0747280002

20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 MM 3D MODEL:747280002 PSM ASY M L L LIGHT PIPES SECURED TO METAL COVER K K 53.2 J J H H COVER DESIGNED TO SNAP ON THE SFP CAGE ASSEMBLY LIGHT PIPES MOLDED WITH V0 RATED MATERIAL G G 58.0 F ⌀1.78 TYP 3.2 4X 5.84 3X 14.25 45.2 7.1 7.1 TYP. WEEK/YEAR DATE CODE TABLE WK WEEK OF THE YEAR 01 THRU 52 (EXAMPLE: 01= FIRST WEEK OF YEAR 52= LAST WEEK OF YEAR) YR 19,20,21,,ETC (EXAMPLE: YEAR 2019= 19) D NOTES: 1. THIS LIGHT PIPE ASSEMBLY TO BE USED WITH SERIES 74728, 1X4 CAGES. 2. IT IS RECOMMENDED THAT THE CAGE ASSEMBLY BE PRESSED INTO OR SOLDERED TO THE PCB PRIOR TO ASSEMBLING THE LIGHT PIPE ASSEMBLY. 3. LED'S TO HAVE A MAXIMUM HEIGHT OF 1.4mm AND A MINIMUM HEIGHT OF 0.7mm 4. RECOMMENDED LED'S INCLUDE THE FOLLOWING MANUFACTURES: DIALIGHT: 597-77x1-5xx SERIES CHICAGO MINIATURE: 7016 SERIES KINGBRIGHT: APBL3025 SERIES (BICOLOR) APL3015 SERIES (SINGLE COLOR) 5. NO RoHS EXEMPTIONS. 6. DISCOLORATION IS NOT ALLOWED. 20 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 RELEASE DATE 18 2019/06/06 17 SYMBOLS = 0 = 0 = 0 C 15 14 13 12 11 10 9 8 SCALE mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 = 0 D THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS ANGULAR TOL = 0 08:41:03 16 PART NO. AND WEEK/YEAR DATE CODE TO BE PRINTED ON BACK OF COVER APPROXIMATELY AS SHOWN. SEE TABLE BELOW FOR DATE CODE INFORMATION. 4.7 57.3 DOCUMENT STATUS E 3.6 2.5 TYP. A 747280002WKYR 1.8 ±0.2 E B F 5 REF 12.2 4.6 C LIGHT PIPE NOT SHOWN FOR CLARIFY 4.1 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 7 CURRENT REV DESC: SEE REVISION TABLE EC NO: 618645 DRWN: JYEN01 CHK'D: JCHIANG APPR: JCHIANG INITIAL REVISION: DRWN: PMAHADEVAPPA APPR: RCHEN08 THIRD ANGLE PROJECTION 6 2019/06/06 2019/06/06 2019/06/06 2018/12/18 2019/01/15 DRAWING SERIES D-SIZE 74728 5 1X4 SFP LIGHT PIPE COVER ASSEMBLY, LOW PROFILE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 747280002 MATERIAL NUMBER PSD ASY B1 SHEET NUMBER CUSTOMER 747280002 4 B 1 OF 5 3 2 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PCB LAYOUT FOR BELLY TO BELLY MOUNTING 0.00 L CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) K 58.00 L B 11.93 57.00 42.75 SEE NOTE 4 28.50 SEE NOTE 4 11.08 14.25 7.13 8.57 3.17 5.68 3.75 2.33 1.00 HOST CONNECTOR DETAIL TOP LEFT HOLE OF ADJACENT CAGE A K 10.93 SEE NOTE 4 0.00 4.50 J J 9.50 H 14.50 56X ⌀1.05 ±0.05 14.50 10 TYP 19.50 ⌖ 0.1 A B H 1 4.10 8.20 11 20 G G 24.50 27.30 29.50 24X ⌀0.95 ±0.05 F ⌖ 0.1 A B 18X 0.80 32.00 SMALLER HOLE ON THESE FOUR ROWS ONLY 1.00 F 10.53 35.40 9.60 37.00 11.93 39.50 E E DETAIL 1 SCALE 8:1 41.60 42.30 3.56 8X ⌀1.55 D 46.40 D ⌖ 0.1 A B 2.54 6.50 TYP. THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) C 2.00 TYP. SEE DETAIL 1 RECOMMENDED CENTRIX OF LED THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SYMBOLS AREA OF LIGHT PIPE COVERAGE 2.88 TYP. = 0 = 0 NOTES: 1. PADS AND VIAS GO TO CHASSIS GROUND, (64 PLACES). RECOMMENDED PADS TO BE 2mm SQUARE. 2. PLATING OPTIONAL FOR THROUGH HOLES, (16 PLACES). 3. RECOMMENDED PLATING INCLUDES HASL, IMMERSION (GOLD OR SILVER), AND OSP. 4. HOLE PATTERN REPEATS FOR EACH PORT, SPACING BETWEEN PORTS IS 14.25. B = 0 DOCUMENT STATUS 20 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 RELEASE DATE 18 2019/06/06 17 16 C 15 14 13 12 11 10 9 8 mm 6:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 08:41:03 SCALE ANGULAR TOL = 0 A DIMENSION UNITS = 0 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 7 C CURRENT REV DESC: SEE REVISION TABLE EC NO: 618645 DRWN: JYEN01 CHK'D: JCHIANG APPR: JCHIANG INITIAL REVISION: DRWN: PMAHADEVAPPA APPR: RCHEN08 THIRD ANGLE PROJECTION 6 2019/06/06 2019/06/06 2019/06/06 2018/12/18 2019/01/15 DRAWING SERIES D-SIZE 74728 5 1X4 SFP LIGHT PIPE COVER ASSEMBLY, LOW PROFILE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 747280002 MATERIAL NUMBER PSD ASY B1 SHEET NUMBER CUSTOMER 747280002 4 B 2 OF 5 3 2 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PCB LAYOUT FOR SINGLE SIDE MOUNTING 0.00 B L L 11.93 58.00 57.00 42.75 28.50 SEE NOTE 4 SEE NOTE 4 14.25 11.08 7.13 8.58 5.68 3.75 2.33 1.00 A SEE NOTE 4 0.00 K CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) K 4.50 J J 9.50 14.50 H H 30X ⌀1.05 ±0.05 19.50 ⌖ 0.1 A B 24.50 G G 27.30 29.50 16X ⌀0.95 ±0.05 32.00 ⌖ 0.1 A B F SMALLER HOLE ON THESE FOUR ROWS ONLY F 35.40 37.00 39.50 41.60 E 42.30 8X ⌀1.55 ⌖ 0.1 A B 3.56 46.40 SEE SHEET 2 FOR HOST CONNECTOR DETAIL D THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) 6.50 TYP. 2.54 C SYMBOLS NOTES: 1. PADS AND VIAS GO TO CHASSIS GROUND, (34 PLACES). RECOMMENDED PADS TO BE 2mm SQUARE. 2. PLATING OPTIONAL FOR THROUGH HOLES, (12 PLACES). 3. RECOMMENDED PLATING INCLUDES HASL, IMMERSION (GOLD OR SILVER), AND OSP. 4. HOLE PATTERN REPEATS FOR EACH PORT, SPACING BETWEEN PORTS IS 14.25. = 0 = 0 = 0 DOCUMENT STATUS 20 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 RELEASE DATE 18 2019/06/06 17 08:41:03 16 C 15 14 13 12 11 10 9 8 SCALE mm 6:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS ANGULAR TOL = 0 = 0 D RECOMMENDED CENTRIX OF LED AREA OF LIGHT PIPE COVERAGE 2.00 TYP. 2.88 TYP. B E 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 7 CURRENT REV DESC: SEE REVISION TABLE EC NO: 618645 DRWN: JYEN01 CHK'D: JCHIANG APPR: JCHIANG INITIAL REVISION: DRWN: PMAHADEVAPPA APPR: RCHEN08 THIRD ANGLE PROJECTION 6 2019/06/06 2019/06/06 2019/06/06 2018/12/18 2019/01/15 DRAWING SERIES D-SIZE 74728 5 1X4 SFP LIGHT PIPE COVER ASSEMBLY, LOW PROFILE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 747280002 MATERIAL NUMBER PSD ASY B1 SHEET NUMBER CUSTOMER 747280002 4 B 3 OF 5 3 2 1 A 20 19 18 17 16 15 14 13 M 11 10 9 4X 5.84 L 7 8 5 6 4 3 2 1 M BEZEL AND BOARD POSITION DIMENSIONS FOR SINGLE SIDE MOUNTING 3X 14.25 8X ⌀2.54 12 1.20 8.03 45.2 END OF LIGHT PIPE FLUSH WITH BEZEL L 0.25 MIN/1.27 MAX 4.1 13.0 10.77 ±0.10 RECOMMENDED K 13.9 9.65 ±0.18 K 1.7 NOTE: MAX LED HEIGHT OF 1.40 0.25 MIN/1.27 MAX J 2.75 A R0.3 MAX TYP 24.30 J 3.50 ±0.30 46.4 58.00 ±0.10 1.86 ±0.13 H H BEZEL AND BOARD POSITION DIMENSIONS FOR BELLY TO BELLY MOUNTING 1.86 ±0.13 58.00 ±0.10 3.50 ±0.30 24.30 G 2.75 8X 5.84 G A 8.03 F F 10.77 ±0.10 RECOMMENDED E 0.40 ±0.10 RECOMMENDED BEZEL OPENING BELOW PCB E C ±0.10 0.25 MIN/1.27 MAX B ±0.10 A 10% 0.25 MIN/1.27 MAX D 3X 14.25 D R0.3 MAX TYP 8.03 24.30 C SYMBOLS = 0 NOTE: FOR A GIVEN BOARD THICKNESS (A), DIMENSIONS (B) AND (C) ARE DIRECTLY AFFECTED. USE RECOMMENDED DIMENSIONS AND TOLERANCES TO AID IN DEVELOPING BEZEL OPENING. FOR EXAMPLE USING A BOARD THICKNESS OF 3.18mm THE RECOMMENDED VALUES WOULD BE: A= 3.18 ±10% B= 11.03 ±.10 C= 2.23 ±.10 B A 9.65 ±0.18 DOCUMENT STATUS 20 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 RELEASE DATE 18 2019/06/06 17 = 0 = 0 16 15 14 13 12 11 10 9 8 mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 C SCALE ANGULAR TOL = 0 08:41:03 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS = 0 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 7 CURRENT REV DESC: SEE REVISION TABLE EC NO: 618645 DRWN: JYEN01 CHK'D: JCHIANG APPR: JCHIANG INITIAL REVISION: DRWN: PMAHADEVAPPA APPR: RCHEN08 THIRD ANGLE PROJECTION 6 2019/06/06 2019/06/06 2019/06/06 2018/12/18 2019/01/15 DRAWING SERIES D-SIZE 74728 5 1X4 SFP LIGHT PIPE COVER ASSEMBLY, LOW PROFILE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 747280002 MATERIAL NUMBER PSD ASY B1 SHEET NUMBER CUSTOMER 747280002 4 B 4 OF 5 3 2 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L L K J DATE REV 2005/11/05 2018/12/18 A B 2019/06/06 B1 K DESCRIPTION INITIAL RELEASE 1. REMASTERED FROM SD-74728-002 REV_A TO 747280002 PSD ASY REV_B IN NX/ECTR. 2. REMOVED INCH DIMENSIONS IN ALL SHEETS. 3. SHEET 1: E4: VIEW ADDED FOR DATE CODE REPRESENTATION. SHEET 1: ADDED "DISCOLORATION IS NOT ALLOWED" TO NOTE 6. J H H G G F F E E D D C C SYMBOLS = 0 = 0 B = 0 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2019/06/06 16 08:41:03 C 15 14 13 12 11 10 9 8 mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 DOCUMENT STATUS SCALE ANGULAR TOL = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 7 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: SEE REVISION TABLE B EC NO: 618645 DRWN: JYEN01 CHK'D: JCHIANG APPR: JCHIANG INITIAL REVISION: DRWN: PMAHADEVAPPA APPR: RCHEN08 THIRD ANGLE PROJECTION 5 1X4 SFP LIGHT PIPE COVER ASSEMBLY, LOW PROFILE 2019/06/06 2019/06/06 2019/06/06 2018/12/18 2019/01/15 DRAWING SERIES D-SIZE 74728 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 747280002 MATERIAL NUMBER PSD ASY SHEET NUMBER CUSTOMER 747280002 3 B1 5 OF 5 2 1 A