0638924600

Mini-Mac Applicator for Claspcon Crimp Terminal Socket Mini-Mac Applicator Specification Sheet Order No. 63892-4600 FEATURES




Directly adapts to most automatic wire processing machines Applicator designed to industry standard mounting and shut height 135.80mm (5.346") Quick set-up time; plus the crimp height, track and feed adjustments can be set without removing the applicator from the press Fine adjustment allows users to achieve target with little effort by adjusting in increments of .015mm (.0006") for conductor crimp height and .063mm (.0025") for insulation height Independent adjustment rings allow users to quickly adjust the conductor or insulation crimp height without affecting each other. SCOPE Products: Claspcon Crimp Terminal Socket, 24-30 AWG Terminal Series No. Terminal Order No. 1881-3 02-08-1103 Wire Size AWG 24-30 mm² 0.05-0.20 Insulation Diameter Maximum mm In. 1.52 .060 Strip Length mm 3.96-5.54 In. .156-.218 DEFINITION OF TERMS C/L
TERMINAL LOCATION BEND UP BELL MOUTH BRUSH ROLLING SEAM INSULATION CRIMP CUT-OFF TAB TWISTING BEND DOWN STRIP LENGTH CONDUCTOR CRIMP HEIGHT CRIMP C/L
Terminal is to be centrally located between the two (2) cut-off tab edges by one half of the total cut-off tab tolerance. This illustration is a generic terminal representation and not an exact image of any terminal listed in the scope. Doc No: ATS-638924600 Revision: A Release Date: 10-30-08 Revision Date: 10-30-08 UNCONTROLLED COPY Page 1 of 5 Mini-Mac Applicator for Claspcon Crimp Terminal Socket CRIMP SPECIFICATIONS Terminal Series No. Bell mouth mm In. 1881 Terminal Series No. 1881
Cut-off Tab mm In. 3.53-3.69 .139-.145 Punch Width (Ref) Conductor Insulation mm In. mm In. 3.475 .137 1.93 .076 Conductor Brush mm In. Seam Seam shall not be open and no wire allowed out of the crimping area NOTE: Some of the specifications in these charts above are intentionally left blank due to the fact that the information does not currently exist. After crimping, the conductor profile should measure the following. Terminal Series No. 1881 Wire Size AWG mm2 24 0.20 26 0.12 28 0.08 30 0.05 Crimp Height Crimp Width (REF) Pull Force Minimum mm In. mm In. N Lb. 0.86-0.91 .034-.036 44.5 10.00 0.74-0.79 .029-.031 26.7 6.00 0.71-0.76 .028-.030 17.8 4.00 0.71-0.76 .028-.030 13.3 3.00 Pull Force should be measured with no influence from the insulation crimp. The above specifications are guidelines to an optimum crimp. Doc No: ATS-638924600 Revision: A Release Date: 10-30-08 Revision Date: 10-30-08 UNCONTROLLED COPY Page 2 of 5 Mini-Mac Applicator for Claspcon Crimp Terminal Socket PARTS LIST Mini-Mac Applicator 63892-4600 Item Order No Engineering No. Description Quantity Perishable Tooling 63892-4670 63892-4670 Tool Kit (All “Y” Items) REF 1 11-18-4053 60706-15 Conductor Punch 1Y 2 11-18-4532 60706-34 Combination Anvil 1Y 3 11-18-4054 60706-16 Insulation Punch 1Y 4 11-18-4447 60706-31 Cut-Off Punch 1Y 5 11-18-4044 60706-6 Cut-off Die Plate 1Y Other Components (REF 924650) 6 11-17-0094 1739-37 Compression Spring 1 7 11-17-1172 4151-20 Terminal Drag Plate 1 8 11-18-4040 60706-2 Cover Plate 1 9 11-18-4042 60706-4 Terminal Guide 1 10 11-18-4043 60706-5 Insulation Punch Holder 1 11 11-18-4422 60706-28 Hold Down Plunger 1 12 11-18-4423 60706-29 Stripper and Wire Stop 1 13 11-18-4446 60706-30 Stripper and Wire Stop Holder 1 14 11-18-4562 60700-15 Slug Ramp 1 15 63803-5105 63803-5105 Conductor Bushing 1 Frame 16 63801-3201 63801-3201 Top 1 17 63801-3282 63801-3282 Base 1 18 63801-6550 63801-6550 Track 1 Hardware 19 N/A N/A M3 by 8 Long SHCS 4** 20 N/A N/A M4 by 12 Long BHCS 2** 21 N/A N/A M4 by 16 Long SHCS 2** 22 N/A N/A M8 by 20 Long BHCS 1** 23 N/A N/A #6-32 by 3/8” Long BHCS 3** 24 N/A N/A #8-32 by 1/4” Long BHCS 1** 25 N/A N/A #1/4-20 by 1/2” Long SHCS 2** 26 N/A N/A 1/8 Diameter by 3/8” Long Roll Pin 2** ** Available from an industrial supply company such as MSC (1-800-645-7270). Doc No: ATS-638924600 Revision: A Release Date: 10-30-08 Revision Date: 10-30-08 UNCONTROLLED COPY Page 3 of 5 Mini-Mac Applicator for Claspcon Crimp Terminal Socket Assembly Drawing 6 11 1 3 21 15 10 4 16 22 20 (2) (2) 23 8 26 (2) (2) 19 18 12 16 7 5 19 2 13 (2) 25 (2) 9 17 14 23 (2) 24 Figure 1 Doc No: ATS-638924600 Revision: A Release Date: 10-30-08 Revision Date: 10-30-08 UNCONTROLLED COPY Page 4 of 5 Mini-Mac Applicator for Claspcon Crimp Terminal Socket NOTES 1. Molex recommends an extra perishable tooling kit be maintained at your facility. 2. Verify tooling alignment by manually cycling the press and applicator before crimping under power. Check that all screws are tight. 3. Slugs, terminals, dirt, and oil should be kept clear of work area. 4. Wear safety glasses at all times. 5. For recommended maintenance refer to the Mini-Mac Manual. CAUTION: This applicator should only be used in a press with a shut height of 135.80 mm (5.346”). Tooling damage could result at a lower setting CAUTION: To prevent injury, never operate this applicator without the guards supplied with the press or wire-processing machine in place. Reference the press or wire processing manufacturer’s instruction manual. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-638924600 Revision: A Release Date: 10-30-08 Revision Date: 10-30-08 UNCONTROLLED COPY Page 5 of 5