ........................................................................................................... 22 In-Feed Guide Assembly (Figure 4-5) ......................................................................................................... 23 Schematic Drawing...................................................................................................................................... 24 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 2 of 24 PB14 De-Taping Unit Safety Warnings and Information Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Keep this manual available when using this tool. Replacement manuals are available for download at www.molex.com. SAFETY ALERT SYMBOL This symbol is used to call your attention to hazards or unsafe practices which could result in an injury or property damage. The signal word, defined below, indicates the severity of the hazard. The message after the signal word provides information for preventing or avoiding the hazard. DANGER: DANGER  Indicates an imminently hazardous situation that, if not avoided, could result in death or serious injury WARNING: WARNING  Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury CAUTION: CAUTION  Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury  May also be used to alert against unsafe practices associated with events that could lead to personal injury WARNING Always wear proper eye protection when operating or servicing these tools. Failure to wear eye protection could result in serious eye injury from flying debris. WARNING Never wear clothing or jewelry that is loose or that could potentially get caught in the equipment. Failure to observe this warning could result in severe injury or death. WARNING Never install or service these tool while connected to any electrical power source. Disconnect power by unplugging the press from its power source. Failure to observe this warning could result in severe injury or death. WARNING Use Extreme Caution when using compressed air to clean the equipment. The forces created by compressed air can force debris into the tool. Failure to observe these precautions may result in injury or property damage. WARNING Never operate, service, install or adjust this machine without proper instruction and without first reading and understanding the instructions in this manual and all applicable press or wire processing machine manuals. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 3 of 24 PB14 De-Taping Unit WARNING Never use a press or wire processing machine without guards or safety devices. Failure to observe this warning could result in severe injury or death. CAUTION Caution: Operators must undergo suitable training before using this machine. Caution: A machinery installation safety assessment checklist must be completed before the machine is used in production. Never perform any service or maintenance other than as described in this manual. Never modify, alter or misuse the equipment. Never use this machine for outdoor use. The machine is not water resistant, and improper use may result in damage to the unit. Failure to observe this precaution may result in injury and property damage. Tooling Technical Assistance Molex offers tooling technical assistance for customers who may need some guidance for tooling adjustments. This support can be obtained by calling the number listed below and asking for the Molex Tooling Group. This assistance is limited to the operation and setup of a customer’s Molex De-Taping Unit. Questions with regard to Molex connector products or how to identify the proper tooling or tooling documentation should be directed to your local Molex personnel or customer service representative. When calling for service on these tools, it is recommended to have the following present: a copy of the operation manual, the specific Application Tooling Specification sheet and a person familiar with the tools. Please provide the following information as well: 1. 2. 3. 4. 5. 6. 7. 8. Customer name Customer address Person to contact (e.g., name, title, e-mail address and telephone number) Tool order number (Lease number also if applicable) Serial number (Lease number also if applicable) Molex connector product order number Urgency of request Nature of problem Application Tooling Support Phone: (402) 458-TOOL (8665) E-Mail: applicationtooling@molex.com Website: www.molex.com/applicationtooling Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 4 of 24 PB14 De-Taping Unit Section 1 – General Description 1.1 Description 1.2 Features 1.3 Technical Specifications 1.4 Delivery Check 1.5 Tools 1.6 Products Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 5 of 24 PB14 De-Taping Unit 1.1 Description The PB14 De-Taping Unit automatically pulls off the adhesive tape from 90327 series reeled connectors, 4 to 26 circuits. Pneumatic Requirements No compressed air is required for the De-Taping Unit. This unit is intended for use on the 69127-1001 PB14 terminator. Production Rate with De-Taping Unit This machine terminates 1,000 to 1,700 per hour maximum, depending on operator skill and cable length. A taped strip of connectors is loaded into the vertical magazine and then loaded into the termination nest. As connectors are terminated, the De-Taping Unit pulls off the adhesive tape from the strip so the next connector can fall into place. 1.2 Features   Mounts to the PB14 without modifications. No compressed air required for de-taping. 1.3 Technical Specification Dimensions (PB14 with De-Taping Unit) Width: 475mm (19") Depth: 450mm (18") Height: 670mm (26") Weight (De-Taping Unit only) 10kg (22 lbs.) Electrical Requirements 100-240VAC, 50/60Hz, 1A Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 1.4 Delivery Check Carefully remove the PB14 De-Taping Unit from its shipping container and determine that the following items are included in the package: Description 69127-5045 PB14 De-Taping Unit TM-691275045 Operation Manual Qty. 1 1 1.5 Tools The following tools are recommended for setting up and adjusting the De-Taping Unit:      Metric standard hex wrench set Scissors Large and small regular screwdrivers Pliers (needle nose) Eye Loupe (10x) UNCONTROLLED COPY Page 6 of 24 PB14 De-Taping Unit 1.6 Products 4 Circuit 6 Circuit 8 Circuit 10 Circuit 12 Circuit 14 Circuit 16 Circuit 18 Circuit 20 Circuit 22 Circuit 24 Circuit 26 Circuit 90327 Connector Assembly Series Number 90327-0304 90327-0351 90327-0352 90327-0353 90327-3304 90327-3351 90327-3352 90327-3353 90327-0306 90327-0355 90327-0356 90327-0357 90327-3306 90327-3355 90327-3356 90327-3357 90327-0308 90327-0359 90327-0360 90327-0361 90327-3308 90327-3359 90327-3360 90327-3361 90327-0310 90327-0363 90327-0364 90327-0365 90327-3310 90327-3363 90327-3364 90327-3365 90327-0312 90327-0367 90327-0368 90327-0369 90327-3312 90327-3367 90327-3368 90327-3369 90327-0314 90327-0371 90327-0372 90327-0373 90327-3314 90327-3371 90327-3372 90327-3373 90327-0316 90327-0375 90327-0376 90327-0377 90327-3316 90327-3375 90327-3376 90327-3377 90327-0318 90327-0379 90327-0380 90327-0381 90327-3318 90327-3379 90327-3380 90327-3381 90327-0320 90327-0383 90327-0384 90327-0385 90327-3320 90327-3383 90327-3384 90327-3385 90327-0322 90327-0391 90327-0392 90327-0393 90327-3322 90327-3391 90327-3392 90327-3393 90327-0324 90327-0395 90327-0396 90327-0397 90327-3324 90327-3395 90327-3396 90327-3397 90327-0326 90327-0387 90327-0388 90327-0389 90327-3326 90327-3387 90327-3388 90327-3389 Use with 90328 Terminal Series 90328-0001 90327 Connector Assembly 90327-03xx 90328-0002 90328-0008 90327 Connector Assembly 90327-33xx 90328-0009 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 90327-0354 90327-3354 90327-0358 90327-3358 90327-0362 90327-3362 90327-0366 90327-3366 90327-0370 90327-3370 90327-0374 90327-3374 90327-0378 90327-3378 90327-0382 90327-3382 90327-0386 90327-3386 90327-0394 90327-3394 90327-0398 90327-3398 90327-0390 90327-3390 Chain Loose Chain Loose UNCONTROLLED COPY Page 7 of 24 PB14 De-Taping Unit Section 2 – Installation and Operation 2.1 Installation 2.2 Adjustments 2.3 Operation Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 8 of 24 PB14 De-Taping Unit Principal Mechanical Parts of the PB14 De-Taping Unit REEL ARM ASSEMBLY INFEED GUIDE TAKE-UP UNIT PB14 (69127-1001) REFERENCE REEL FOOT CONTROL BOX REEL SUPPORT Figure 2-1 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 9 of 24 PB14 De-Taping Unit Read the following instructions before attempting to operate the PB14 De-Taping Unit 2.1 Installation 1. Remove the De-Taping Unit from its packing crate, and make sure all packing material has been removed. 2. Mount the Reel Support to the left side of the PB14 using (2) M6 x 20mm long button head cap screws. 3. Place the Reel Foot on the bench, and align the center hole to the hole in the Reel Support. 4. Place the Reel Arm through the hole in the Reel Support and into the hole in the Reel Foot. Tighten the (2) M6 socket head cap screws to clamp the Reel Arm in place. See Figure 2-2. 5. Mount the Take-Up Unit Assembly to the left side magazine rail using (2) M5 x 16mm long socket head cap screws. 6. Mount the In-Feed Guide Assembly to the top of left magazine rail using (2) M5 x 10mm long socket head cap screws and m5 washers. See Figure 2-3. 7. Insert the plug on the motor cord into the receptacle on the front of the control box. 8. Insert the plug on the sensor cord into the receptacle on the front of the control box. 9. Mount the Infeed Guide Assembly to the left magazine rail using (2) M5 x 10mm long socket head cap screws. 10. Connect the AC power cord to the front of the control box, and plug the other end into a grounded AC outlet. M5 X 10 LONG SCREWS AND WASHERS (2) TAKE UP UNIT ASSEMBLY REEL ARM TIGHTEN SCREWS REEL SUPPORT REEL FOOT TIGHTEN SCREWS (2) Figure 2-2 INFEED GUIDE ASSEMBLY LEFT MAGAZINE RAIL Figure 2-3 M5 X 16 LONG SCREWS (2) Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 10 of 24 PB14 De-Taping Unit 2.2 Adjustments Key 69127-5032 De-Taping Adjustments 1. No adjustments are necessary for de-taping. Connector Orientation in PB14 VERTICAL MAGAZINE RAILS CAUTION: Always disconnect the power and air supply before making any adjustments. The connectors are processed with their terminals facing down. 1. A key is inserted into side of the vertical magazine. 2. This key (order number 69127-5032) will allow the connector to travel down the magazine in one direction only. 3. The key can be used in the other vertical magazine to change the orientation of the connector. See Figure 2-4. 4. The key will jam the connectors should the connectors be put into the magazine in the wrong orientation. Figure 2-4 5. The connector will be damaged if it is forced through the magazine rails. 6. To move the key over to the other magazine, undo the one retaining screw and move to the other magazine side. CONNECTORS ON TAPE TAKE-UP REEL VERTICAL MAGAZINE RAILS ADHESIVE ON TAPE REEL ROLLER Figure 2-5 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 11 of 24 PB14 De-Taping Unit 2.3 Operation 1. Load the reel of connectors on the reel arm. The flange of the reel arm should be against the side of the reel, but it must not prevent the reel from turning. The taped side of the connectors goes toward the back of the machine. 2. Thread the connectors down into the magazine rails, peeling away the adhesive tape near the bottom of the stack. 3. Attach the end of the adhesive tape to one of the legs on the take-up reel. See Figure 2-5. 4. Turn on the power switch above the power cord on the control box. 5. Press the power on button near the top of the control box. 6. Operate the PB14 as usual. The sensor on the take-up reel assembly will detect when a connector has been terminated and will wind up the adhesive tape as needed. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 12 of 24 PB14 De-Taping Unit Section 3 – Maintenance 3.1 Cleaning 3.2 Spare parts 3.3 Troubleshooting Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 13 of 24 PB14 De-Taping Unit 3.1 Cleaning CAUTION: Always disconnect the air supply before all maintenance. 3.2 Cleaning 1. Always disconnect the power supply from the De-Taping Unit before cleaning. 2. For efficient operation, the De-Taping Unit and PB14 Terminator should be cleaned daily. Use a soft bristle brush to remove debris from critical areas such as the crimp tooling. 3. Brush and then use a clean cloth to wipe off the upper and lower tooling mounting areas. 4. Keep the face of the tape sensor clean of all debris that may have accumulated during production. An example of a maintenance chart is shown below. Copy and use this chart to track the maintenance of your terminator, or use this as a template to create your own schedule. You can also use your company’s standard chart, if applicable. Preventive Maintenance Chart Daily: Clean. See Section 3.1. CHECK SHEET MONTH/YEAR _________ Week 1 2 3 4 Cleaning Inspect all tooling Days of the Week Daily Daily Cycles Clean MON TUE WED THU FRI SAT SUN Solution Soft Brush Replace if signs of wear. Yes Schedule should be adjusted up or down depending on usage. Molex recommends that a log of preventive maintenance be kept with the press. 3.3 Spare Parts Customers are responsible for maintaining the De-Taping Unit. Spare parts are available. Moving and functioning parts can be damaged or wear out over time and will require replacement. Molex recommends that customers keep some or all of them in stock to reduce production downtime. These parts are identified in the Parts List. See Section 5. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 14 of 24 PB14 De-Taping Unit 3.4 Troubleshooting Symptom Red power light not illuminated Cause Solution 1. Check AC and DC fuses. 2. Make sure power entry switch is on. 1. Make sure motor cable is connected to control box. 2. Adjust product photo sensor.  No power Take-up reel  No power to motor motor not running Take-up reel motor not turning off Consistent bad terminations  Photo sensor not detecting product Adjust photo sensor.  Connector being pushed too far or not far enough  Insertion blade damaged  Terminator jammed with debris Feed finger requires adjustment. See Section 2.2. Replace the insertion blade. See Section 2.2. Clean. See Strip Down in Section 3 Offset to the right will make it difficult to insert cable and will terminate cable at a slight angle. Offset to the left will move the connector away from the feed finger, thus placing the connector in the wrong place for termination. Make sure the connector is touching the end of the brass feed finger at the time of termination. Tighten. Clean. See Strip Down in Section 3  Wire guide set incorrectly  Air pressure too low. Inconsistent bad terminations Connector feed problems  Adjusting screw on the feed finger is loose  Terminator jammed with debris  Operator placing the cable and then moving it slightly to the left  If connector feed is too fast, it may not allow enough time for the connector to drop, the feed finger may strip-out some of the contacts and jam the terminator  If after a connector jam, the terminator does not feed to the correct position. This may be because of a bent feed finger. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 If a new feed finger is required, See Parts List in Section 4. Remove the feed finger and straighten it or replace it. UNCONTROLLED COPY Page 15 of 24 PB14 De-Taping Unit Section 4 – Parts Lists and Assembly Drawings 4.1 Parts Lists and Assemblies 4.2 Schematic Drawings Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 16 of 24 PB14 De-Taping Unit 4.1 PB14 De-Taping Unit Parts List Item 1 2 3 4 5 6 7 8 69127-5045 PB14 De-Taping Unit (Figure 4-1) Order No. Engineering No. Description Qty. Notes 63801-7290 63801-7290 Reel Arm Assembly 1 Figure 4-2 69127-0115 69127-0115 Control Box Assembly 1 Figure 4-3 69127-5055 69127-5055 Take-Up Unit Assembly 1 Figure 4-4 69127-5057 69127-5057 Infeed Guide Assembly 1 Figure 4-5 63890-0048 63890-0048 Reel Support 1 See Figure 4-2 63890-0049 63890-0049 Foot 1 See Figure 4-2 Hardware — — M5 by 10mm long SHCS 2** — — M6 by 20mm long SHCS 2** ** Available from an industrial supply company 1 2 5 4 2 6 9 (2) 2 8 Figure 4-1 (2) 7 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 17 of 24 PB14 De-Taping Unit Reel Arm Assembly (Figure 4-2) Item 1 2 3 4 Order No. 63801-7260 63801-7261 63801-7262 63801-7263 5 69907-3612 63801-7290 Reel Arm Assembly (Figure 4-2) Engineering No. Description Qty. Notes 63801-7260 Reel Support 1 63801-7261 Reel Boss 2 63801-7262 Reel Disc 2 63801-7263 Spring-Reel 1 Hardware — M6 by 12mm Long Wing Screw 2** ** Available from an industrial supply company 4 2 3 (2) (2) 1 5 (2) 63890-0048 Reference Figure 4-2 M6 by 20 LONG SHCS (4) Reference 63890-0049 Reference M5 by 10 LONG SHCS (2) Reference Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 18 of 24 PB14 De-Taping Unit Control Box Parts List (Figure 4-3) Item 22 Order No. 11-41-0264 62500-0960 62500-3232 62500-3234 62500-3235 62500-3238 62500-3239 62500-3240 62500-3241 62500-3242 62500-3244 62500-3245 62500-3246 62500-3247 62500-3259 62500-3389 62500-3430 62500-3431 63700-4610 63600-5861 69127-0138 Make from 62500-3237 69127-0139 23 24 25 26 27 69903-1310 69901-1408 69901-1506 69908-1500 69907-1300 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Doc No: TM-691275045 Revision: H 69127-0115 Control Box Assembly (Figure 4-3) Eng. No. Description Molex Logo Red 2.0 in. KM241 Relay, G2R Type, DIN Rail MT Socket 62500-0960 62500-3232 0.5 A Fast Acting, 0.25" by 1.25" Ceramic Tube 62500-3234 Fuse Holder for 0.25" by 1.25" Tube Fuses 62500-3235 3 A Fast Acting 5 by 20mm Ceramic Tube Power Supply, 12V 30W 62500-3238 M12 4 Pin Female Receptacle 62500-3239 M12 5 Wire Female Rev. Key Receptacle 62500-3240 M12 2 Wire Male 2m Long Cable 62500-3241 62500-3242 M12 5-Wire Reverse Keyed, Field Wireable Connector 62500-3244 Power Cord (250V) Ireland 62500-3245 Power Cord (250V) Europe 62500-3246 Power Cord (125V) North America 62500-3247 Sensor, Laser PNP 62500-3259 SPDT 12VDC Coil, 10AMP Relay 62500-3389 Power Entry With Red Illuminated Switch 62500-3430 Pilot Light, 12VDC Red, 8mm Mounting 62500-3431 MAINT. PB, White, SPDT, 8mm Mounting 63700-4610 Vinyl Cap 63600-5861 12VDC, 8RPM Motor 69127-0138 Enclosure, PB14 DE-Tape 69127-0139 DIN Rail 75mm Long Hardware — M3 by 10 Long FHCS — M4 by 8 Long SHCS — M5 by 6 Long SHCS — M5 Flat Washer — M3 Hex Nut ** Available from an industrial supply company Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Qty. 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes Not Shown Not Shown Not Shown Make from 62500-3237 1 2** 2** 2** 2** 2** Page 19 of 24 PB14 De-Taping Unit Control Box Assembly COVER NOT SHOWN 24 24 6 19 69127-5055 See Figure 4-5 (2) 25 (2) 27 22 15 (2) 26 2 7 3 20 4 8 1 21 10 18 9 23 (2) 17 11 16 Figure 4-3 Doc No: TM-691275045 Revision: H 5 14 (2) 12 Release Date: 12-16-98 Revision Date: 05-07-18 13 UNCONTROLLED COPY Page 20 of 24 PB14 De-Taping Unit Take-Up Unit Assembly Parts List (Figure 4-4) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 69127-5055 Take-Up Unit Assembly (Figure 4-4) Order No. Engineering No. Description Qty. Notes 69018-7110 69018-7110 Coupling 1 69127-5061 69127-5061 Shaft Bearing 1 69127-5085 69127-5085 Bearing Plate 1 69127-5062 69127-5062 Shaft 1 69127-5064 69127-5064 Pin 3 69127-5065 69127-5065 Disc 1 69127-5066 69127-5066 Motor Mounting Spacer 1 69127-5073 69127-5073 Roller pin 1 69127-5079 69127-5079 Roller 1 69127-5084 69127-5084 Detape Base 1 64016-0185 64016-0185 Sensor Mounting Bracket 1 69127-5094 69127-5094 Motor Mounting Plate 1 69127-5095 69127-5095 Coupling Cover 1 Hardware 69901-1108 — M2.5 by 8 Long SHCS 4** 69904-3304 — M3 by 4 Long SSS 2** 69902-1306 — M3 by 6 Long BHCS 1** 69901-1310 — M3 by 10 Long SHCS 2** 69901-1312 — M3 by 12 Long SHCS 4** 69901-1510 — M5 by 10 Long BHCS 4** 69901-1512 — M5 by 12 Long SHCS 2** 69901-1516 — M5 by 16 Long SHCS 3** 69908-1500 — M5 Washer 3** 63600-2979 — M5 Washer Precision 3mm Thick 1** ** Available from an industrial supply company Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 21 of 24 PB14 De-Taping Unit Take-Up Unit Assembly (Figure 4-4) 20 (2) 14 (4) 21 (3) 10 69018-5036 See Figure 4-3 17 (2) 6 17 (2) 11 12 15 8 16 (2) 18 9 1 17 (2) 62500-3247 See Figure 4-3 2 3 4 13 19 (3) 23 22 (3) 7 18 5 (3) Figure 4-4 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 22 of 24 PB14 De-Taping Unit In-Feed Guide Assembly (Figure 4-5) Item 1 2 3 4 5 69127-5057 In-Feed Guide Assembly (Figure 4-5) Order No. Engineering No. Description Qty. Notes 69127-5074 69127-5074 Infeed Chute 1 69127-5089 69127-5089 Infeed Guide 1 Hardware 69904-3310 — M3 by 10 Long SSS Cup Point 2** 69901-1510 — M5 by 10 Long SHCS 2** 69908-1500 — M5 Washer 2** ** Available from an industrial supply company 1 2 3 (2) (2) 5 4 (2) 69127-5006 Reference Figure 4-5 Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 23 of 24 PB14 De-Taping Unit 4.2 Schematic Drawing Application Tooling Support Phone: (402) 458-TOOL (8665) E-Mail: applicationtooling@molex.com Website: www.molex.com/applicationtooling Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners. Doc No: TM-691275045 Revision: H Release Date: 12-16-98 Revision Date: 05-07-18 UNCONTROLLED COPY Page 24 of 24