0765607107

20 M 19 18 17 16 15 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" PTH⌀ 76560-*1** 10 60 26.60 17.10 0.46±0.05 76560-*7** 14 84 34.20 24.70 0.46±0.05 76560-*6** 16 96 38.00 28.50 0.46±0.05 76560-*1** 10 60 26.60 17.10 0.39±0.05 76560-*7** 14 84 34.20 24.70 0.39±0.05 76560-*6** 16 96 38.00 28.50 0.39±0.05 L 14 13 12 10 11 MODULE TYPE 3 = GUIDED, LEAD-FREE 7 = GUIDED, LEAD-FREE W/ENDWALL # OF COLUMNS 1 = 10 COLUMNS 6 = 16 COLUMNS 7 = 14 COLUMNS 25.90 1.2 TAIL LENGTH "A" 24.8 1.00 MIN PCB THICKNESS 3.80 7 8 76560-**** K J 9 5 6 4 3 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-777. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76150-004 FOR THE MATING RECEPTACLES. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. WHEN USING A MOLEX SUPPLIED #2-32 SCREW 73726-0000 (9.50mm +/- 0.38 THREADABLE SCREW LENGTH) THE MAXIMUM BOARD THICKNESS IS 4.4MM. 10. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. 11. THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE CONNECTOR INSERTION AND REPAIR ON THE PCB. THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.39 PTH) 8 = 5.50 (0.39 PTH) KEY ORIENTATION 0 = NO KEY 1=A 2=B 3=C 4=D 5=E 6=F 7=G 8=H M L K J B 8.59 1.90 0.77 4.40 1.30 (ADD FOR ENDWALL) GROUND HOLE REF H 25.90 SEE NOTE 10 22.95 KEEP OUT ZONE SEE NOTE 11 SIGNAL HOLE REF �41.9� ⌖ ⌀0.10 ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A ⌀ 2.45 ±0.04 G UNPLATED HOLE X2 6.64 59.0 ±0.30 "P" F 25.90 22.95 14.05 2.9 1.30 ADD FOR ENDWALL E H 16.03 ⌖ ⌀0.10 D 28.9 1.70 MAX (SEE CHART) (18 HOLES PER COLUMN) SEE NOTE 3 C SCALE mm NTS E 1.35 17X RAM HOLE PATTERN (CONNECTOR SIDE) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS F D PIN A1 ⌀ PTH G C CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2022/05/13 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:38 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 IMPACT 6 PAIR RAM MARRIED GUIDE LEFT SALES DRAWING EC NO: 705090 DRWN: YOGEEB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 6 2021/12/07 2022/01/31 2022/05/13 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/06/25 2016/01/10 DRAWING SERIES D-SIZE 76560 5 SD-76560-9002 MATERIAL NUMBER GENERAL MARKET 3 A3 SHEET NUMBER CUSTOMER SEE TABLE 4 PSD 001 2 1 OF 2 1 A 20 19 18 17 16 15 14 13 12 10 11 9 7 8 5 6 4 3 2 1 M M COPLANAR APPLICATION L RAM ASSEMBLY: 76560 L DC ASSEMBLY: 76150 K K TOP OF BOARD J J TOP OF BOARD 18.00 H H 69.80 ROW A ROW T ROW A ROW T PIN A1 PIN A1 G G TOP OF BOARD (PCB RAM) TOP OF BOARD (PCB DC) 0.35 F F E E PIN A10 PIN A10 D D COPLANAR MATED SIGNAL PATHS RAM PIN A1 ---------- DC PIN A1 C | | | | RAM PIN A10 --------- DC PIN A10 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS C CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2022/05/13 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:38 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 IMPACT 6 PAIR RAM MARRIED GUIDE LEFT SALES DRAWING EC NO: 705090 DRWN: YOGEEB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: JGONZALEZ01 APPR: TELO THIRD ANGLE PROJECTION 6 2021/12/07 2022/01/31 2022/05/13 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/06/25 2016/01/10 DRAWING SERIES D-SIZE 76560 5 SD-76560-9002 MATERIAL NUMBER GENERAL MARKET 3 A3 SHEET NUMBER CUSTOMER SEE TABLE 4 PSD 001 2 2 OF 2 1 A