0732511852

12 11 10 9 MATERIALS AND FINISHES: H 7 8 .376 REF 9.55 BODY: STAINLESS STEEL PLATED: PASSIVATE 5 6 2 1 H ⌀ .102 REF CENTER CONTACT: BERYLLIUM COPPER PLATED: GOLD (50µ-in) MIN OVER NICKEL (100µ -in) MIN 2.59 1/4-36 UNS-2A INSULATOR: PTFE GROUNDING RING G 3 .223 REF 5.66 .065 REF 1.65 .093 MAX 2.36 4 C SCREW: STAINLESS STEEL PLATED: PASSIVATE G ⌀ .481 REF D SMA JACK INTERFACE F ⌀ .282 REF ⌀ .625 REF 12.21 7.16 15.88 F .218 MIN 5.54 0-80 UNF 2 PLACES MOUNTING SCREWS MUST NOT EXTEND BEYOND THIS POINT E ⌀ .063 ±.001 ⌀ .030 ±.003 0.76 ±0.08 SIGNAL PAD .0025 REF 0.064 ⌀ .170 REF GROUND PAD D E 1.600 ±0.025 2 PLACES THRU ⌀ .088 REF ⌀ .020 ±.001 4.32 GROUND PAD MINIMUM 2.24 INSULATOR OUTER DIAMETER 0.508 ±0.025 CENTER CONTACT .282 ±.002 7.16 ±0.05 SIGNAL PAD C 4.32 GROUNDING RING OUTER DIAMETER D ⌀ .101 ±.002 2.57 ±0.05 GROUND PAD .141 ±.002 3.58 ±0.05 2 PLACES ⌀ .170 REF ⌀ .101 REF ⌀ .037 REF 0.94 INSULATOR INNER DIAMETER +.003 -.000 +0.08 0.13 -0.00 .005 GENERAL PCB LAYOUT DETAIL D SEE SHEET 2 FOR PART NUMBERS 2.57 GROUNDING RING INNER DIAMETER DETAIL C C PS-89675-3460 ELECTO/MECH PERFOR MIL-STD-348B, FIG 310-2 INTERFACE B SPECIFICATION DESCRIPTION B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE CURRENT REV DESC: SEE ECM 117632 DIMENSION UNITS INCH GENERAL TOLERANCES (UNLESS SPECIFIED) MM A 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± ± ± ± 1 PLACE 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2018/04/04 10 INCH ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:36:29 9 8 7 6 5 ° EC NO: 174360 DRWN: PSWAMI02 CHK'D: PSWAMI02 APPR: AROBERTSON INITIAL REVISION: DRWN: PSWAMI02 APPR: AROBERTSON THIRD ANGLE PROJECTION 4 2018/04/04 2018/04/04 2018/04/04 SMA JACK, 2H FLG WITH 0-80 THD, 50 OHM 27 GHZ SMA-JR/F, EWR-10959-A PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2017/06/01 2017/06/01 DRAWING SERIES C-SIZE 73251 3 A DOC TYPE DOC PART REVISION SD-73251-185 MATERIAL NUMBER CUSTOMER PSD 000 B21 SHEET NUMBER SEE TABLE 1 OF 3 2 1 12 11 10 9 8 7 5 6 4 3 2 1 MATERIALS AND FINISHES H SEE SHEET 1 H PCB LAYOUT SEE SHEET 1 B B PCB RANGE SEE TABLE G .218 MIN 5.54 +.000 -.031 .00 A -.79 SCREW LENGTH SEE TABLE A G F F ⌀ .116 +.000 -.012 2.95 E 0.00 -0.30 E 0-80 UNF-2A THREAD TORQUE TO .5-.8 INCH-POUNDS +.002 -.006 +0.05 1.06 -0.15 .042 D C B D 73251-1856 73251-1855 73251-1854 73251-1853 73251-1852 73251-1851 73251-1850 PART NO. 4.76 / .188 3.18/ .125 9.53/ .375 6.35/ .250 N/A 4.76/ .188 N/A (MM/IN) DIM A .062+.040/-.01 1.57+1.02/-.25 .050+.00/-.040 1.27+0.00/-1.02 .255+.040/-.02 6.48+1.02/-.51 .130+.040/-.02 3.30+1.02/-.51 N/A N/A .062+.040/-.01 1.57+1.02/-.25 N/A N/A IN MM DIM B 2 2 2 2 NO SCREW 2 NO SCREW SINGLE BAG TRAY TRAY TRAY SINGLE BAG TRAY TRAY IN BAG BULK BULK BULK NONE BULK NONE SCREWS (QTY) PACKAGING SCREW PACKAGING C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE CURRENT REV DESC: SEE ECM 117632 DIMENSION UNITS INCH GENERAL TOLERANCES (UNLESS SPECIFIED) MM A 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± ± ± ± 1 PLACE 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2018/04/04 10 INCH ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:36:29 9 8 7 6 5 ° EC NO: 174360 DRWN: PSWAMI02 CHK'D: PSWAMI02 APPR: AROBERTSON INITIAL REVISION: DRWN: PSWAMI02 APPR: AROBERTSON THIRD ANGLE PROJECTION 4 2018/04/04 2018/04/04 2018/04/04 SMA JACK, 2H FLG WITH 0-80 THD, 50 OHM 27 GHZ SMA-JR/F, EWR-10959-A PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2017/06/01 2017/06/01 DRAWING SERIES C-SIZE 73251 3 A DOC TYPE DOC PART REVISION SD-73251-185 MATERIAL NUMBER CUSTOMER PSD 000 B21 SHEET NUMBER SEE TABLE 2 OF 3 2 1 12 11 10 9 8 7 5 6 4 3 2 1 ADDITIONAL APPLICATION NOTES / ASSEMBLY INSTRUCTIONS H H 1. SEE SHEET ONE FOR SUGGESTED PCB LAYOUT. HEIGHT OF GROUND AND SIGNAL PADS MUST BE EVEN WITHIN ±.0015(.038). G G 2. SECURE CONNECTOR TO BOARD BY THREADING TWO 0-80 SCREWS FROM BOTTOM SIDE OF BOARD THROUGH CONNECTOR HOLES TO INDICATED TORQUE (SEE FIGURE). PCB DO NOT SOLDER CONNECTOR TO BOARD. F F TORQUE SCREWS TO .5 - .8 INCH-POUNDS TWO PLACES E E D D .218 MIN 5.54 MOUNTING SCREW MUST NOT EXTEND BEYOND THIS POINT C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE CURRENT REV DESC: SEE ECM 117632 DIMENSION UNITS INCH GENERAL TOLERANCES (UNLESS SPECIFIED) MM A 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± ± ± ± 1 PLACE 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2018/04/04 10 INCH ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:36:29 9 8 7 6 5 ° EC NO: 174360 DRWN: PSWAMI02 CHK'D: PSWAMI02 APPR: AROBERTSON INITIAL REVISION: DRWN: PSWAMI02 APPR: AROBERTSON THIRD ANGLE PROJECTION 4 2018/04/04 2018/04/04 2018/04/04 SMA JACK, 2H FLG WITH 0-80 THD, 50 OHM 27 GHZ SMA-JR/F, EWR-10959-A PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2017/06/01 2017/06/01 DRAWING SERIES C-SIZE 73251 3 A DOC TYPE DOC PART REVISION SD-73251-185 MATERIAL NUMBER CUSTOMER PSD 000 B21 SHEET NUMBER SEE TABLE 3 OF 3 2 1