0732513482

12 11 10 9 7 8 5 6 4 3 2 1 MATERIALS AND FINISHES: H BODY: STAINLESS STEEL PLATED: PASSIVATE H .376 REF 9.54 CENTER CONTACT: BERYLLIUM COPPER PLATED: GOLD (50µ-in) MIN OVER NICKEL (100µ -in) MIN .223 REF 5.66 .065 REF 1.65 1/4-36 UNS-2A INSULATOR: PTFE GROUNDING RING G C SCREW: STAINLESS STEEL PLATED: PASSIVATE G D SMA JACK INTERFACE F ⌀ .394 REF ⌀ .282 REF 10.00 7.16 F .218 5.54 MIN 0-80 UNF 2 PLACES MOUNTING SCREWS MUST NOT EXTEND BEYOND THIS POINT E ⌀ .063 ±.001 ⌀ .030 ±.003 0.76 ±0.08 SIGNAL PAD .0025 REF 0.064 ⌀ .170 REF GROUND PAD D E 1.600 ±0.025 2 PLACES THRU ⌀ .088 REF ⌀ .020 ±.001 4.32 GROUND PAD MINIMUM 2.24 INSULATOR OUTER DIAMETER 0.508 ±0.025 CENTER CONTACT .282 ±.002 7.16 ±0.05 SIGNAL PAD C 4.32 GROUNDING RING OUTER DIAMETER D ⌀ .101 ±.002 2.57 ±0.05 GROUND PAD .141 ±.002 3.58 ±0.05 2 PLACES ⌀ .170 REF ⌀ .101 REF ⌀ .037 REF GENERAL PCB LAYOUT DETAIL D 0.94 INSULATOR INNER DIAMETER +.003 .005 -.000 +0.08 0.13 -0.00 CONTACT 2.57 GROUNDING RING INNER DIAMETER DETAIL C C SEE SHEET 2 FOR PART NUMBERS PS-89675-3460 ELECTO/MECH PERFOR MIL-STD-348B, FIG 310-2 SMA JACK INTERFACE B SPECIFICATION DESCRIPTION B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE CURRENT REV DESC: SEE ECR DIMENSION UNITS INCH NTS GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± A 1 PLACE 0.25 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2019/03/15 10 INCH ± ± ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:32:57 9 8 7 6 5 0.01 2.0 ° EC NO: 613729 DRWN: LMEIER CHK'D: SSSHAH APPR: AROBERTSON INITIAL REVISION: DRWN: APRAKASH01 APPR: AROBERTSON THIRD ANGLE PROJECTION 4 2019/03/12 2019/03/15 2019/03/15 SMA JACK, FLANGE WITH 0-80 THD, 50 OHM 27 GHZ SMA-J/R/F, EWR-10959 PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2016/10/21 2017/02/21 DRAWING SERIES C-SIZE 73251 3 A DOC TYPE DOC PART REVISION SD-73251-348 MATERIAL NUMBER CUSTOMER PSD 000 A13 SHEET NUMBER SEE TABLE 1 OF 2 2 1 12 11 10 9 7 8 5 6 4 3 2 1 MATERIALS AND FINISHES: SEE SHEET 1 PCB LAYOUT: SEE SHEET 1 H H G .218 5.54 MIN +.000 A -.031 .00 A -.79 SCREW LENGTH SEE TABLE F +.002 -.006 +0.05 1.06 -0.15 G .042 ⌀ .116 +.000 -.012 2.95 E B B PCB RANGE SEE TABLE F 0.00 -0.30 E 0-80 UNF-2A THREAD TORQUE TO .5-.8 lb-in D D FOR ADDITIONAL APPLICATION NOTES SEE SHEET 3 OF SD-73251-185 C C 73251-3485 73251-3484 73251-3483 73251-3482 73251-3481 73251-3480 B PART NO. .125/3.18 .375/9.52 .250/6.35 N/A .188/4.76 N/A (IN/MM) DIM A .050+.00/-.040 1.27+0.00/-1.02 .255+.040/-.02 6.48+1.02/-.51 .130+.040/-.02 3.30+1.02/-.51 N/A N/A .062+.040/-.01 1.57+1.02/-.25 N/A N/A IN MM DIM B 2 2 2 NO SCREW 2 NO SCREW TRAY TRAY TRAY SINGLE BAG TRAY TRAY BULK BULK BULK NONE BULK NONE SCREWS (QTY) PACKAGING SCREW PACKAGING B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE CURRENT REV DESC: SEE ECR DIMENSION UNITS INCH NTS GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± A 1 PLACE 0.25 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2019/03/15 10 INCH ± ± ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:32:57 9 8 7 6 5 0.01 2.0 ° EC NO: 613729 DRWN: LMEIER CHK'D: SSSHAH APPR: AROBERTSON INITIAL REVISION: DRWN: APRAKASH01 APPR: AROBERTSON THIRD ANGLE PROJECTION 4 2019/03/12 2019/03/15 2019/03/15 SMA JACK, FLANGE WITH 0-80 THD, 50 OHM 27 GHZ SMA-J/R/F, EWR-10959 PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2016/10/21 2017/02/21 DRAWING SERIES C-SIZE 73251 3 A DOC TYPE DOC PART REVISION SD-73251-348 MATERIAL NUMBER CUSTOMER PSD 000 A13 SHEET NUMBER SEE TABLE 2 OF 2 2 1