0757051615

12 10 11 9 8 7 5 6 4 3 2 1 75705-* * * * MODULE TYPE -- TAIL PLATING TYPE UNGUIDED -- TIN ONLY = 0 (PREVIOUSLY TIN/LEAD) UNGUIDED -- TIN ONLY = 1 A H B 1.78 3.70 END WALL OPTIONS 0 = OPEN ENDS 1 = LEFT END WALL 2 = DUAL END WALL 3 = RIGHT END WALL # OF COLUMNS 5 = 5 COL 6 = 6 COL 8 = 8 COL 1 = 10 COL G 1.85 PIN LENGTH (P) 2 = 3.90 - 30 GOLD 3 = 4.70 - 30 GOLD 4 = 5.70 - 30 GOLD 5 = 4.70 & 5.70 -30 GOLD STAGGERED 6 = 3.90 - 10 GOLD 7 = 4.70 - 10 GOLD 8 = 5.70 - 10 GOLD 9 = 4.70 & 5.70 - 10 GOLD STAGGERED H G B 24.8 1.00 18.50 3.70 (ADD FOR 1.30 ENDWALL) F 1.35 2.35 PIN A1a F 1.30 (ADD FOR ENDWALL) PIN A1b 2.65 ROW A 3.15 ROW B 1.85 ROW C E E ROW D ROW E 24.8 18.50 ROW F ROW G ROW H ROW J 1.00 ROW K D D ROW L 16.2 P (PIN HEIGHT) ⌖ ⌀0.10 ⌀0.46 ±0.05 PTH (⌀0.57 DRILL) (⌀0.88 PAD) KEEP-OUT ZONE C 2.64 2.1 TAIL LENGTH B A BACKPLANE HOLE PATTERN (CONNECTOR SIDE) (STAGGERED VIEW SHOWN) DOCUMENT STATUS 12 P1 RELEASE DATE 11 2022/02/18 10 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:03:40 9 C 1.60 MINIMUM BOARD NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 10 MICROINCH MINIMUM GOLD OR 30 MICROINCH MINIMUM GOLD IN CONTACT AREA. SELECTIVE MATTE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-75710-999 FOR PERFORMANCE SPECIFICATIONS. 4. FOR MIXED CONTACT MATING LENGTHS, CONSULT MOLEX FOR AVAILABLITY. 5. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 6. PACKAGE PER: PK-70873-587. 7. REFER TO PCB ROUTING GUIDE FOR ANTIPAD AND ROUTING RECOMMENDATIONS. FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 (22 HOLES PER COLUMN) 8 7 6 5 EC NO: 671119 DRWN: YOGEEB CHK'D: MMALLIGEVALU APPR: CWANG25 INITIAL REVISION: DRWN: BPISZCZOR APPR: JLAURX THIRD ANGLE PROJECTION 4 2021/06/17 2021/08/20 2022/02/18 I-TRAC BACKPLANE HEADER UNGUIDED ASSEMBLY SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2006/06/06 2006/06/12 DRAWING SERIES C-SIZE 75705 3 SD-75705-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 1 OF 4 1 A 12 10 11 9 8 MATERIAL NUMBER # OF COLUMNS DIM "A" DIM "B" 75705-*52* 5 21.0 14.80 75705-*62* 6 24.7 18.50 75705-*82* 8 32.1 25.90 75705-*12* 10 39.5 33.30 H 7 6 5 4 3 2 1 H DUAL END WALL STYLE G G MATERIAL NUMBER # OF COLUMNS DIM "A" DIM "B" 75705-*51* 5 19.7 14.80 75705-*61* 6 23.4 18.50 75705-*81* 8 30.8 25.90 75705-*11* 10 38.2 33.30 MATERIAL NUMBER # OF COLUMNS DIM "A" DIM "B" 75705-*53* 5 19.7 14.80 75705-*63* 6 23.4 18.50 75705-*83* 8 30.8 25.90 75705-*13* 10 38.2 33.30 MATERIAL NUMBER # OF COLUMNS DIM "A" DIM "B" 75705-*50* 5 18.35 14.80 75705-*60* 6 22.05 18.50 75705-*80* 8 29.45 25.90 75705-*10* 10 36.85 33.30 F E D C LEFT END WALL STYLE F E RIGHT END WALL STYLE D NOTCH DESIGNATES ROW A C OPEN STYLE B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2022/02/18 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:03:40 9 8 7 6 5 EC NO: 671119 DRWN: YOGEEB CHK'D: MMALLIGEVALU APPR: CWANG25 INITIAL REVISION: DRWN: BPISZCZOR APPR: JLAURX THIRD ANGLE PROJECTION 4 2021/06/17 2021/08/20 2022/02/18 I-TRAC BACKPLANE HEADER UNGUIDED ASSEMBLY SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2006/06/06 2006/06/12 DRAWING SERIES C-SIZE 75705 3 SD-75705-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 2 OF 4 1 A 12 10 11 9 7 8 6 5 4 3 2 1 0.50 H ROW A (FAR SIDE) H 1.00 DCARD PCB ROW A ROW A (NEAR SIDE) G G I-TRAC 11 ROW BOARD RELATIONSHIPS BPLANE PCB SCALE 2:1 CENTERLINE OF HOLE PATTERN COLUMN F 24.8 F 5.2 ORTHOGONAL MIDPLANE HOLE PATTERN (36 SIGNAL PAIRS SHARE VIAS) DCARD PCB E E ROW A 18.1 16.2 BPLANE PCB D DCARD ROW A D 1.20 BPLANE ROW A 2.54 0.60 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 36 PAIR ORTHOGONAL MIDPLANE NODE (USES TWO 6 COLUMN I-TRAC HEADERS) DOCUMENT STATUS 12 P1 RELEASE DATE 11 2022/02/18 10 SCALE mm NTS ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:03:40 9 CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 DIMENSION UNITS 8 7 6 5 EC NO: 671119 DRWN: YOGEEB CHK'D: MMALLIGEVALU APPR: CWANG25 INITIAL REVISION: DRWN: BPISZCZOR APPR: JLAURX THIRD ANGLE PROJECTION 4 2021/06/17 2021/08/20 2022/02/18 I-TRAC BACKPLANE HEADER UNGUIDED ASSEMBLY SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2006/06/06 2006/06/12 DRAWING SERIES C-SIZE 75705 3 SD-75705-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 3 OF 4 1 A 5 19.50 6 4 ⌖ ⌀ 0.10 A1b-L6b A1a-L6a C1b-L5b C1a-L5a E1b-L4b E1a-L4a G1b-L3b G1a-L3a J1b-L2b J1a-L2a L1b-L1b L1a-L1a 1.00 ROW A NEAR SIDE 2 1 H OPTION 90 (NEAR SIDE - FAR SIDE) NEAR SIDE A1a G 3 ORTHO PIN MAPPING ⌀ 0.46 ± 0.05 PTH ( ⌀ 0.57 DRILL) ( ⌀ 0.88 PAD) 18.50 15.80 12.10 8.40 11.10 NEAR SIDE A1b 7 8 7.40 1.00 3.70 0.00 H 9 14.80 10 11 4.70 12 0.00 0.85 1.85 2.70 A2b-J6b A2a-J6a C2b-J5b C2a-J5a E2b-J4b E2a-J4a G2b-J3b G2a-J3a J2b-J2b J2a-J2a L2b-J1b L2a-J1a A3b-G6b A3a-G6a C3b-G5b C3a-G5a E3b-G4b E3a-G4a G3b-G3b G3a-G3a J3b-G2b J3a-G2a L3b-G1b L3a-G1a A4b-E6b A4a-E6a C4b-E5b C4a-E5a E4b-E4b E4a-E4a G4b-E3b G4a-E3a J4b-E2b J4a-E2a L4b-E1b L4a-E1a A5b-C6b A5a-C6a C5b-C5b C5a-C5a E5b-C4b E5a-C4a G5b-C3b G5a-C3a J5b-C2b J5a-C2a L5b-C1b L5a-C1a A6b-A6b A6a-A6a C6b-A5b C6a-A5a E6b-A4b E6a-A4a G6b-A3b G6a-A3a J6b-A2b J6a-A2a L6b-A1b L6a-A1a G 3.70 4.55 F F 5.55 ORTHO PIN MAPPING 6.40 7.40 OPTION 270 (NEAR SIDE - FAR SIDE) 8.25 A1b-A1a A1a-A1b C1b-A2a C1a-A2b E1b-A3a E1a-A3b G1b-A4a G1a-A4b J1b-A5a J1a-A5b L1b-A6a L1a-A6b 9.25 10.10 11.10 E 11.95 12.95 13.80 14.80 15.65 16.65 17.50 D A2b-C1a A2a-C1b C2b-C2a C2a-C2b E2b-C3a E2a-C3b G2b-C4a G2a-C4b J2b-C5a J2a-C5b L2b-C6a L2a-C6b A3b-E1a A3a-E1b C3b-E2a C3a-E2b E3b-E3a E3a-E3b G3b-E4a G3a-E4b J3b-E5a J3a-E5b L3b-E6a L3a-E6b A4b-G1a A4a-G1b C4b-G2a C4a-G2b E4b-G3a E4a-G3b G4b-G4a G4a-G4b J4b-G5a J4a-G5b L4b-G6a L4a-G6b A6b-L1a A6a-L1b C6b-L2a C6a-L2b E6b-L3a E6a-L3b G6b-L4a G6a-L4b J6b-L5a J6a-L5b L6b-L6a L6a-L6b A5b-J1a A5a-J1b C5b-J2a C5a-J2b E5b-J3a E5a-J3b G5b-J4a G5a-J4b J5b-J5a J5a-J5b L5b-J6a L5a-J6b E D NOTES: ROW A FAR-SIDE 17.65 13.95 16.65 12.95 9.25 10.25 C 6.55 2.85 1.85 5.55 18.50 NEAR SIDE L6b NEAR SIDE NEAR SIDE NEAR SIDE L6a C FAR SIDE FAR SIDE Orthogonal PCB Layout OPTION 90 OPTION 270 SIGNAL PAIRS (SHARED VIAS) B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION NEAR SIDE GROUNDS A DOCUMENT STATUS 12 P1 RELEASE DATE 11 SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) FAR SIDE GROUNDS FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 DIMENSION UNITS 2022/02/18 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:03:40 9 8 7 6 5 EC NO: 671119 DRWN: YOGEEB CHK'D: MMALLIGEVALU APPR: CWANG25 INITIAL REVISION: DRWN: BPISZCZOR APPR: JLAURX THIRD ANGLE PROJECTION 4 2021/06/17 2021/08/20 2022/02/18 I-TRAC BACKPLANE HEADER UNGUIDED ASSEMBLY SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2006/06/06 2006/06/12 DRAWING SERIES C-SIZE 75705 3 SD-75705-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 4 OF 4 1 A