0765605608

20 M 19 18 17 16 15 14 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" PTH⌀ 76560-*1** 10 60 26.60 17.10 0.46±0.05 76560-*7** 14 84 34.20 24.70 0.46±0.05 76560-*6** 16 96 38.00 28.50 0.46±0.05 76560-*1** 10 60 26.60 17.10 0.39±0.05 76560-*7** 14 84 34.20 24.70 0.39±0.05 76560-*6** 16 96 38.00 28.50 0.39±0.05 L 13 12 10 11 9 7 8 PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.39 PTH) 8 = 5.50 (0.39 PTH) # OF COLUMNS 1 = 10 COLUMNS 6 = 16 COLUMNS 7 = 14 COLUMNS K 25.90 "A" 1.2 TAIL LENGTH 24.8 1.00 MIN PCB THICKNESS 3.80 J 4 3 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-777. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76150-002 FOR THE MATING RECEPTACLES. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. OPEN WALL VERSION SHOWN FOR CLARITY, SEE PCB LAYOUT FOR OVERALL LENGTH ADDITION ON THE ASSEMBLIES WITH ENDWALLS. 10. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. 11. THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE CONNECTOR INSERTION AND REPAIR ON THE PCB.THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. 76560-**** MODULE TYPE 5 = GUIDED, LEAD-FREE 9 = GUIDED, LEAD-FREE W/ ENDWALL 5 6 KEY ORIENTATION 0 = NO KEY 1= A 2= B 3= C 4= D 5= E 6= F 7= G 8= H B M L K 8.37 J 1.00 5.10 1.50 (ADD FOR ENDWALL) GROUND HOLE REF SIGNAL HOLE REF H 25.90 SEE NOTE 10 �41.8� G 6.64 59.0±0.3 "P" F H ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A 22.95 Cutaway1 E KEEP OUT ZONE SEE NOTE 11 1.50 ADD FOR ENDWALL ⌖ ⌀0.10 ⌀ 2.45 ±0.04 UNPLATED HOLE X2 G 25.90 22.95 14.05 F 16.03 E PIN A1 ⌖ ⌀0.10 2.9 1.35 17X ⌀ PTH (SEE CHART) RAM HOLE PATTERN (CONNECTOR SIDE) (18 HOLES D PER COLUMN) 28.9 1.70 MAX D SEE NOTE 3 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS C CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2022/05/13 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:39 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 IMPACT 6 PAIR RAM MARRIED GUIDE RIGHT SALES DRAWING EC NO: 705090 DRWN: YOGEEB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 6 2021/12/10 2022/02/10 2022/05/13 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/06/25 2016/01/10 DRAWING SERIES D-SIZE 76560 5 SD-76560-9004 MATERIAL NUMBER GENERAL MARKET 3 A3 SHEET NUMBER CUSTOMER SEE TABLE 4 PSD 001 2 1 OF 2 1 A 20 19 18 17 16 15 14 13 12 10 11 9 7 8 5 6 4 3 2 1 M M COPLANAR APPLICATION RAM ASSEMBLY: 76560 L DC ASSEMBLY: 76150 L K K TOP OF BOARD J TOP OF BOARD J 18.00 69.80 H ROW A ROW T H ROW A ROW T PIN A1 PIN A1 G G TOP OF BOARD (PCB RAM) TOP OF BOARD (PCB DC) 0.35 F F E E PIN A10 PIN A10 COPLANAR MATED SIGNAL PATHS D D RAM PIN A1 ---------- DC PIN A1 | | | | RAM PIN A10 --------- RAM PIN A10 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS C CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2022/05/13 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:39 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 IMPACT 6 PAIR RAM MARRIED GUIDE RIGHT SALES DRAWING EC NO: 705090 DRWN: YOGEEB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 6 2021/12/10 2022/02/10 2022/05/13 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/06/25 2016/01/10 DRAWING SERIES D-SIZE 76560 5 SD-76560-9004 MATERIAL NUMBER GENERAL MARKET 3 A3 SHEET NUMBER CUSTOMER SEE TABLE 4 PSD 001 2 2 OF 2 1 A