Continuous Molded Strip Applicator
Mini-Mac Applicator
Mechanical Feed
Continuous Molded Strip
Application Tooling
Specification Sheet
Order No. 63883-7000
FEATURES
Directly adapts to most crimp presses and automatic wire processors
Applicator designed to industry-standard mounting and shut height of 135.80mm (5.346")
Conductor and insulation rings allow quick adjustment for conductor and cut-off tooling height change
Quick set-up time; plus the crimp height, track and feed adjustments can be set without removing the
applicator from the crimp press
SCOPE
Products: InsulKrimp™ Fully Insulated Quick Disconnect Male and Female Terminals Continuous Molded Strip
for 18-22 AWG.
Testing
Mechanical
The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections.
The following charts show the UL and government specifications (MIL-T-7928) for various wire sizes. The
tensile strength is shown in pounds. It indicates the minimum acceptable force to break or separate the
terminal from the conductor.
Color Code
Yellow
Yellow
Red
Red
Red
Blue
Blue
Yellow
Yellow
Red
Blue
Wire Size (AWG)
26
24
22
20
18
16
14
12
10
8
6
*UL - 486 A
3
5
8
13
20
30
50
70
80
90
100
*UL – 486 C
N/A
N/A
8
10
10
15
25
35
40
45
50
*UL – 310
N/A
N/A
8
13
20
30
50
70
80
N/A
N/A
*Military Class 2
7
10
15
19
38
50
70
110
150
225
300
*UL - 486 A - Terminals (Copper conductors only)
*UL - 486 C - Butt Splices, Parallel Splices, Closed End Connectors, and Wire Nuts
*UL - 310 - Quick Disconnects, Flag and Couplers
*Military Class 2- Military Approved Terminals only as listed
Doc No: ATS-638837000
Revision: D
Release Date: 12-07-04
Revision Date: 05-15-12
UNCONTROLLED COPY
Page 1 of 6
Continuous Molded Strip Applicator
Product List
The following is a partial list of the product order numbers and their specifications that this tool is designed to run.
Updates to this list are available on www.molex.com.
Terminal No.
Terminal Eng. No.
19003-0097
19003-0098
19003-0105
19003-0107
19003-0108
19003-0109
19003-0110
19003-0111
19003-0128
19003-0131
19023-0052
19023-0061
19276-0001
AA-2204C
AA-2205C
AA-2201C
AA-2202C
AA-2203C
AA-2213C
AA-2214C
AA-2201VNC
AA-2202VC
AA-2203VC
19023-0052
19023-0061
AA-2201C-LIF
Wire Size
AWG
mm²
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-.080
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
22-18 0.35-0.80
Insulation Diameter Maximum
mm
In.
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
3.43
.135
Strip Length
mm
In.
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
6.35 .250
DEFINITION OF TERMS
The following illustration is a generic terminal representation and not an exact image of any terminal listed in the
scope.
MWID OR MAX
INSULATION
DIAMETER
Fully Insulated
Female and Male
Quick Disconnect
STRIP
LENGTH
FEMALE QD
MALE QD
REF
CONTINUOUS
MOLDED STRIP
TAB SIZE
TAB SIZE
BRUSH
Figure 1
WIRE STOP
Doc No: ATS-638837000
Revision: D
Release Date: 12-07-04
Revision Date: 05-15-12
UNCONTROLLED COPY
Page 2 of 6
Continuous Molded Strip Applicator
CONDUCTOR
CRIMP DIE
Tool Calibration
To recalibrate this applicator, make sure the power is completely
shut off on the press.
USE SOFT METAL
SLUG METHOD
E2
1. The Mini-Mac applicator must be properly installed in the
press.
“X” CRIMP
2. Crimping dies must be properly installed in the Mini-Mac
HEIGHT
applicator.
E1
3. The recommended method of measuring the crimp height of
CRIMP PROFILE
the conductor dies is the soft metal slug method, (See
Use soft metal slug (solder) method to
Figure 2).
measure the “X” dimension. Verify tooling
4. The slug must have a diameter 0.51mm (.020”) larger than
crimp height calibration by referring to the
the “X” No Go dimension before crimping.
Go/No Go dimensions shown in the chart
5. Place the soft metal slug (solder) into the nest of the bottom
below.
die and crimp (by hand cycling the press) similar to a
terminal. The crimp height can be measured with a blade
Figure 2
type micrometer or dial caliper, (Dimension “X”).
6. Adjustment of the crimp height can be accomplished by indexing the conductor cam. The letter “A” gives the
loosest position and “K” gives the tightest position. A total adjustment of 0.50mm (.020”) can be achieved by
adjusting the conductor cam.
Note: If the crimp height is too tight on the setting “A”, check the shut height of the press. See the Industrial
Mini-Mac Applicator Manual Section 2.1 for adjustments.
CRIMP SPECIFICATIONS
Wire Size
AWG
mm²
22
20
18
0.35
0.50
0.80
“X” Dimension Conductor Crimp
Mean
Go
No Go
In
mm
In
mm
In
mm
.098 2.45 .095 2.41 .103 2.62
.098 2.45 .095 2.41 .103 2.62
.098 2.45 .095 2.41 .103 2.62
Pull Force Minimum
Lbs
N
8.0
13.0
20.0
35.6
57.8
90.0
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Doc No: ATS-638837000
Revision: D
Release Date: 12-07-04
Revision Date: 05-15-12
UNCONTROLLED COPY
Page 3 of 6
Continuous Molded Strip Applicator
PARTS LIST
Mini-Mac Applicator 63883-7000
Item Order No Engineering No.
Description
Quantity
Perishable Tooling
63883-7070
63883-7070
Tool Kit (All “Y” Items)
REF
1
63465-0002
63465-0002
Conductor Punch
1Y
2
63464-0002
63464-0002
Conductor Anvil
1Y
3
63469-0001
63469-0001
Cut-off Punch
1Y
4
63462-0041
63462-0041
Cut-off Anvil
1Y
Other Components
5
63443-0021
63443-0021
Lower Tooling Key
1
6
63466-0912
63466-0912
Anvil Mount
1
7
63466-0913
63466-0913
Terminal Support
1
8
63466-0921
63466-0921
Terminal Stripping Blade
1
9
63466-0931
63466-0931
Terminal Nose Support
1
10
63600-1290
63600-1290
Washer
1
11
63890-0866
63890-0866
Collar-6.4 Long
1
12
63890-0868
63890-0868
Collar-9.5 Long
1
Frame
13
63801-3201
63801-3201
Top
1
14
63801-3281
63801-3281
Base
1
15
63801-4450
63801-4450
Track
1
Hardware
16
N/A
N/A
M3 by 12 Long SHCS
1**
17
N/A
N/A
M4 by 10 Long SHCS
2**
18
N/A
N/A
M4 by 20 Long SHCS
1**
19
N/A
N/A
M4 by 45 Long SHCS
1**
20
N/A
N/A
M5 by 12 Long SHCS
1**
21
N/A
N/A
M8 by 30 Long BHCS
1**
22
N/A
N/A
3mm by 6 Long Roll Pin
1**
** Available from an industrial supply company such as MSC (1-800-645-7270).
Note: Crimp profiles used in 63883-7000 are equivalent to 19030-0156, 19030-0051 / MMC-AA-595, 19030-0159,
19030-0043 / MMC-M-212, 19030-0044 / MMC-M-595, 19028-0059/ACP-M-596, and 19028-0098 (UL file
number E79133).
Doc No: ATS-638837000
Revision: D
Release Date: 12-07-04
Revision Date: 05-15-12
UNCONTROLLED COPY
Page 4 of 6
Continuous Molded Strip Applicator
Assembly Drawing
13
11
1
12
3
10
21
13
9
20
15
7
6
8
2
4
17
(2)
16
18
14
22
19
Doc No: ATS-638837000
Revision: D
5
Release Date: 12-07-04
Revision Date: 05-15-12
Figure 3
UNCONTROLLED COPY
Page 5 of 6
Continuous Molded Strip Applicator
NOTES
1. Molex recommends an extra perishable tooling kit be maintained at your facility.
2. Verify tooling alignment by manually cycling the press with applicator before crimping under power. Check that
all screws are tight.
3. Slugs, terminals, dirt, and oil should be kept clear of work area.
4. Wear safety glasses at all times.
5. For recommended maintenance refer to the Mini-Mac Applicator Manual (Document no. 63880-0000).
CAUTION: This applicator should only be used in a press with a shut height of 135.80 mm (5.346”). Tooling
damage could result at a lower setting.
CAUTION: To prevent injury, never operate this applicator without the guards supplied with the press or wireprocessing machine in place. Reference the press or wire process manufacturer’s instruction manual.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.
Contact Information
For more information on Molex application tooling please contact Molex at 1-800-786-6539.
Visit our Web site at http://www.molex.com
Doc No: ATS-638837000
Revision: D
Release Date: 12-07-04
Revision Date: 05-15-12
UNCONTROLLED COPY
Page 6 of 6
很抱歉,暂时无法提供与“0638837000”相匹配的价格&库存,您可以联系我们找货
免费人工找货- 国内价格 香港价格
- 1+52233.366631+6479.52486