0764603020

12 11 10 9 7 8 5 6 4 3 2 1 1.2 (TAIL LENGTH) 9.2 H 7.60 SEE NOTE 12 3.80 H 1.60 MIN BOARD THICKNESS SEE NOTE 10 SEE NOTE 9 8.70 6.75 SEE NOTE 9 G G 11.36 F PIN A1 F A �2.1� BP ROW A BACKPLANE (REF) 1.90 10.9 E B 8.44 SIGNAL HOLES REF 4.40 E 1.06 KEEP-OUT ZONE GROUND HOLE REF 8.70 D 6.75 5.00 B A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/08/08 10 1.35 5X 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS ⌖ ⌀0.10 ⌀3.80 ±0.04 7 ⌀PTH BP PIN A1 C (SEE CHART) (6 HOLES PER COLUMN) SEE NOTE 3. BACKPLANE (REF) DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) 22:00:48 8 ⌖ ⌀0.10 UNPLATED HOLE ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 D 1.70 MAX NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 14.00 TERMINALS - HIGH PERFORMANCE COPPER ALLOY (FULLY MATED) 2. FINISH: 30µIN MIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-592. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76455-002 FOR THE MATING HEADERS AND SD-76460-004 FOR MATING RAM. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. PART NUMBER 76460-1020 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 10. MINIMUM BOARD THICKNESS IS 1.60 mm FOR GUIDE MODULE SCREW PEG HOLD DOWN FUNCTIONALITY. 11. WHEN USING MOLEX SUPPLIED #2-32 SCREW 73726-4000 (4.31mm ±0.38 THREADABLE SCREW LENGTH), THE MAXIMUM BOARD THICKNESS IS 1.8 mm TO 2.4 mm. 12. THIS NOTCH IS A DIE NOTCH. IT IS SHOWN TO IDENTIFY IT'S PRESENCE, NOT IT'S POSITION. (THIS WILL VARY WITH PART LENGTH), IT SERVES NO PURPOSE IN THE FINISHED ASSEMBLY. 13. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. C ROW F ROW E ROW D ROW C ROW B ROW A 6 5 EC NO: 622030 DRWN: SKRISHNAMU01 CHK'D: PRAMASWAMY APPR: SHONG INITIAL REVISION: DRWN: TELO APPR: JLAURX THIRD ANGLE PROJECTION 4 2019/07/30 2019/08/07 2019/08/08 IMPACT 100 OHM DC 2 PAIR SIGNAL MODULE GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/09/29 2008/09/30 DRAWING SERIES C-SIZE 76460 3 SD-76460-002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 E3 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 10 9 8 7 6 5 4 3 2 1 H H G MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" PTH⌀ 76460-*010 10 20 26.60 17.10 76460-*016 16 32 38.00 28.50 0.46 ±0.05 76460-*020 10 20 26.60 17.10 76460-*026 16 32 38.00 28.50 76460- 0 * ** 0.39 ±0.05 MODULE & TAIL PLATING TYPE 3 = LEFT GUIDED LEAD-FREE G # OF COLUMNS 10 = 10 COL 0.46 PTH 16 = 16 COL 0.46 PTH 20 = 10 COL 0.39 PTH 26 = 16 COL 0.39 PTH F F E E D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/08/08 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 22:00:48 9 8 7 6 5 EC NO: 622030 DRWN: SKRISHNAMU01 CHK'D: PRAMASWAMY APPR: SHONG INITIAL REVISION: DRWN: TELO APPR: JLAURX THIRD ANGLE PROJECTION 4 2019/07/30 2019/08/07 2019/08/08 IMPACT 100 OHM DC 2 PAIR SIGNAL MODULE GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/09/29 2008/09/30 DRAWING SERIES C-SIZE 76460 3 SD-76460-002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 E3 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A