0764605010

12 11 10 9 8 7 5 6 4 3 2 1 1.2 (TAIL LENGTH) 9.2 3.80 H 7.60 1.60 MIN BOARD THICKNESS SEE NOTE 10 SEE NOTE 12 SEE NOTE 9 8.70 6.75 H SEE NOTE 13 G G 11.36 PIN A1 F F BACKPLANE (REF) 10.9 BP ROW A A �2.1� B 8.66 0.84 E 5.10 SIGNAL HOLES REF E 1.90 KEEP-OUT ZONE GROUND HOLE REF ROW F ROW E ROW D ROW C ROW B ROW A D 5.00 PIN A1 C B A NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN MIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-592. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLES SALES DRAWING SD-76455-003 FOR THE MATING HEADERS AND SD-76450-002 FOR MATING RAM. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. PART NUMBER 76460-5020 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 10.MINIMUM BOARD THICKNESS IS 1.60 mm FOR GUIDE MODULE SCREW PEG HOLD DOWN FUNCTIONALITY. 11.WHEN USING MOLEX SUPPLIED #2-32 SCREW 73726-4000 (4.31mm ±0.38 THREADABLE SCREW LENGTH), THE MAXIMUM BOARD THICKNESS IS 1.8 mm TO 2.4 mm. 12. THIS NOTCH IS A DIE NOTCH. IT IS SHOWN TO IDENTIFY IT'S PRESENCE, NOT IT'S POSITION. (THIS WILL VARY WITH PART LENGTH), IT SERVES NO PURPOSE IN THE FINISHED ASSEMBLY. 13. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/08/08 10 ⌖ ⌀0.10 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS ⌀PTH (SEE CHART) (6 HOLES PER COLUMN) SEE NOTE 3. 7 D 1.35 5X 14.00 (FULLY MATED) ⌀3.80 C UNPLATED HOLE BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) 22:00:48 8 ⌖ ⌀0.10 8.70 BACKPLANE (REF) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 1.70 MAX 6.75 6 5 EC NO: 622030 DRWN: SKRISHNAMU01 CHK'D: PRAMASWAMY APPR: SHONG INITIAL REVISION: DRWN: TELO APPR: JLAURX THIRD ANGLE PROJECTION 4 IMPACT 100 OHM DC 2019/07/31 2 PAIR SIGNAL MODULE GUIDE RIGHT SALES DWG 2019/08/07 2019/08/08 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/09/29 2008/09/30 DRAWING SERIES C-SIZE 76460 3 SD-76460-004 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 D3 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 10 9 7 8 6 5 4 3 2 1 H H MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" PTH⌀ 76460-*010 10 20 26.60 17.10 76460-*016 16 32 38.00 28.50 0.46 ±0.05 76460*020 10 20 26.60 17.10 76460-*026 16 32 38.00 28.50 0.39 ±0.05 76460- 0 * ** G MODULE & TAIL PLATING TYPE 5 = RIGHT GUIDED LEAD-FREE G # OF COLUMNS 10 = 10 COL 0.46 PTH 16 = 16 COL 0.46 PTH 20 = 10 COL 0.39 PTH 26 = 16 COL 0.39 PTH F F E E D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/08/08 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 22:00:48 9 8 7 6 5 EC NO: 622030 DRWN: SKRISHNAMU01 CHK'D: PRAMASWAMY APPR: SHONG INITIAL REVISION: DRWN: TELO APPR: JLAURX THIRD ANGLE PROJECTION 4 IMPACT 100 OHM DC 2019/07/31 2 PAIR SIGNAL MODULE GUIDE RIGHT SALES DWG 2019/08/07 2019/08/08 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2008/09/29 2008/09/30 DRAWING SERIES C-SIZE 76460 3 SD-76460-004 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 D3 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A