0638275400

Hand Crimp Tool for ULTRA-FIT Crimp Terminals Application Tooling Specification Sheet Modular Crimp Head Order No. 63827-5470 TYPE 4A Hand Crimp Tool Order No. 63827-5400 FEATURES       A full cycle ratcheting hand tool ensures complete crimps Ergonomically designed soft handles Precisely designed crimping profiles with simple contact positioning Easy handling due to outstanding force ratio Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100, accompanied by Air Powered Crimp Adapter (Order No. 63816-0700). Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V), accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600). SCOPE Products: ULTRA-FIT Crimp Terminals, 20-22 AWG (UL1061) wires. Terminal Series No. 172253 Terminal Order No. Wire Size AWG mm² Type 172253-3111 172253-3112 20-22 --- UL1061 172253-3123 Insulation Diameter UL1061 Wire is Recommended mm In. 1.22-1.44 .048-.057 Strip Length mm In. 3.50-4.00 .138-.158 DEFINITION OF TERMS BEND UP STRIP LENGTH TWISTING BRUSH BELL MOUTH ROLLING BEND DOWN SEAM CUT-OFF TAB CONDUCTOR CRIMP HEIGHT WIRE Doc No: ATS-6382754HM Revision: A Release Date: 01-30-15 Revision Date: 01-30-15 INSULATION CRIMP HEIGHT UNCONTROLLED COPY Page 1 of 6 Hand Crimp Tool for ULTRA-FIT Crimp Terminals CRIMP SPECIFICATION Bell mouth mm In. 0.30-0.50 .012-.020 Terminal Series No. 172253 Terminal Series No. Bend up Bend down 172253 Cut-off Tab Max (Ref) mm In. 0.20 .008 Seam Twist Roll Degree (Max) Degree (Max) 3 3 3 Conductor Brush mm In. 0.00-1.00 .000-.039 5 Seam shall not be open and no wire allowed out of the crimping area After crimping, the conductor profile should measure the following. Wire Size Terminal Series No. 172253 Terminal Series No. 172253 AWG 20 22 Wire Size AWG 20 22 mm2 ----- mm2 ----- Conductor Crimp Height Crimp Width (Max.) mm In. mm In. 0.82-0.92 .032-.036 1.60-1.70 .063-.067 0.73-0.83 .029-.033 1.60-1.70 .063-.067 Insulation Crimp Height (Max.) Crimp Width (Max.) mm In. mm In. 1.90 .075 1.95 .077 1.70 .067 1.65 .065 Profile 20 X 22 X Pull Force Minimum N 57.9 35.6 Lb. 13.0 8.0 Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an optimum crimp. Notes: 1. This tool should only be used for the terminals and wire gauges specified on this sheet. 2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above). Variations in tools, terminals, wire stranding and insulation types may affect crimp height. 3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes. 4. Molex does not repair hand tools (see warranty). The replacement parts listed are the only parts available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased. 5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing. 6. Molex does not certify crimp hand tools. OPERATION Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles, and the hand tool will spring open. Doc No: ATS-6382754HM Revision: A Release Date: 01-30-15 Revision Date: 01-30-15 UNCONTROLLED COPY Page 2 of 6 Hand Crimp Tool for ULTRA-FIT Crimp Terminals 1. With the hand tool in the open position, pivot the SWING terminal locator open by pulling up on the locator knob LOCATOR and lift the wire stop blade up. See Figure 1. OPEN HAND TOOL 2. Insert the terminal into the correct profile until the OPEN terminal is fully seated and stops. WIRE 3. Gently pivot the locator closed. STOP 4. Bring down the wire stop blade. Make sure the wire BLADE stop blade is fully seated on the terminal behind the conductor grip section. TERMINAL 5. Slide the pre-stripped wire into the terminal; make sure SEATED IN to aim the wire brush towards the tip point on the wire Figure 1 LOCATOR stop blade. See Figure 2. Align the wire so that it is parallel and sitting into the terminal. Maintain a light and constant pressure on the wire that is seated in the terminal at all times. (Do not let go of the wire.) Be sure to hold the wire and terminal in place until the terminal is fully crimped. See Figure 3. 6. Close the tool until the ratchet releases. 7. Lift the wire stop blade up. 8. Carefully remove the crimped terminal. Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed. WIRE STOP BLADE TERMINAL CONDUCTOR PUNCH INSULATION PUNCH INSULATION PUNCH WIRE STOP BLADE LOCATOR WIRE TERMINAL CONDUCTOR ANVIL WIRE Figure 2 INSULATION ANVIL Figure 3 Terminal Locator Replacement Removal 1. With the tool in the open position, pivot the terminal locator outward. 2. Remove the M4 BHCS. See Figure 4. Installation 1. Place the new locator, (See Chart on page 2), on the hand tool. Install the M4 BHCS. See Figure 4. 2. Tighten the screw enough to hold the locator. Make sure the locator can still float freely with hand pressure. 3. Insert the proper terminal fully into the correct profile slot until the terminal is fully seated and stops. Then gently pivot the locator closed. 4. With hand pressure, slowly slide the locator to the correct position. See Figure 5. Doc No: ATS-6382754HM Revision: A Release Date: 01-30-15 Revision Date: 01-30-15 UNCONTROLLED COPY Page 3 of 6 Hand Crimp Tool for ULTRA-FIT Crimp Terminals 5. Gently pivot the locator open without disturbing the location. 6. Hold the locator firmly in place and slowly tighten the M4 BHCS. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected M4 BHCS PIVOT LOCATOR with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs Figure 4 cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by lifting the ratchet release lever. See Figure 9. Warranty CORRECT INCORRECT INCORRECT Figure 5 This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Repetitive use of this tool should be avoided. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. Doc No: ATS-6382754HM Revision: A Release Date: 01-30-15 Revision Date: 01-30-15 UNCONTROLLED COPY Page 4 of 6 Hand Crimp Tool for ULTRA-FIT Crimp Terminals Applications for the Modular Crimp Head WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction and without first reading and understanding the instructions in the proper Manual or Specification Sheet. See Chart below for the correct Manual or Specification Sheet. WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the power by unplugging or turn off the Actuator from its power source. CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury. CAUTION: Wear safety glasses when operating or serving this tool. The chart below shows all applications for this Modular Crimp Head. Modular Crimp Head Order No. 63827-5470 Tool Tool Adapter Adapter Figure No. Order no. Description Order No. Description 63816-0000 Hand Crimp Frame (Short) N/A N/A 6 63816-0050 Hand Crimp Frame (Long) N/A N/A 6 63816-0200 Battery Power Tool (110 V) 63816-0600 Battery Power Crimp Adapter 7 63816-0250 Battery Power Tool (220 V) 63816-0600 Battery Power Crimp Adapter 7 63816-0100 Air Power Tool 63816-0700 Air Power Crimp Adapter 8 Hand Crimp Tool Applications for the Modular Crimp Head Battery Powered Tool MODULAR CRIMP HEAD LOCKING PINS MODULAR CRIMP HEAD LOCKING PINS BATTERY POWER CRIMP ADAPTER LOCKING PINS HAND CRIMP FRAME LONG OR SHORT Figure 6 Doc No: ATS-6382754HM Revision: A BATTERY POWERED TOOL Air Powered Tool LOCKING PINS AIR POWER CRIMP ADAPTER LOCKING PINS AIR POWER TOOL Figure 7 Release Date: 01-30-15 Revision Date: 01-30-15 MODULAR CRIMP HEAD UNCONTROLLED COPY Figure 8 Page 5 of 6 Hand Crimp Tool for ULTRA-FIT Crimp Terminals PARTS LIST Item Order Number Description Quantity 1 63827-5470 Modular Crimp Head 1 2 63816-0000 Hand Crimp Frame (Short) 1 3 63827-5475 Locator 1 4 63816-0001 Locking Pin 2 5 63600-0525 Handle Spring 1 6 63600-0520 Crimping Spring 2 5 HANDLE SPRING 2 M4 X 6mm LONG BHCS RATCHET RELEASE LEVER 3 4 1 6 CRIMPING SPRING (2) Figure 9 Visit our Web site at http://www.molex.com Doc No: ATS-6382754HM Revision: A Release Date: 01-30-15 Revision Date: 01-30-15 UNCONTROLLED COPY Page 6 of 6