0638850800

Air Feed Mylar Tape Applicator Mini-Mac Applicator Application Tooling Specification Air Feed-Mylar Tape Order No. 63885-0800 FEATURES Œ Œ Œ Œ Directly adapts to most crimp presses and automatic wire processors Applicator designed to industry standard mounting and shut height of 135.80mm (5.346") Conductor and insulation rings allow quick adjustment for conductor and insulation crimp height change Quick set-up time; plus the crimp height, track and feed adjustments can be set without removing the applicator from the crimp press SCOPE Products: Avikrimp Female QD Terminals 18-22 AWG Testing Mechanical The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections. The following chart shows the UL and government specifications (MIL-T-7928) for various wire sizes. The tensile strength is shown in pounds and indicates the minimum acceptable force to break or separate the terminal from the conductor. Color Code Yellow Yellow Red Red Red Blue Blue Yellow Yellow Red Blue Wire Size (AWG) 26 24 22 20 18 16 14 12 10 8 6 *UL - 486 A *UL – 486 C *UL – 310 3 5 8 13 20 30 50 70 80 90 100 N/A N/A 8 10 10 15 25 35 40 45 50 N/A N/A 8 13 20 30 50 70 80 N/A N/A *Military Class 2 7 10 15 19 38 50 70 110 150 225 300 *UL - 486 A - Terminals (Copper conductors only) *UL - 486 C - Butt Splices, Parallel Splices, Closed End Connectors, and Wire Nuts *UL - 310 - Quick Disconnects, Flag and Couplers *Military Class 2- Military Approved Terminals only as listed Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 UNCONTROLLED COPY Page 1 of 7 Air Feed Mylar Tape Applicator Product List The following is a partial list of the product order numbers and their specifications that this tool is designed to run. Updates to this list are available on www.molex.com. Terminal No. 19017-0003 19017-0004 19017-0006 19017-0009 19017-0012 19017-0017 19017-0020 19019-0003 19019-0005 19019-0009 19019-0011 19019-0013 19019-0016 19019-0058 19019-0068 19019-0069 19164-0416 19164-0418 Doc No. 63885-0800 Revision: B Terminal Eng. No. AA-2190T AA-2131T AA-2134T AA-2137-032T AA-2137T AA-2140T AA-2190-032T AA-8131T AA-8134T AA-8137-032T AA-8137T AA-8140T AA-8190T AA-8190-032T AA-8131BT AA-8134-BKT SPL-0369T SPL-0368T Release Date: 12-08-04 Revision Date: 10-03-05 Wire Size AWG mm² 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 22-18 0.35-0.80 Insulation Diameter Max. mm In. 3.43 .135 3.43 .135 3.43 .135 3.43 .135 3.43 .135 3.43 .135 3.43 .135 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 2.90 .115 UNCONTROLLED COPY Strip Length mm In. 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 Page 2 of 7 Air Feed Mylar Tape Applicator DEFINITION OF TERMS The following illustrations are a generic terminal representation and not an exact image of any terminal listed in the scope. Insulated Terminal MWID OR MAX INSULATION DIAMETER Un-Insulated Terminal BARREL BRUSH MWID OR MAX INSULATION DIAMETER STRIP LENGTH STUD SIZE (REF) STUD SIZE (REF) BARREL STRIP LENGTH INSULATION FERRULE BRUSH Figure 1 Figure 2 STRIP LENGTH Fully Insulated Male and Female Quick Disconnect FEMALE QD MWID OR MAX INSULATION DIAMETER BRUSH MALE QD REF TAB SIZE Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 WIRE STOP TAB SIZE Figure 3 UNCONTROLLED COPY Page 3 of 7 Air Feed Mylar Tape Applicator Tool Calibration To recalibrate this applicator, make sure the power is completely shut off on the press. 1. The Mini-Mac applicator must be properly installed in the press. 2. Crimping dies must be properly installed in the Mini-Mac applicator. 3. The recommended method of measuring the crimp height of the conductor dies is the soft metal slug method, (See Figure 4). 4. The slug must have a diameter 0.51mm (.020”) larger than the “X” No Go dimension before crimping. 5. Place the soft metal slug (solder) into the nest of the bottom die and crimp (by hand cycling the press) similar to a terminal. The crimp height can be measured with a blade type micrometer or dial caliper, (Dimension “X”). 6. Adjustment of the crimp height can be accomplished by indexing the conductor cam. The letter “A” gives the loosest position and “K” gives the tightest position. A total adjustment of 0.50mm (.020”) can be achieved by adjusting the conductor cam. CONDUCTOR CRIMP DIE USE SOFT METAL SLUG METHOD E2 “X” CRIMP HEIGHT E1 CRIMP PROFILE Use soft metal slug (solder) method to measure the “X” dimension. Verify tooling crimp height calibration by referring to the Go/No Go dimensions shown in the chart below. Figure 4 Note: If the crimp height is too tight on the setting “A”, check the shut height of the press. See the Industrial Mini-Mac Applicator Manual Section 2.1 for adjustments. CRIMP SPECIFICATIONS Wire Size AWG mm² 22 20 18 0.35 0.50 0.80 “X” Dimension Conductor Crimp Mean Go No Go In mm In mm In mm .086 2.18 .083 2.11 .090 2.29 .086 2.18 .083 2.11 .090 2.29 .086 2.18 .083 2.11 .090 2.29 Pull Force Min. Lbs N 8 13 20 35.6 57.8 90.0 Pull Force should be measured with no influence from the insulation crimp. The above specifications are guidelines to an optimum crimp. Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 UNCONTROLLED COPY Page 4 of 7 Air Feed Mylar Tape Applicator PARTS LIST Mini-Mac Applicator 63885-0800 Description Quantity Item Order No Engineering No. Perishable Tooling 63885-0870 63885-0870 Tool Kit (All “Y” Items) REF 1 63465-0012 63465-0012 Conductor Punch 1Y 2 63464-0012 63464-0012 Conductor Anvil 1Y 3 63463-0009 63463-0009 Insulation Punch 1Y 4 63462-0013 63462-0013 Insulation Anvil 1Y Other Components (Ref. 50050) 31 63466-0912 63466-0912 Anvil Mount 1 32 63466-0913 63466-0913 Terminal Support 1 33 63443-0021 63443-0021 Lower Tooling Key 1 42 63466-0921 63466-0921 Terminal Stripping Blade 1 51 63600-1290 63600-1290 Washer 1 52 63890-0866 63890-0866 Collar-6.4mm Lg. 1 53 63890-0867 63890-0867 Collar-7.7mm Lg. 1 Frame 81 63801-3301 63801-3301 Air Feed Applicator Frame Head REF 82 63801-3281 63801-3281 Base REF 83 63801-5850 63801-5850 Track Assembly REF 84 63801-3390 63801-3390 Air Kit REF Hardware 91 N/A N/A M3 by 12 Lg SHCS 1** 92 N/A N/A M4 by 10 Lg SHCS 2** 93 N/A N/A M4 by 16 Lg. SHCS 1** 94 N/A N/A M4 by 45 Lg. SHCS 1** 95 N/A N/A M8 by 30 Lg. BHCS 1** 96 N/A N/A 3mm by 6 Lg. Roll Pin 1** ** Available from an industrial supply company such as MSC (1-800-645-7270). Note: Crimp profiles used in 63885-0800 are equivalent to 19032-0060/MMT-AA-575, 19288-0048/ATP-AA-575, and 19288-0079/ATP-AA-575-CC (UL file number E79133). Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 UNCONTROLLED COPY Page 5 of 7 Air Feed Mylar Tape Applicator Assembly Drawing 81 52 53 1 81 3 51 95 42 92 (2) 32 83 31 84 2 4 91 93 82 96 94 33 Figure 5 Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 UNCONTROLLED COPY Page 6 of 7 Air Feed Mylar Tape Applicator NOTES 1. Molex recommends an extra perishable tooling kit be maintained at your facility. 2. Verify tooling alignment by manually cycling the press with applicator before crimping under power. Check that all screws are tight. 3. Slugs, terminals, dirt, and oil should be kept clear of work area. 4. Wear safety glasses at all times. 5. For recommended maintenance refer to the Mini-Mac Applicator Manual (Document no. 63880-0000). CAUTION: This applicator should only be used in a press with a shut height of 135.80 mm (5.346”). Tooling damage could result at a lower setting. CAUTION: To prevent injury, never operate this applicator without the guards supplied with the press or wire-processing machine in place. Reference the press or wire processing manufacturer’s instruction manual. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Molex Application Tooling Group 1150 E. Diehl Road Naperville, IL 60563 Tel: (630) 969-4550 Fax: (630) 505-0049 Visit our Web site at http://www.molex.com Doc No. 63885-0800 Revision: B Release Date: 12-08-04 Revision Date: 10-03-05 UNCONTROLLED COPY Page 7 of 7