0747320220

20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 M L 2 1 M 0.098 X4 2.50 0.035 0.89 EMI GASKET FOR FRONT PANEL. THE EMI GASKET MATERIAL IS A ROUND, COMPLIANT, CONDUCTIVE ELASTOMER THAT STRETCHES AROUND THE MOUTH OF THE XPAK RAIL. A BEZEL LOCATED PER THE XPAK MSA WILL MAKE GROUNDING CONTACT WITH THE GASKET TO 1.669 1.597 1.497 PROVIDE EMI SHIELDING. 42.40 40.56 38.02 3 0.197 X4 5.00 L 1.367 1.437 34.72 36.50 3 3 K K 1.657 42.09 EMI GASKET TO PCB 0.20 MILLED (REMOVED) FROM THIS SURFACE 1.437 36.5 J 0.626 15.902 H 0.8° 0.040 1.02 0.143 3.63 0.286 7.26 G SEE DETAIL Z 0.580 14.74 0.160 4.06 0.000 0.00 0.406 10.31 0.032 X4 0.80 EMI GASKET 0.030 0.76 0.125 3.17 0.036 X2 0.924 0.118 X8 3.00 F 0.285 7.25 E DETAIL Z SCALE 8:1 0.110 2.80 MOLEX P/N 747320221 747320222 747320223 ALL DIMENSIONS FOR LATCHING HOLE MIRRORED ON OTHER SIDE D C 0.170 4.32 0.250 6.35 0.049 X8 3.93 1.25 1.250 31.75 0.750 19.05 G 1.750 44.45 F 0.028 X2 0.70 DESCRIPTION XPAK RAIL ASSEMBLY - WITH ONE MILLED SIDE AND 0.078 ELASTOMER GASKET XPAK RAIL ASSEMBLY - WITH ONE MILLED SIDE AND 0.098 ELASTOMER GASKET XPAK RAIL ASSEMBLY - WITH ONE MILLED SIDE AND 0.090 ELASTOMER GASKET 1.359 34.52 1.500 38.10 0.215 5.46 1. MATERIAL: NICKEL PLATED ZINC ALLOY DIECAST 2. FOR USE WITH HASL, GOLD OR SILVER IMMERSION FINISHED PTH 3. THESE DIMENSIONS EXCEED MSA MAXIMUM. 4. MINIMUM PCB THICKNESS FOR PRESS FIT ON ONE SIDE 0.062 [1.57] 5. MINIMUM PCB THICKNESS FOR BELLY TO BELLY 0.090 [2.29] 1.597 40.56 E 1.762 44.75 1.928 48.98 ⌀ 0.084 ±0.0015 X8 2.010 51.05 2.13 ±0.04 ⌖ 0.006 A B 2 0.155 1.500 38.10 1.000 25.40 0.500 12.70 B 0.166 4.229 SECTION A-A SCALE 4:1 H 2.942 74.74 A c 0.035 0.88 0.466 11.84 0.566 14.38 A 0.070 1.78 1.78 J A 1.938 49.23 ⌀ .0700 X4 R 0.031 X4 0.80 0.0200 0.51 D 2.453 62.31 2.561 65.05 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE IN/MM 2:1 CURRENT REV DESC: OBSOLETED PART NO GENERAL TOLERANCES (UNLESS SPECIFIED) MM 0.018 0.46 B R 0.035 0.89 0.035 0.89 4 PLACES ± ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/11/12 17 ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:19:25 16 0.01 ± ANGULAR TOL A INCH 15 14 13 12 11 10 9 8 7 EC NO: 625872 DRWN: VLOKESHA CHK'D: GB APPR: GGA INITIAL REVISION: DRWN: KLLOYD APPR: BRUSSELL THIRD ANGLE PROJECTION 6 2019/08/13 2019/11/06 2019/11/12 XPAK GUIDE RAIL ASSEMBLY (SALES) W/ MILLED SIDE B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2002/05/01 2002/05/01 DRAWING SERIES D-SIZE 74732 5 SD-74732-221 MATERIAL NUMBER GENERAL MARKET 3 F1 SHEET NUMBER CUSTOMER SEE CHART 4 PSD 001 2 1 OF 2 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M L L 2.00 ±0.08 K 1.333 33.85 ⌖ ⌀0.006 D E R 0.030 TPY. 0.76 B ADJACENT RAIL HOLE PATTERN SHOWN AT MIN SPACING K F 1.540 39.12 1.698 43.14 1.500 38.10 H 1.250 31.75 1.000 25.40 0.30 7.6 0.750 19.05 0.500 12.70 1.75 44.5 EMI GASKET CONTACT SURFACES (SHOWN WITHOUT EMI GASKET) G 0.250 6.35 0.000 0.00 0.252 6.40 B 1.929 49.00 1.750 44.45 G 1 ⌖ 0.010 F J 2.200 55.88 H HATCHED AREA CHASSIS GROUND 2.598 66.00 2.455 62.36 J 1.650 MIN. 41.91 1.652 41.96 ⌀ 0.079 ±0.003 PTH X 8 0.506 12.85 FLAT PRESS PLATE 0.062 MIN. 1.57 0.149 3.79 F 0.051 1.30 D E ⌀ 0.104 X4 0.028 X2 0.70 2.64 F 2 ⌖ ⌀0.010 D E 0.051 X2 1.30 .360 MAX. 9.15 1.449 X2 36.81 E 0.149 ±0.015 3.79 ±0.38 .215 REF. 5.46 0.260 ±0.015 6.61 ±0.38 1.500 X4 38.10 2.821 71.66 1.528 X2 38.80 D E D SECTION B-B 1.551 39.40 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C 1. SEE DRAWING SD-74441-001 FOR HOST CONNECTOR LAYOUT DETAIL. 2. THESE HOLES CAN BE OMITTED, THEY ARE NOT NEEDED FOR THIS RAIL VERSION. 3. PLATED HOLES CAN BE HASL, GOLD OR SILVER IMMERSION. 4. PCB LAYOUT SHOWN IS FOR SINGLE SIDED MOUNTING ONLY. 5. BELLY TO BELLY MOUNTING REQUIRES ABOVE LAYOUT MIRRORED ON OPPOSITE SIDE OF PCB AND THE SECONDARY BEZEL OPENING MUST ACCOMODATE THE PCB THICKNESS VARIATION. B DIMENSION UNITS SCALE IN/MM 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/11/12 17 ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:19:25 16 0.01 ± ANGULAR TOL DOCUMENT STATUS INCH 4 PLACES ± 1 PLACE A CURRENT REV DESC: OBSOLETED PART NO 15 14 13 12 11 10 9 8 7 EC NO: 625872 DRWN: VLOKESHA CHK'D: GB APPR: GGA INITIAL REVISION: DRWN: KLLOYD APPR: BRUSSELL THIRD ANGLE PROJECTION 6 2019/08/13 2019/11/06 2019/11/12 XPAK GUIDE RAIL ASSEMBLY (SALES) W/ MILLED SIDE B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2002/05/01 2002/05/01 DRAWING SERIES D-SIZE 74732 5 SD-74732-221 MATERIAL NUMBER GENERAL MARKET 3 F1 SHEET NUMBER CUSTOMER SEE CHART 4 PSD 001 2 2 OF 2 1 A