0757145002

12 11 10 14.00 ±0.10 TYP OUTER LIGHT PIPE PORTS H 9 7 8 INNER LIGHT PIPE PORTS 5 6 4 3 2 1 63.25 REF 0.92 REF 12.62 REF H 9.00 ±0.10 TYP G 6.50 REF 12.22 ±0.10 25.83 REF 25.00 ±0.10 25.50 G 9.00 ±0.10 TYP 6.91 ±0.10 3.40 PEGS 1.18 REF F 7.125 TYP 8.00 TYP 3.05 GROUNDS 4.00 TYP 3.67 8.00 TYP 11.00 TYP E SIGNALS TYP GROUNDS TYP 11.50 F ⌖ ⌀ 0.25 Ⓜ A B ⌖ ⌀ 0.25 Ⓜ A B B 14.25 2.07 ±0.25 SIGNALS A 42.10 7.50 51.63 E 1.625 28.50 D C B A NOTES 1. MATERIAL: CAGE: NICKEL SILVER, THICKNESS: 0.25mm CONNECTOR HOUSING: GLASS FILLED HIGH TEMP PLASTIC, 94 V-0 COLOR BLACK OVERMOLDED TERMINALS HOUSING: GLASS FILLED HIGH TEMP PLASTIC, 94 V-0, COLOR: BLACK TERMINALS: TIN BRASS LIGHT PIPES: POLYCARBONITE, 94 V-0, COLOR: CLEAR LIGHT PIPE HOUSING: ZINC 2. FINISH: LIGHT PIPE HOUSING: 150 MICROMETERS NICKEL OVER 150 MICROMETERS COPPER TERMINAL: CONTACT AREA: 0.76 MICROMETERS MINIMUM, HARD GOLD OVER 1.27 MICROMETERS MINIMUM NICKEL. COMPLIANT TAIL - TIN/LEAD OPTION: 0.76 - 1.52 MICROMETERS 90/10 TIN/LEAD OVER 0.76 - 1.52 MICROMETERS NICKEL COMPLIANT TAIL - TIN OPTION: 0.76 - 1.52 MICROMETERS TIN OVER 0.76 - 1.52 MICROMETERS NICKEL 3. REFER TO PS-75310-001 PRODUCT SPEC FOR ALL ELECTRICAL, MECHANICAL, AND ENVIRONMENTAL SPECIFICATIONS. 4. LIGHT PIPE PAD LAYOUT IS FOR 0805 LOW-PORFILE LED PACKAGE, FOR OTHER RECOMMENDED LAYOUTS REFER TO MOLEX'S REPORT TS-75310-001. 5. REFER TO PK-75714-001 FOR ALL PACKAGING SPECIFICATIONS. 6. THE CURVED TAILS THAT GO INTO THE HOLES LOCATED BY THESE DIMENSIONS ARE BEING ELIMINATED. TO ACCOMMODATE THIS CONVERSION, IT IS RECOMMENDED THAT BOARDS DESIGNED TO THIS PRINT REVISION INCLUDE THESE HOLES. 7. PART COMPLIES WITH COSMETIC SPECIFICATION PS-45499-002. SEE SHEET 4 SECTION A-A FOR SURFACE CLASSIFICATIONS. UNDERSIDE OF CAGE COMPLIES WITH CLASS "C". DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/01/08 10 D C PART NUMBER DESCRIPTION 75714-5001 4 PORT LIGHT PIPE 75714-5002 INNER 2 PORTS SCALE mm 3:1 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) 14:15:10 8 COMPLIANT TAIL PLATING TIN TIN B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 5.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 VIEW SEE PG 2 SEE PG 2 7 6 5 EC NO: 648356 DRWN: SKRISHNAMURT CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JLONG APPR: RNELSON THIRD ANGLE PROJECTION 4 2018/10/09 2021/01/08 2021/01/08 STACKED SFP 2X2 MEDIUM HEIGHT ASS'Y, PRESS-FIT TAILS WITH LIGHT PIPES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2004/12/01 2004/12/02 DRAWING SERIES C-SIZE 75714 3 SD-75714-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 1 OF 4 1 A 12 11 10 9 7 8 6 5 4 3 2 1 H H 28.75 REF 14.25 0.92 REF G G 75714-5001 WITH INNER/OUTER LIGHT PIPES F F E E 1.39 TYP 75714-5002 WITH INNER LIGHT PIPES 1.55 TYP D D 3.93 11.17 3.93 C 11.00 TYP 0.40 TYP 12.25 TYP 1.70 TYP 3.80 REF B 7.60 TYP C A ⌖ ⌀ 0.25 Ⓜ A B (4 PLACES) B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 25.25 DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/01/08 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 5.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:15:10 9 8 7 6 5 EC NO: 648356 DRWN: SKRISHNAMURT CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JLONG APPR: RNELSON THIRD ANGLE PROJECTION 4 2018/10/09 2021/01/08 2021/01/08 STACKED SFP 2X2 MEDIUM HEIGHT ASS'Y, PRESS-FIT TAILS WITH LIGHT PIPES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2004/12/01 2004/12/02 DRAWING SERIES C-SIZE 75714 3 SD-75714-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 2 OF 4 1 A 12 11 10 9 7 8 5 6 4 3 2 1 25.25 T20 T18 T16 T14 T12 H T19 T17 T15 T13 T1 T3 T5 T11 T7 INNER LIGHTPIPE OUTLINE TYP B 8.00 TYP 11.00 TYP SEE DETAIL A H 4.00 TYP 5.50 TYP T9 SEE CONNECTOR PIN-OUT A T2 L10 T4 L8 T6 L6 T8 L4 T10 L2 7.50 L9 G L11 L12 L7 L5 L3 L1 L13 L15 L17 L19 L14 L16 L18 G L20 SEE LIGHTPIPE LOCATION DETAIL DETAIL B CONNECTOR PIN-OUT COMPONENT SIDE OF BOARD SCALE 8:1 F 51.63 42.10 E 25.675 7.20 4.00 6 PLACES 8.00 TYP 1.70 REF 3.80 ⌖ ⌀ 0.10 Ⓜ A B ⌀0.46 ±0.05 4.50 ±0.10 TYP D E 6.80 6.40 1.60 TYP CIRCUIT #1 TOP MODULE F 1.75 6 PLACES TRACE KEEP OUT AREA - 6 PLACES 11.00 1.70 REF 3.50 6 PLACES OUTER LIGHTPIPE OUTLINE TYP ⌖ ⌀ 0.10 Ⓜ A B 5.675 TYP SEE NOTE 6 ⌀1.85 ±0.05 EDGE OF BOARD TYP 7.125 TYP 8.575 TYP A 0.98 INNER LIGHTPIPE OUTLINE ⌖ ⌀ 0.10 Ⓜ A B ⌀1.05 ±0.05 7.125 REF TYP 11.075 TYP 14.25 TYP C 0.73 D 0.13 2 PLACES C 28.50 6.52 5.14 0.65 RECOMMENDED PCB LAYOUT - COMPONENT SIDE RECOMMENDED PCB THICKNESS - 2.36 MM (.093 INCH) THE ENTIRE AREA OF THE CONNECTOR FOOTPRINT TO BE CONSIDERED THE KEEP OUT AREA FOR COMPONENTS (OTHER THAN LIGHT PIPE LED'S) THIS AREA IS INDICATED BY THE DASHED LINE 3.59 2.20 2.28 B 3.67 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) OUTER LIGHTPIPE OUTLINE A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 CIRCUIT #1 BOTTOM MODULE RELEASE DATE 11 2021/01/08 10 DETAIL A SCALE 8:1 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 5.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:15:10 9 8 7 6 5 EC NO: 648356 DRWN: SKRISHNAMURT CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JLONG APPR: RNELSON THIRD ANGLE PROJECTION 4 2018/10/09 2021/01/08 2021/01/08 STACKED SFP 2X2 MEDIUM HEIGHT ASS'Y, PRESS-FIT TAILS WITH LIGHT PIPES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2004/12/01 2004/12/02 DRAWING SERIES C-SIZE 75714 3 SD-75714-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 3 OF 4 1 A 12 11 10 9 8 7 5 6 4 3 2 1 SEE NOTE 7 CLASS A H CLASS B H 29.50 ±0.10 3.50 ±0.30 BEZEL A FRONT EDGE OF CONNECTOR BEZEL CUT-OUT G G 25.875 REF 26.00 ±0.10 F F 0.125 ±0.10 BEZEL OPENING BELOW TOP OF PC BOARD A PC BOARD SECTION A-A 3.50 REF 30.65 MINIMUM E 7.00 REF BEZEL CUT-OUT CENTER SPACING DETAIL BEZEL THICKNESS: 0.8 -2.6 E 4.41 3.95 D D 0.70 1.50 THE HATCHED AREA IN THIS VIEW INDICATES ZONES THAT ARE OCCUPIED BY THE PLASTIC HOUSING THAT SEATS AGAINST THE PCB AND BY THE VERTICAL METAL CAGE WALL THAT STOPS JUST SHORT OF THE PCB 1.25 0.25 1.90 0.35 C C 2.56 3.57 4.90 7.85 7.11 10.06 11.43 13.13 B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) 0.62 REF 0.62 A 2.00 DETAIL - LIGHT PIPE LOCATION AND OTHER ZONES SCALE 8:1 DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/01/08 10 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 5.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:15:10 9 ANGULAR TOL 8 7 6 5 EC NO: 648356 DRWN: SKRISHNAMURT CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JLONG APPR: RNELSON THIRD ANGLE PROJECTION 4 2018/10/09 2021/01/08 2021/01/08 STACKED SFP 2X2 MEDIUM HEIGHT ASS'Y, PRESS-FIT TAILS WITH LIGHT PIPES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2004/12/01 2004/12/02 DRAWING SERIES C-SIZE 75714 3 SD-75714-001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 E1 SHEET NUMBER 4 OF 4 1 A