0638552000

63855-2000 T2 Terminator T2 Terminator Tooling Specification Sheet Part No. 63855-2000 FEATURES Œ Œ Œ Œ Œ This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press It is ideally suited for mid-volume bench operations Quick punch removal with the push of a button for fast and easy tooling change Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab length T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory requirements SCOPE Wire Size Insulation Diameter Strip Length AWG mm² mm In. mm In. 90198-0002 22 - 26 0.35-0.12 1.52 Max .060 Max 2.00-2.50 .079-.098 Terminal will accommodate the following wire specification: 22 AWG-Solid Wire or Fused Wire 24-26 AWG Solid Wire, Fused Wire or Stranded Wire Terminal Series No. DEFINITION OF TERMS BRUSH BEND UP BELL MOUTH CONDUCTOR CRIMP ROLLING SEAM INSULATION CRIMP TWISTING STRIP LENGTH BEND DOWN CUT-OFF TAB CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 1 of 6 63855-2000 T2 Terminator CRIMP SPECIFICATION Bell mouth mm In. None None Terminal Series No. 90198-0002 Bend up Bend down Terminal Series No. 90198-0002 Twist Degree N/A Cut-off Tab Max. mm In. 0.30 .012 Roll Degree N/A N/A N/A Conductor Brush mm In. 0.00-0.10 .000-.004 Punch Width mm (Ref) Conductor Insulation mm In mm In 1.00 .039 1.80 .070 Seam Seam shall not be open and no wire allowed out of the crimping area After crimping, the conductor profile should measure the following. “A” “B” “CRIMP PROFILE” Terminal Series No. 90198-0002 90198-0002 90198-0002 Wire Size 2 AWG mm 22 0.35 24 0.20 26 0.12 “A” Crimp Height mm In 0.89 Ref .035 Ref 0.79 Ref .031 Ref 0.74 Ref .029 Ref “B” Diagonal Dim. mm In. 1.19 Max .047 Max 1.14 Max .045 Max 1.14 Max .045 Max Pull Force Min. N Lb. 35.6 8.0 22.2 5.0 13.3 3.0 Pull Force should be measured with no influence from the insulation crimp. The above specifications are guidelines to an optimum crimp. Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 2 of 6 63855-2000 T2 Terminator PARTS LIST Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Order No Engineering No. Description Quantity 63855-2000 63855-2000 T2 Terminator (Fig. 1) REF 63457-0013 63457-0013 Conductor Punch 1Y 63445-1019 63445-1019 Conductor Anvil 1Y 63454-0021 63454-0021 Insulation Punch 1Y 63445-1834 63445-1834 Insulation Anvil 1Y 63443-0003 63443-0003 Cut-Off Plunger 1Y 63443-0012 63443-0012 Front Plunger Retainer 1Y 11-24-1067 4996-4 Cut-off Plunger Spring 1 63443-3160 63443-3160 Front Plunger Striker 1 63443-0021 63443-0021 Lower Tooling Key 1 63443-6003 63443-6003 Rear Cover 1 11-18-4083 60707-8 Front Cover 1 63443-2405 63443-2405 Anvil Mount 1 63865-2005 63865-2005 Wire Stop 1 63443-0009 63443-0009 Scrape Chute 1 63800-8500 63800-8500 T2 Terminator Frame 1 63443-0058 63443-0058 Ejector Blade Assembly 1 63700-0223 63700-0223 Ejector Blade Spring 1 N/A N/A M3 by 6Lg. SHCS 2** N/A N/A M4 by 6Lg. SHCS 1** N/A N/A M4 by 12Lg. BHCS 2** N/A N/A M4 by 16Lg SHCS 1** N/A N/A M4 by 20Lg. SHCS 1** N/A N/A M4 by 50Lg. SHCS 1** N/A N/A 3MM by 6Lg. Roll Pin 1** N/A N/A #10-32 by 3/8”Lg. BHCS 1** 63855-2070 63855-2070 Tool Kit (All Y Items) REF ** The following purchased parts are available from an Industrial supply company such as MSC (1-800-645-7270). Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 3 of 6 63855-2000 T2 Terminator Assembly Drawing 1 3 (2) (2) 8 20 18 25 10 11 17 16 15 5 21 7 13 12 6 22 9 24 4 23 14 2 19 Figure 1 Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 4 of 6 63855-2000 T2 Terminator NOTES Depending on the press vintage a feed finger assembly is supplied with the T2 Terminator. 1. 2. 3. 4. To remove the existing feed finger assembly loosens the M4 x 10 mm set screw in the feed lever. Select T2 Feed finger assembly from Terminator box. Insert a screwdriver into the slot behind the feed lever and force the feed arm spring to the right. Slide the T2 feed finger shaft for TM42 (11-40-5307) or (11-40-0123) for TM40 /Base Unit into the feed lever and to the left of the feed arm spring. 5. Release the feed arm spring. 6. Position feed finger for selected product. (Refer to Figure 5.1 in the T2 Manual). TM40 PRESS AND BASE UNIT AND ADAPTER TM42 PRESS 11-40-0123 FEED FINGER ROD 11-40-5307 FEED FINGER ROD COTTER PIN 1/8” X .0295 DIA. WIRE COTTER PIN 1/8” X .0295 DIA. WIRE 11-40-5255 FEED FINGER 11-40-5255 FEED FINGER 11-40-0125 FEED ARM SPRING 11-40-0125 FEED ARM SPRING FEED FINGER ASSEMBLY FOR PRESS TM42 FEED FINGER ASSEMBLY FOR PRESS TM40 Figure 2 Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 5 of 6 63855-2000 T2 Terminator NOTES 1. 2. 3. 4. 5. 6. Molex recommends an extra perishable tooling kit be maintained at your facility. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are tight. Slugs, Terminals, Dirt and Oil should be kept clear of work area. This Terminator should be only used in a Molex TM42, TM40, or 3BF Press with a Base Unit adaptor. Wear safety glasses at all times. For recommended maintenance refer to the TM40, TM42 Manual. CAUTION: To prevent injury never operate this Terminator without the guards supplied with the press or in place. Reference the TM42 press manufacturer’s instruction manual. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Molex Application Tooling Group 1150 E. Diehl Road Naperville, IL 60563 Tel: (630) 969-4550 Fax: (630) 505-0049 Visit our Web site at http://www.molex.com Doc No. 63855-2000 Revision: A Release Date: 12-12-03 Revision Date: 12-12-03 UNCONTROLLED COPY Page 6 of 6