0765601104

19 18 17 # OF COLUMNS MATERIAL NUMBER 16 # OF DIFF PAIR 15 DIM "A" MAX DIM "B" 14 13 12 11 PTH⌀ 10 76560- L K 76560-11** 10 60 19.00 17.10 0.46±0.05 76560-17** 14 84 26.60 24.70 0.46±0.05 76560-16** 16 96 30.40 28.50 0.46±0.05 76560-11** 10 60 19.00 17.10 0.39±0.05 76560-17** 14 84 26.60 24.70 0.39±0.05 76560-16** 16 96 30.40 28.50 0.39±0.05 9 7 8 6 PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.39 PTH) 8 = 5.50 (0.39 PTH) # OF COLUMNS 1 = 10 COLUMNS 6 = 16 COLUMNS 7 = 14 COLUMNS END WALL OPTIONS 0 = OPEN 1 = LEFT END WALL 2 = DUAL END WALL 3 = RIGHT END WALL 25.90 J 1.00 MIN PCB THICKNESS 24.8 3 2 1 L K J "B" 1.2 TAIL LENGTH "A" 4 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-777. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76150-001 FOR THE MATING RECEPTACLES. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. OPEN WALL VERSION SHOWN FOR CLARITY. SEE PCB LAYOUT FOR OVERALL LENTH ADDITION ON THE ASSEMBLIES WITH ENDWALLS. 10. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. 11. THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE CONNECTOR INSERTION AND REPAIR ON THE PCB.THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. **** MODULE TYPE 1 = UNGUIDED, LEAD-FREE 5 0.84 1.06 3.80 1.30 (ADD FOR ENDWALL) H H 1.50 (ADD FOR ENDWALL) 1.90 GROUND HOLE REF SIGNAL HOLE REF 25.90 G KEEP OUT ZONE SEE NOTE 11 G 22.95 ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A SEE NOTE 10 �41.8� F 6.64 "P" E 1.50 ADD FOR ENDWALL 2.9 1.30 ADD FOR ENDWALL 28.9 D F 25.90 22.95 E D ⌖ ⌀0.10 PIN A1 1.70 MAX ⌀ PTH (SEE CHART) (18 HOLES PER COLUMN) SEE NOTE 3 C 1.35 17X RAM HOLE PATTERN C (CONNECTOR SIDE) SYMBOLS = 0 = 0 B = 0 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/11/06 16 21:57:25 C 15 14 13 12 11 10 9 8 mm 4:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 7 CURRENT REV DESC: CORRECT PIN CALLOUTS GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS SCALE ANGULAR TOL = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 B EC NO: 607222 DRWN: DVARVARA CHK'D: DMORGAN APPR: DMORGAN INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 5 2018/11/06 2018/11/06 2018/11/06 IMPACT 6 PAIR RAM MARRIED - UNGUIDED SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2014/11/24 2016/01/10 DRAWING SERIES D-SIZE 76560 4 SD-76560-9001 MATERIAL NUMBER SEE TABLE 3 PSD 001 A2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 1 OF 2 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 L L COPLANER APPLICATION DC ASSEMBLY: 76150 RAM ASSEMBLY: 76560 K K J J TOP OF BOARD TOP OF BOARD H H 18.00 69.80 G G ROW A ROW T ROW A ROW T PIN A1 PIN A1 F F 0.35 TOP OF BOARD (PCB RAM) TOP OF BOARD (PCB DC) E E D D PIN A10 PIN A10 COPLANER MATED SIGNAL PATHS C RAM PIN A10 C DC PIN A10 SYMBOLS RAM PIN A1 DC PIN A1 = 0 = 0 B = 0 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/11/06 16 21:57:25 C 15 14 13 12 11 10 9 8 mm 4:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 7 CURRENT REV DESC: CORRECT PIN CALLOUTS GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS SCALE ANGULAR TOL = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 B EC NO: 607222 DRWN: DVARVARA CHK'D: DMORGAN APPR: DMORGAN INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 5 2018/11/06 2018/11/06 2018/11/06 IMPACT 6 PAIR RAM MARRIED - UNGUIDED SALES DRAWING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2014/11/24 2016/01/10 DRAWING SERIES D-SIZE 76560 4 SD-76560-9001 MATERIAL NUMBER SEE TABLE 3 PSD 001 A2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 2 OF 2 1 A