0751409012

12 11 10 9 7 8 5 6 4 3 2 1 NOTES: 1) MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER, UL94 V-0 WAFER DIELECTRIC - LIQUID CRYSTAL POLYMER, UL94 V-0 CONTACT - COPPER ALLOY 2) FINISHES: SEE SHEET 2 3) PRODUCT SPECIFICATION THIS PART CONFORMS TO MOLEX SPECIFICATION PS-75018-001 4) PACKAGING SPECIFICATION THIS PART TO BE PACKAGED PER SPECIFICATION PK-75020-005 5) APPLICATION SPECIFICATION THIS PART TO BE APPLIED PER SPECIFICATION AS-75018-001 APPLICATION TOOL AND INSTRUCTIONS PER AS-75018-001 6) MATING INFORMATION THIS PART MATES WITH 75019-XXXX. WILL MATE WITH MAXIMUM 1.27mm MISALIGNMENT. WILL MATE WITH MAXIMUM 0.5° ROTATION MISALIGNMENT. 7) FOR CIRCUIT DESIGNATION SEE SHEET 3 8) FOR PCB INFORMATION SEE SHEET 3 9) CIRCUITS IN THIS ZONE HAVE BEEN OMITTED TO SIMPLIFY THE MODEL. ACTUAL PRODUCT IS FULLY LOADED WITH TERMINALS. 10) APPLICATION TOOLING KEEP OUT AREA. NO COMPONENTS ALLOWED IN THIS AREA. 11) CONFORMS TO MOLEX COSMETIC SPECIFICATION PS-45499-002 AND PS-45499-003 CLASS C. 12) MARKING: PART NUMBER, MOLEX LOGO, DATE CODE (dddy) 13) RECOMMENDED DRILL SIZE 0.66±0.03 TO YIELD FINISHED PLATED THROUGH HOLE 0.55±0.05 H G C(N) F B1 Z B(N) A1 Y C1 A(N) Y E Z SEE NOTE 9 CIRCUIT A1 IDENTIFIER H G F E DIM 'A' TYP DIM 'A' 10.07 TYP .396 DIM 'C' REF DIM 'C' D 13.18 TYP .519 D MARKING SEE NOTE 12 10.68 TYP .420 75140-XXXX molex dddy 2.34 TYP .092 C 7.00 TYP .276 C 5.00 .197 TYP 2.51 TYP .099 1.50 .059 TYP DIM 'B' DIM 'B' B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE MM/INCH 2:1 MM A ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± ANGULAR TOL A DOCUMENT STATUS 12 P1 RELEASE DATE 11 2021/03/16 10 INCH 4 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 CURRENT REV DESC: OBSOLETED PART NUMBER GENERAL TOLERANCES (UNLESS SPECIFIED) 1.80 MINIMUM .071 10.67 REF .420 DIMENSION UNITS 0.01 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:03:16 9 8 7 6 5 EC NO: 655037 DRWN: VLOKESHA CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2021/01/08 2021/03/16 2021/03/16 HIGH SPEED DOCKING VERTICAL FIXED CONNECTOR NO GROUND FINGER PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2009/05/20 2009/05/20 DRAWING SERIES C-SIZE 75140 3 SD-75140-005 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D1 SHEET NUMBER 1 OF 3 1 A 12 11 10 9 7 8 5 6 4 3 2 1 H H ITEM NUMBER G 75140-9012 CIRCUIT SIZE NO. OF COLUMNS 'N' 144 48 O/A LENGTH DIMENSION 'A' mm(in) PEG TO PEG DIMENSION 'B' mm(in) WALL TO WALL DIMENSION 'C' mm(in) FIRST-LAST DIMENSION 'D' mm(in) PLATING FINISH 96.5 (3.80) 87.00 (3.425) 86.32 (3.398) 82.00 (3.228) FINISH 3 G F F E E 1) FINISHES: FINISH 1: (PREVIOUSLY TIN-LEAD) CONTACT INTERFACE 0.76 MICROMETERS MINIMUM SELECT GOLD NICKEL UNDERPLATE OVERALL COMPLIANT INTERFACE 0.76 MICROMETERS MINIMUM SELECT TIN OVER NICKEL UNDERPLATE OVERALL HOUSING 0.10 MICROMETERS MAXIMUM GOLD OVER 3.81 MICROMETERS MINIMUM NICKEL OVER COPPER UNDERPLATE OVERALL D D FINISH 2: CONTACT INTERFACE 0.76 MICROMETERS MINIMUM SELECT GOLD NICKEL UNDERPLATE OVERALL COMPLIANT INTERFACE 0.76 MICROMETERS MINIMUM SELECT MATTE TIN NICKEL UNDERPLATE OVERALL HOUSING 0.10 MICROMETERS MAXIMUM GOLD OVER 3.81 MICROMETERS MINIMUM NICKEL OVER COPPER UNDERPLATE OVERALL C C FINISH 3: CONTACT INTERFACE 0.76 MICROMETERS MINIMUM SELECT GOLD NICKEL UNDERPLATE OVERALL COMPLIANT INTERFACE 0.76 MICROMETERS MINIMUM SELECT MATTE TIN NICKEL UNDERPLATE OVERALL HOUSING 3.81 MICROMETERS MINIMUM NICKEL OVER COPPER UNDERPLATE OVERALL B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/INCH 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM A ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 P1 RELEASE DATE 11 2021/03/16 10 INCH 4 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 CURRENT REV DESC: OBSOLETED PART NUMBER 0.01 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:03:16 9 8 7 6 5 EC NO: 655037 DRWN: VLOKESHA CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2021/01/08 2021/03/16 2021/03/16 HIGH SPEED DOCKING VERTICAL FIXED CONNECTOR NO GROUND FINGER PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2009/05/20 2009/05/20 DRAWING SERIES C-SIZE 75140 3 SD-75140-005 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D1 SHEET NUMBER 2 OF 3 1 A 12 11 10 9 7 8 5 6 4 3 2 1 NO EXPOSED TRACES ON SURFACE OF PCB IN CONNECTOR STAND OFF LOCATIONS H H CONNECTOR KEEP OUT AREA APPLICATION TOOLING KEEP OUT AREAS (NOTES 10 & 11) 8.2 TYP. .32 G CONNECTOR SIDE OF PCB C(N) C1 D2 B1 A1 B(N) 10.9 TYP. A(N) .43 ROW E ROW D B F G 3.50 .138 2.8 TYP. .11 5.5 TYP. .22 0.75 TYP. .030 DIM 'D'- 5.00 REF. DIM 'D'- -.197 1.00 .039 1.80 .071 DIM 'D' REF. DIM 'D' E F 1.50 .059 2.18 TYP. .086 E 1.80 .071 DIM 'B' TYP. DIM 'B' 1.80 .071 C NOTE: DATUM 'C' IS CENTERLINE OF HOLES 4.83 TYP. .190 DIM 'A' ±1.00 TYP. DIM 'A' ±.039 D D CIRCUIT DESIGNATION FIRST MATE: 5.2mm SECOND MATE: 2.7mm THIRD MATE: 2.2mm LAST MATE: 1.7mm .059 ±.002 UNPLATED 0.90 .035 FIRST MATEl HOUSING - SIGNAL GROUND SECOND MATE: A1, C1, A(N) & C(N) (FOR POWER RETURN) THIRD MATE: A2, B2, C2, A(N-1), B(N-1), C(N-1) & ALL OTHERS (A2, C2, A(N-1), & C(N-1) FOR POWER) (ALL OTHERS FOR SIGNAL) LAST MATE: B1 & B(N) (FOR CARD DETECT) NOMINAL WIPE - FULLY MATED C ⌀ 1.50 ±0.05 (2) 0.90 .035 2.00 TYP. .079 5.00 REF. .197 0.57 TYP. .022 ⌀ 0.55 ±0.05 TYP. .022 ±.002 ⌖ ⌀0.10Ⓜ A B C 2.50 REF. .098 ALL COLUMNS FROM 3 THROUGH (N-2) ARE SUITABLE FOR DIFFERENTIAL PAIRS EG.: A3-A4, B3-B4, C3-C4, A(N-2)-A(N-3), B(N-2)-B(N-3) C PLATED SEE NOTE 13 DETAIL X SCALE 5:1 SIGNAL GROUND: ROWS D & E B B 3.39 TYP. -THIRD MATE .133 3.89 TYP. - SECOND MATE .153 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2.89 TYP. - LAST MATE .114 DIMENSION UNITS SCALE MM/INCH 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4.68 REF .184 A SEATING PLANE DOCUMENT STATUS 12 P1 RELEASE DATE 11 ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± ANGULAR TOL SECTION Z-Z 2021/03/16 10 0.01 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:03:16 9 INCH 4 PLACES ± 1 PLACE SECTION Y-Y FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 CURRENT REV DESC: OBSOLETED PART NUMBER 8 7 6 5 EC NO: 655037 DRWN: VLOKESHA CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MIBARRA APPR: SMILLER THIRD ANGLE PROJECTION 4 2021/01/08 2021/03/16 2021/03/16 HIGH SPEED DOCKING VERTICAL FIXED CONNECTOR NO GROUND FINGER PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2009/05/20 2009/05/20 DRAWING SERIES C-SIZE 75140 3 SD-75140-005 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D1 SHEET NUMBER 3 OF 3 1 A