0638132100

63813-2100 Modular Card Extractor Tool Module Card Extractor Tool Instruction Manual Part No. 63813-2100 FEATURES % This tool is designed for the removal of the memory module card from the metal latch 87814 series Molex sockets, 1mm pitch, 276-circuit vertical press-fit with metal latch DDR2. SCOPE Products: 87814 Series 276 Circuit Vertical Press-fit Metal Latch DDR2 Dimm Connector System. See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. Assembly Order Number 87814-1001 87814-1002 Description 1.00mm (.039") Pitch DDR-2 DIMM Socket, Vertical, Press-fit, 276 Circuits Metal Latch DESCRIPTION THUMB PUSHER The 1mm pitch, 276-circuit vertical press-fit with metal latch DDR2 takes up a much smaller space inside the housing than a conventional latch will. The entire connector length is almost similar to the module card. However, the latch cannot be extracted by hand and this extraction tool is required to withdrawal the module card from the metal latch. HANDLE METAL LATCH PUSHER The Module Card Extractor Tool consists of modular card latch, metal latch, and thumb pusher with a handle. Figure 1 MODULE CARD LATCH Doc No. 63813-2100 Revision: A Release Date: 05-10--06 Revision Date: 05-10-06 UNCONTROLLED COPY Page 1 of 5 63813-2100 Modular Card Extractor Tool Operation 1. Align the metal latch pushers (2) with the slots on the module card housing. See Figure 2. 2. Push the extractor tool down and into the slots. The module card latches are spring-loaded and will open when extractor tool is engaged in the module card housing. See Figure 3. METAL LATCH PUSHER EXTRACTOR TOOL MODULE CARD LATCHES OPEN MODULE CARD HOUSING PCB BOARD METAL LATCH PUSHER MODULE HOUSING MODULE CARD Figure 2 MODULE CARD Figure 3 METAL LATCH PUSHER 3. Make sure the extractor tool is firmly seated in the slots of the module card housing and the module card latches are locked into the module card. LIFT UP BY THE HANDLE METAL LATCH PUSHER MODULE CARD MODULE CARD LATCHES LOCKED IN PLACE MODULE CARD HOUSING Figure 4 4. Pull the module card straight up with the handle of the extractor tool. See Figure 4. Doc No. 63813-2100 Revision: A Release Date: 05-10--06 Revision Date: 05-10-06 UNCONTROLLED COPY Page 2 of 5 63813-2100 Modular Card Extractor Tool 5. When the module card is free of the housing, press down on the thumb pusher. This will open the module card latches and release the card from the extractor tool. See Figure 5. PUSH DOWN ON THE THUMB PUSHER MODULE CARD MODULE CARD LATCHES WILL RELEASE Figure 5 Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. 4. When tool is not in use, store in a clean, dry area. CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling. Doc No. 63813-2100 Revision: A Release Date: 05-10--06 Revision Date: 05-10-06 UNCONTROLLED COPY Page 3 of 5 63813-2100 Modular Card Extractor Tool PARTS LIST Item Order No Description Quantity 63813-2100 Module Card Extractor Tool (Figure 6) 1 63813-2101 Extractor Base 1 2 63813-2102 Pusher Plate 1 3 63813-2103 Base Cover 1 4 63813-2204 Handle 1 5 63813-2205 Handle Shaft 1 6 63813-2206 Module Card Latch 2 7 63813-2207 Metal Latch Pusher 2 8 63600-2698 Knob 1 9 63600-2699 Metal Bushing 1 10 63600-2700 Compression Spring 1 11 63600-2701 Compression Spring 4 12 63600-2702 1.5mm Diameter Dowel Pin 2 13 63600-2703 M4 Screw Plug 4 14 63600-2704 M3 by 8 Long Low Head SHCS 2 15 N/A M2.5 by 10 Long SHCS **8 16 N/A M3 by 35 Long SHCS **2 17 N/A 4mm by 10 Long Dowel Pin **2 ** Available from an industrial supply company such as MSC (1-800-645-7270). Doc No. 63813-2100 Revision: A Release Date: 05-10--06 Revision Date: 05-10-06 UNCONTROLLED COPY Page 4 of 5 63813-2100 Modular Card Extractor Tool Assembly Drawing 8 16 (2) 4 5 9 (2) 10 6 1 14 15 (8) (2) 17 (2) 12 (2) 2 7 3 (2) 11 (4) 13 (4) Figure 6 Americas Headquarters Far East North Headquarters Far East South Headquarters European Headquarters Corporate Headquarters -JTMF
*MMJOPJT

64"
:BNBUP
,BOBHBXB
+BQBO
+VSPOH
4JOHBQPSF
.VOJDI
(FSNBOZ

8FMMJOHUPO
$U
.0-&9



-JTMF
*-

64"
BNFSJOGP!NPMFYDPN
GFOJOGP!NPMFYDPN
GFTJOGP!NPMFYDPN
FVSJOGP!NPMFYDPN

'BY
 Visit our Web site at http://www.molex.com Doc No. 63813-2100 Revision: A Release Date: 05-10--06 Revision Date: 05-10-06 UNCONTROLLED COPY Page 5 of 5