0747370009

12 11 10 3D MODEL: 747370009 PSM ASY 9 7 8 5 6 4 3 2 1 SPRING FINGER GASKET WITH TWO POINTS OF CONTACT. COMPLIES WITH (SFP) MSA BOARD AND BEZEL LOCATIONS. 14.00 H H 14.98 3X 0.25 +0.20 -0.05 DETAIL A G G TABS USED TO MOUNT LIGHT PIPE COVER CAGE IDENTIFICATION LAST 2 DIGITS P/N AND REV LETTER (ex: 09 X) F DETAIL A SCALE 10:1 F ONE PIECE DESIGN SECURELY FASTENED E E 14.50 48.73 14.00 D 8.58 9.15 D 9.65 9.70 C C 3.05 TYP 11.50 B B NOTES: FORMAT: tb-prod-C REVISION: G DATE: 2015/12/14 12 P1 RELEASE DATE 11 15.05.2017 10 2017/04/06 2017/05/11 2017/05/15 SEE REVISION TABLE D 06:09:50 9 8 7 6 5 REV RELEASE STATUS DRWN BY ANGULAR TOL ± 1.0 ° 116814 PGSHETTY DSUN15 RCHEN08 1. PRESS FIT LEGS, 0.120 INCHES LONG 1.57 MINIMUM PCB THICKNESS. 2. THIS CAGE IS FOR SINGLE SIDED USE ONLY. 3. CAN BE USED WITH THE FOLLOWING LIGHT PIPE PART NUMBERS: 747260001 - LIGHT PIPE FROM BACK TO TOP REFER TO DOCUMENT SD-747260001 747260002 - LIGHT PIPE FROM SIDE TO TOP REFER TO DOCUMENT SD-747260002 4. MATERIAL: COPPER ALLOY PLATING: PRE-PLATED WITH NICKEL 5. NO RoHS EXEMPTONS EC NO: DRWN: CHK'D: APPR: A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 3.5:1 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2017/04/06 PGSHETTY CHK'D BY DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE 2017/05/11 DSUN15 APPR BY DATE 2017/05/15 RCHEN08 DRAWING SIZE SFP ONE PIECE CAGE PRESS-FIT (0.120 LEGS) DATE THIRD ANGLE PROJECTION C PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 74737 747370009 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 747370009 3 CUSTOMER 2 PSD 1 OF 4 ASY 1 A 12 11 10 9 8 7 16.25 4 3 2 1 PCB LAYOUT FOR SINGLE SIDE MOUNT 14.25 H 5 6 11.08 H Y.YY 8.58 2 11X 2.00 Y 5.68 CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) 1 X 1 10.93 B 9.60 G G 20X 0.50 ⌖ 0.06 A B 0.80 TYP 2.00 TYP ⌖ 0.06 A B 10.00 F 26.80 42.30 10.00 2 11X 2.00 F 10X ⌀ 1.05 ±0.05 2 (SHOWN AS ) ⌖ ⌀0.1 X A 34.50 10.00 41.30 PIN 10 3.20 PIN 1 E E 10.00 0.90 5.00 PIN 20 PIN 11 10.00 7.20 D 2.50 10.00 D 2.50 5.00 2X ⌀ 1.55 ±0.05 ⌖ ⌀0.1 A B 7.10 1.70 1.70 3.68 8.48 C THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) B 11.93 DETAIL 1 SCALE 6:1 SEE DETAIL 1 9.60 9X ⌀ 0.95 ±0.05 (SHOWN AS ) ⌖ ⌀0.1 X A 10.53 ⌀ 0.85 ±0.05 ⌖ ⌀0.1 X Y A 2 4.80 C B HOST CONNECTOR DETAIL 11.93 FORMAT: master-tb-prod-C REVISION: G DATE: 2015/12/14 12 P1 RELEASE DATE 11 15.05.2017 06:09:50 10 9 8 7 6 5 2017/04/06 2017/05/11 2017/05/15 D REV RELEASE STATUS 116814 PGSHETTY DSUN15 RCHEN08 DATUM AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. PADS AND VIAS ARE CHASSIS GROUND. HOLE LAYOUT SHOWN IS FOR SINGLE SIDED MOUNTING ONLY. CONNECTOR PAD LAYOUT PER SFP MSA, WILL ACCOMODATE MOLEX CONNECTOR SERIES 74441 OR EQUIVALENT. DRWN BY ANGULAR TOL ± 1.0 ° EC NO: DRWN: CHK'D: APPR: A 1 2 3 4. SEE REVISION TABLE THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 5:1 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2017/04/06 PGSHETTY CHK'D BY DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE 2017/05/11 DSUN15 APPR BY DATE 2017/05/15 RCHEN08 DRAWING SIZE SFP ONE PIECE CAGE PRESS-FIT (0.120 LEGS) DATE THIRD ANGLE PROJECTION C PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 74737 747370009 DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 747370009 2 PSD ASY 1 2 OF 4 A 12 11 10 9 8 7 6 5 4 H 3 2 1 H 45.23 REF 9.74 G G F F E E R 0.30 MAX TYP 16.25 MIN 3.50 ±0.30 B D D 10.40 ±0.10 B C 0.30 ±0.10 BEZEL OPENING BELOW PCB 15.25 ±0.10 C SECTION B-B B B 2017/04/06 2017/05/11 2017/05/15 RELEASE STATUS FORMAT: master-tb-prod-C REVISION: G DATE: 2015/12/14 12 P1 RELEASE DATE 11 15.05.2017 06:09:50 10 9 8 7 6 5 D REV EC NO: DRWN: CHK'D: APPR: A DRWN BY ANGULAR TOL ± 1.0 ° 116814 PGSHETTY DSUN15 RCHEN08 SEE REVISION TABLE THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 3:1 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2017/04/06 PGSHETTY CHK'D BY DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE 2017/05/11 DSUN15 APPR BY DATE 2017/05/15 RCHEN08 DRAWING SIZE SFP ONE PIECE CAGE PRESS-FIT (0.120 LEGS) DATE THIRD ANGLE PROJECTION C PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 74737 747370009 DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 747370009 2 PSD ASY 1 3 OF 4 A 12 11 10 9 8 7 6 5 4 3 2 1 H H REV DESCRIPTION DATE A 2006/11/30 INITIAL RELEASE B 2007/01/23 [1] CHANGED MODULE EJECT FEATURE TOL FROM +/- 1DEG TO +1/-5DEG; [2] CHANGED EJECT ARM ANGLE TOL FROM +/-1DEG TO 50DEG MIN; [3] CHANGED EMI SPRING FINGER OVERLAP FROM 0.21MM TO 0.01MM MIN; [4] ADDED DIM TO LEGS: OVERALL LENGTH, LENGTH FROM TIP TO SLOT, AND SLOT LENGTH.; [5] DELETED COMMENTS SECTION FROM REV CHART.; [6] ADDED "REF" TO DIM K2 ON SHEET 2. C 2007/04/25 [1] ADDED REV SHEET; [2] UPDATED REV NOTES A-B; [3] UPDATD DRAWING TO REFLECT CHG'S MADE TO EM-74737-009-ASSY REV C; [4] ON SHT1 ROTATED BTM VIEW 180 G G DEGREES. D 2017/04/05 REMASTERED FROM SD-74737-009 REV_C TO 747370009 PSD ASY REV_D IN NX SHEET 2 : F1 : ADDED TYP TO THE DIM 2.00 SHEET 3 : E7 : ADDED DIM R0.3 MAX TYP F F E E D D C C B B 2017/04/06 2017/05/11 2017/05/15 RELEASE STATUS FORMAT: master-tb-prod-C REVISION: G DATE: 2015/12/14 12 P1 RELEASE DATE 11 15.05.2017 06:09:50 10 9 8 7 6 5 D REV EC NO: DRWN: CHK'D: APPR: A DRWN BY ANGULAR TOL ± 1.0 ° 116814 PGSHETTY DSUN15 RCHEN08 SEE REVISION TABLE THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 1:1 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2017/04/06 PGSHETTY CHK'D BY DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE 2017/05/11 DSUN15 APPR BY DATE 2017/05/15 RCHEN08 DRAWING SIZE SFP ONE PIECE CAGE PRESS-FIT (0.120 LEGS) DATE THIRD ANGLE PROJECTION C PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 74737 747370009 DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 747370009 2 PSD ASY 1 4 OF 4 A