0764505608

19 18 17 # OF COLUMNS MATERIAL NUMBER 16 # OF DIFF PAIR 15 DIM "A" MAX 14 13 12 11 10 9 7 8 L 10 20 26.60 17.10 76450-*60* 16 32 38.00 28.50 76450- ** 0 * PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.39 PTH) 8 = 5.50 (0.39 PTH) MODULE & TAIL PLATING TYPE 5 = RIGHT GUIDED LEAD-FREE 9 = RIGHT GUIDED LEAD-FREE W/ ENDWALL K 4 3 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µin SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. FOR FURTHER INFORMATION SEE PRODUCT SPECIFICATION PS-76060-999.. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT TO BE PACKAGED PER PACKAGING SPECIFICATION PK-70873-077. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76460-002 FOR MATING DAUGHTERCARDS. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. WHEN USING MOLEX SUPPLIED #2-32 SCREW 73726-0005 (7.62 +0.38/-0.76 mm THREADABLE SCREW LENGTH), THE BOARD THICKNESS RANGE IS 1.60 TO 3.85 mm. 10. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. DIM "B" 76450-*10* 5 6 # OF COLUMNS 1 = 10 COL 6 = 16 COL J L K J 9.7 1.00 MIN BOARD THICKNESS 9.2 1.2 TAIL LENGTH "A" H H 7.60 3.80 6.75 G G SEE NOTE 10 ENDWALL OPTION OPEN ENDED OPTION 18.4 24.65 6.64 "B" 8.66 0.84 F ⌖ ⌀ 0.10 1.50 ADD FOR ENDWALL P �33.3� �9.31� F 1.90 ⌀3.80 ±0.05 5.10 UNPLATED HOLE KEEP OUT ZONE E E 3.0 ROW F ROW E ROW D ROW C ROW B ROW A 1.50 (ADD FOR ENDWALL) 12.7 5.00 6.75 8.70 D D GROUND HOLES REF SIGNAL HOLES REF PIN A1 RAM HOLE PATTERN (CONNECTOR SIDE) C 1.70 ⌖ ⌀ 0.10 MAX ⌀ PTH ±0.05 SEE CHART (6 HOLES PER COLUMN) SEE NOTE 3 1.35 5X C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2022/05/13 16 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:34 15 14 13 12 11 10 9 8 7 6 B EC NO: 705090 DRWN: PSHANKARACHA CHK'D: VINODM3 APPR: LZENG INITIAL REVISION: DRWN: MCARRANZA APPR: JLAURX THIRD ANGLE PROJECTION 5 2019/03/13 2022/03/08 2022/05/13 IMPACT 100 OHM 2 PAIR RAM RIGHT GUIDED SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/02/21 2009/04/17 DRAWING SERIES D-SIZE 76450 4 SD-76450-004 MATERIAL NUMBER SEE TABLE 3 PSD 001 C8 SHEET NUMBER CUSTOMER GENERAL MARKET 2 1 OF 2 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L L COPLANAR APPLICATION K DAUGHTERCARD ASSEMBLY 76460 K RAM ASSEMBLY 76450 J J TOP OF BOARD TOP OF BOARD 18.00 H H 35.40 G G ROW F ROW A PIN A10 ROW A ROW F PIN A10 F TOP OF BOARD (RAM) TOP OF BOARD (DC) F 0.35 PIN A1 E E PIN A1 COPLANAR MATED SIGNAL PATHS DC PIN A10 --------------------------------------- RAM PIN A10 I I I I I I DC PIN A1 --------------------------------------- RAM PIN A1 D D C C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2022/05/13 16 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:34 15 14 13 12 11 10 9 8 7 6 B EC NO: 705090 DRWN: PSHANKARACHA CHK'D: VINODM3 APPR: LZENG INITIAL REVISION: DRWN: MCARRANZA APPR: JLAURX THIRD ANGLE PROJECTION 5 2019/03/13 2022/03/08 2022/05/13 IMPACT 100 OHM 2 PAIR RAM RIGHT GUIDED SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/02/21 2009/04/17 DRAWING SERIES D-SIZE 76450 4 SD-76450-004 MATERIAL NUMBER SEE TABLE 3 PSD 001 C8 SHEET NUMBER CUSTOMER GENERAL MARKET 2 2 OF 2 1 A