0732512209

12 10 11 9 7 8 5 6 4 SQ .276 ±.006 7.00 ±0.15 H BODY, JAM NUT: BRASS 1. VOLTAGE STANDING WAVE RATIO 1.1(MAX) @0-6GHz. FINISH: SEE TABLE H .450 ±.006 11.43 ±0.15 1.8(MAX) @12-18GHz. PLATED GOLD 1 .650 ±.012 16.50 ±0.30 1.5(MAX) @6-12GHz. CENTER CONTACT: BERYLLIUM COPPER 2 .770 ±.010 19.55 ±0.25 ELECTRICAL REQUIREMENTS: MATERIALS AND FINISHES: 3 2. RF INSERTION LOSS: 0.1(MAX) @0-6GHz. 0.4(MAX) @6-12GHz. INSULATOR: TEFLON G G .411 ±.006 10.44 ±0.15 0.7(MAX) @12-18GHz. LOCKWASHER: PHOSPHOR BRONZE .250 ±.006 6.35 ±0.15 FINISH: SEE TABLE SMA JACK INTERFACE F .240 6.10 MIN .059 ⌀ 1.50 MIN 5 PLACES E .100 2.54 TYP F 1/4-36 UNS-2A .039 ±.004 1.00 ±0.10 SQ 4 PLACES .256 ⌀ 6.50 .200 5.08 TYP .020 ±.006 0.50 ±0.15 DIM A ±0.006 DIM A ±0.15 .050 ±.002 ⌀ 1.27 ±0.05 E SEE SD-73251-496 FOR PART NO. CONTINUATION RECOMMENDED PCB LAYOUT RECOMMENDED PANEL CUTOUT D .315 ±.008 8.00 ±0.20 HEX .076 ±.008 1.93 ±0.20 .020 ±.008 0.50 ±0.20 C 73251-2209 GOLD FLASH / STANDARD TRAY 3.94 .155 73251-2208 GOLD FLASH/STANDARD TRAY W/O WASHER AND NUT 3.94 .155 73251-2207 73251-2201 PACKAGED ONE PER BAG 2.79 .110 73251-2206 SAME AS 73251-2201 EXCEPT COMMERCIAL CONTACT 2.79 .110 73251-2205 SAME AS 73251-2200 EXCEPT COMMERCIAL CONTACT 2.79 .110 73251-2204 GOLD FLASH/STANDARD TRAY W/O WASHER AND NUT 2.79 .110 73251-2203 GOLD FLASH / STANDARD TRAY (54 CAVITY) 2.79 .110 73251-2202 73251-2201 PACKAGED IN SMALL TRAY (20 CAVITY) 2.79 .110 73251-2201 GOLD / STANDARD TRAY 2.79 .110 73251-2200 NICKEL / STANDARD TRAY 2.79 .110 PLATING (BODY, NUT, LOCKWASHER) AND PACKAGING PART NO. B DIM A .378 ±.008 ⌀ 9.60 ±0.20 JAM NUT FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: ADD SLODER SPEC NO. PER EWR14716-B = LOCKWASHER = PS-89675-368 SOLDER SPEC PROFILE PS-89675-346 ELECTRO/MECH PERFORM. SPECIFICATION DESCRIPTION DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/08/26 10 0 0 mm NTS GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± = A C IN mm B D 0 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:31:44 9 8 7 6 5 EC NO: 675413 DRWN: CWEI02 CHK'D: YCHENG APPR: YCHENG INITIAL REVISION: DRWN: AROBERTSON APPR: JWIENER THIRD ANGLE PROJECTION 4 2021/08/24 2021/08/26 2021/08/26 SMA JACK, R/A PCB 50 OHM SMA-J/RA/PCB EWR-2144 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/11/21 2012/11/21 DRAWING SERIES C-SIZE 73251 3 SD-73251-220 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 D14 SHEET NUMBER 1 OF 1 1 A