0638111575

Hand Crimp Tool for Mini-Fit Sr.™ Crimp Terminals HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4B Order No. 63811-1600 FEATURES % % % % A full cycle ratcheting hand tool ensures complete crimps Ergonomically designed soft handles Precisely designed crimping profiles with simple contact positioning Easy handling due to outstanding force ratio SCOPE Products: 10.00 mm (.394”) Pitch Mini-Fit Sr.™ Crimp Terminals, 10-12 AWG. Terminal Order No. Wire Size Insulation Diameter Strip Length Terminal Series No. Loose Piece Reel AWG mm² mm In. mm In. 42815-0010 42815-0011 42815 42815-0012 42815-0018 10-12 N/A 3.50-5.30 .138-.209 7.49-8.51 .295-.335 42815-0114 42817-0010 42817-0011 42817-0012 42817-0018 42817 42817-0019 42817-0110 10-12 N/A 3.50-5.30 .138-.209 7.49-8.51 .295-.335 42817-0111 42817-0112 42817-1014 42817-1114 Customer to cut off terminal from reel: 0.5mm (.020”) maximum Cut-off Tab. * Crimp terminals to stranded copper wire only. DEFINITION OF TERMS 3.75mm ± .20 INSULATION GRIP AREA 3.75mm ± .20 BELL MOUTH SEAM CONTACT GAP 1.00mm ± .20 CONTACT GAP 0.00mm - 0.05mm The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-638111600 Revision: J Release Date: 08-20-01 Revision Date: 09-21-16 UNCONTROLLED COPY Page 1 of 4 Hand Crimp Tool for Mini-Fit Sr.™ Crimp Terminals CONDITIONS: After crimping, the crimp profiles should measure the following (see notes on page 3). Terminal Series No. 42815 42817 Wire Size AWG 10 12 10 12 mm2 N/A N/A N/A N/A Conductor Crimp Height (Ref) Width (Ref) mm In. mm In. 2.69-2.79 .106-.110 3.65 .144 2.39-2.49 .094-098 3.65 .144 2.69-2.79 .106-.110 3.65 .144 2.39-2.49 .094-098 3.65 .144 Insulation Crimp Width (Ref) mm In. 5.80 .228 5.40 .213 5.80 .228 5.40 .213 Pull Force Minimum N Lb. 356.0 80.00 311.0 70.00 356.0 80.00 311.0 70.00 Profile 10 X 12 X X X OPERATION Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles, and the hand tool will spring open. CONDUCTOR GRIPS INSULATION GRIPS LOCATOR Crimping Terminals 1. Place the terminal into the correct die profile (10 or 12) until the terminal stopped by the locator. 2. Partially close the tool until the terminal is held in place. 3. Place a pre-striped wire into the terminal and align the wire with the conductor and insulation grips visually. See Figure 1. 4. Close the tool until the ratchet releases. 5. Carefully remove the crimped terminal. WIRE TERMINAL Figure 2 Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Doc No: ATS-638111600 Revision: J Release Date: 08-20-01 Revision Date: 09-21-16 UNCONTROLLED COPY Page 2 of 4 Hand Crimp Tool for Mini-Fit Sr.™ Crimp Terminals Miscrimps or Jams (See Figure 3) Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by rotating the slotted screw on the locator (back) side of the hand tool. See Figure 3. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. CAUTION CAUTION Molex tooling crimp specifications are valid only when used with Molex terminals and tooling manufactured by Molex or authorized distributors (“Molex Tooling”). When using tooling other than Molex Tooling with specific Molex specific connector systems listed in our ATS documents, the Molex tooling qualification does not apply and the responsibility for full qualification of the connector system is that of the customer. Molex accepts no liability for connector performance or tooling support where tooling other than Molex Tooling is used, or where Molex Tooling is modified. A-620 and other industry standards do not supersede the manufacturer’s specifications. Some terminals designed over 20 years ago may not meet the desired physical attributes for some of today’s standards. However, these terminals will still perform electrically at an acceptable quality level based on the qualification testing and years of successful performance in the field. Notes: 1. This tool should only be used for the terminals and wire gauges specified on this sheet. 2. This tool is not adjustable. Variations in tools, terminals, wire stranding, and insulation types may affect crimp height. 3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes. 4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased. Doc No: ATS-638111600 Revision: J Release Date: 08-20-01 Revision Date: 09-21-16 UNCONTROLLED COPY Page 3 of 4 Hand Crimp Tool for Mini-Fit Sr.™ Crimp Terminals 5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation crimp. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing. 6. Molex does not certify crimp hand tools. 7. Hand held crimping tools are intended for low volume, prototyping, or repair requirements only. CAUTION: Repetitive use of this tool should be avoided. PARTS LIST Item Number 1 Order Number 63811-1575 Description Locator Quantity 1 RATCHET RELEASE SCREW M2.5 WASHER M2.5 X 4mm LONG BHCS 1 Figure 3 Application Tooling Support 2200 Wellington Court Lisle, IL 60532 USA Direct +1-402-458-TOOL (8665) Visit our website at www.molex.com/applicationtooling Doc No: ATS-638111600 Revision: J Release Date: 08-20-01 Revision Date: 09-21-16 UNCONTROLLED COPY Page 4 of 4