0638858300

Air Feed Mylar Tape Applicator Mini-Mac Applicator Application Tooling Specification Air Feed-Mylar Tape Part No. 63885-8300 FEATURES



Directly adapts to most crimp presses and automatic wire processors Applicator designed to industry-standard mounting and shut height of 135.80mm (5.346") Conductor and insulation rings allow quick adjustment for conductor and insulation crimp height change Quick set-up time; plus the crimp height, track and feed adjustments can be set without removing the applicator from the crimp press SCOPE Products: Insulkrimp™ Butt Splice Terminals 14-16 AWG. Testing Mechanical The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections. The following chart shows the UL specifications for various wire sizes. The tensile strength is shown in pounds and indicates the minimum acceptable force to break or separate the terminal from the conductor. Color Code Blue Blue Wire Size (AWG) 16 14 *UL – 486 C 15 25 *UL - 486 C - Butt Splices, Parallel Splices, Closed End Connectors, and Wire Nuts Product List The following is a partial list of the product order numbers and their specifications that this tool is designed to run. Updates to this list are available on www.molex.com. Terminal No. Terminal Eng. No. 19154-0014 19154-0017 19154-0021 19154-0024 19154-0057 B-231OVT B-231XT B-L231XT BS-V-331XT BA-631XT Doc No: ATS-638858300 Revision: B Wire Size AWG mm² 14 - 16 2.00 - 1.30 14 - 16 2.00 - 1.30 14 - 16 2.00 - 1.30 14 - 16 2.00 - 1.30 14 - 16 2.00 - 1.30 Release Date: 12-18-08 Revision Date: 01-16-09 Insulation Diameter Maximum mm In. 4.57 .180 4.57 .180 3.81 .150 4.57 .180 4.46 .175 UNCONTROLLED COPY Strip Length mm In. 5.94 .234 5.94 .234 7.14 .281 7.14 .281 7.14 .281 Page 1 of 6 Air Feed Mylar Tape Applicator DEFINITION OF TERMS The following illustrations are a generic terminal representation and not an exact image of any terminal listed in the scope. Insulated Terminal MWID OR MAX INSULATION DIAMETER Un-Insulated Terminal MWID OR MAX INSULATION DIAMETER BARREL BRUSH STRIP LENGTH STUD SIZE (REF) STUD SIZE (REF) BARREL STRIP LENGTH INSULATION FERRULE Figure 2 BRUSH Figure 1 STRIP LENGTH Fully Insulated Male and Female Quick Disconnect FEMALE QD MWID OR MAX INSULATION DIAMETER BRUSH MALE QD REF TAB SIZE Doc No: ATS-638858300 Revision: B WIRE STOP TAB SIZE Release Date: 12-18-08 Revision Date: 01-16-09 Figure 3 UNCONTROLLED COPY Page 2 of 6 Air Feed Mylar Tape Applicator Tool Calibration To recalibrate this Applicator, make sure the power is completely shut off on the press. CONDUCTOR CRIMP DIE USE SOFT METAL SLUG METHOD 1. The Mini-Mac applicator must be properly installed in the E2 press. 2. Crimping dies must be properly installed in the Mini-Mac applicator. 3. The recommended method of measuring the crimp height “X” CRIMP of the conductor dies is the soft metal slug method, (See HEIGHT Figure 4). E1 4. The slug must have a diameter 0.51mm (.020”) larger than CRIMP PROFILE the “X” No Go dimension before crimping. 5. Place the soft metal slug (solder) into the nest of the Use soft metal slug (solder) method to measure the “X” dimension. Verify tooling crimp height bottom die and crimp (by hand cycling the press) similar to a terminal. The crimp height can be measured with a blade calibration by referring to the Go/No Go dimensions shown in the chart below. type micrometer or dial caliper, (Dimension “X”). 6. Adjustment of the crimp height can be accomplished by Figure 2 indexing the conductor cam. The letter “A” gives the loosest position and “K” gives the tightest position. A total adjustment of 0.50mm (.020”) can be achieved by adjusting the conductor cam. Note: If the crimp height is too tight on the setting “A”, check the shut height of the press. See the Industrial Mini-Mac Applicator Manual Section 2.1 for adjustments. CRIMP SPECIFICATIONS Wire Size AWG mm² 14 16 2.00 1.30 “X” Dimension Conductor Crimp Mean Go No Go In mm In mm In mm .108 2.74 .105 2.67 .112 2.84 .108 2.74 .105 2.67 .112 2.84 Pull Force Minimum Lbs N 25 15 111.25 66.75 Pull Force should be measured with no influence from the insulation crimp. The above specifications are guidelines to an optimum crimp. Doc No: ATS-638858300 Revision: B Release Date: 12-18-08 Revision Date: 01-16-09 UNCONTROLLED COPY Page 3 of 6 Air Feed Mylar Tape Applicator PARTS LIST Mini-Mac Applicator 63885-8300 Item Order No Engineering No. Description Quantity Perishable Tooling 63885-8370 63885-8370 Tool Kit (All “Y” Items) REF 1 63465-0062 63465-0062 Conductor Punch 1Y 2 63464-0056 63464-0056 Conductor Anvil 1Y 3 63463-0039 63463-0039 Insulation Punch 1Y 4 63462-0045 63462-0045 Insulation Anvil 1Y Other Components (Ref. 50050) 5 63466-0912 63466-0912 Anvil Mount 1 6 63466-0913 63466-0913 Terminal Support 1 7 63443-0021 63443-0021 Lower Tooling Key 1 8 63466-0921 63466-0921 Terminal Stripping Blade 1 9 63600-1290 63600-1290 Washer 1 10 63890-0866 63890-0866 Collar-6.4mm Long 1 11 63890-0867 63890-0867 Collar-7.7mm Long 1 Frame 12 63801-3301 63801-3301 Air Feed Applicator Frame Head REF 13 63801-3281 63801-3281 Base REF 14 63801-5850 63801-5850 Track Assembly REF 15 63801-3390 63801-3390 Air Kit REF Hardware 16 N/A N/A M3 by 12 Long SHCS 1** 17 N/A N/A M4 by 10 Long SHCS 2** 18 N/A N/A M4 by 20 Long SHCS 1** 19 N/A N/A M4 by 50 Long SHCS 1** 20 N/A N/A M8 by 30 Long BHCS 1** 21 N/A N/A 3mm by 6 Long Roll Pin 1** ** Available from an industrial supply company such as MSC (1-800-645-7270). Note: Crimp profiles used in 63885-8300 are equivalent to 19288-0090 / ATP-B-521 (UL file number E32244). Doc No: ATS-638858300 Revision: B Release Date: 12-18-08 Revision Date: 01-16-09 UNCONTROLLED COPY Page 4 of 6 Air Feed Mylar Tape Applicator Assembly Drawing 12 10 11 1 12 3 9 20 8 17 (2) 6 14 5 15 2 4 16 18 13 21 19 7 Figure 5 Doc No: ATS-638858300 Revision: B Release Date: 12-18-08 Revision Date: 01-16-09 UNCONTROLLED COPY Page 5 of 6 Air Feed Mylar Tape Applicator NOTES 1. Molex recommends an extra perishable tooling kit be maintained at your facility. 2. Verify tooling alignment by manually cycling the press with applicator before crimping under power. Check that all screws are tight. 3. Slugs, terminals, dirt, and oil should be kept clear of work area. 4. Wear safety glasses at all times. 5. For recommended maintenance refer to the Mini-Mac Applicator Manual (Document no. 63880-0000). CAUTION: This applicator should only be used in a press with a shut height of 135.80 mm (5.346”). Tooling damage could result at a lower setting. CAUTION: To prevent injury, never operate this applicator without the guards supplied with the press or wire-processing machine in place. Reference the press or wire processing manufacturer’s instruction manual. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-638858300 Revision: B Release Date: 12-18-08 Revision Date: 01-16-09 UNCONTROLLED COPY Page 6 of 6