0768559608

12 11 10 9 7 8 5 6 4 0.80 4.925 PIN A1 ⌀ 3.56 ±0.08 UNPLATED SCREW HOLE 2.30 1.15 3X 1.90 2.15 1 ⌖ ⌀0.15 1.15 H B 2 8.65 C 1.40 (ADD FOR ENDWALL) A 3 H KEEP-OUT ZONE SEE NOTE 11 3X 2.30 Z ROW A ROW B ROW C ROW D ROW E ROW F ROW G ROW H ROW J 5.20 G 16.95 MAX 1.35 8X 16.7 10.40 2X 4.05 10.80 16.95 MAX F 0.25 Z F ⌖ ⌀0.10 SEE CHART (9 HOLES) PER COLUMN) 0.25 4.05 G DIFFERENTIAL PAIR 4.05 GROUND HOLE BACKPLANE HOLE PATTERN (CONNECTOR SIDE) E E 24.6 (PIN LENGTH) P ±0.20 NOTCH DESIGNATES ROW A 11.95 D D 1.4 2.64 FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 18.10.2017 B 2017/10/17 2017/10/17 2017/10/18 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES mm 4:1 = 0 (UNLESS SPECIFIED) C 06:14:22 10 9 8 7 6 = 0 = 0 = 0 DATE 0 = 0 = 0 = 0 E3 2013/04/01 ARIZVI01 ± 4 PLACES = 5 DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS C (ENDWALL VERSION SHOWN) MIGRATED TO NX A SECTION Z-Z 123283 ABN ABN PRAMASWAMY B 3.00 MINIMUM BOARD EC NO: DRWN: CHK'D: APPR: C NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µ MIN GOLD IN CONTACT AREA. SELECTIVE TIN OR TIN-LEAD ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 5. PRODUCT IS PACKAGED PER PK-70873-763. 6. SEE SHEETS 2 AND 3 FOR PART NUMBERS AND ORTHOGONAL PIN MAPPING. 7. REFER TO MOLEX SALES DRAWING SD-76860-004 FOR THE MATING RECEPTACLES. 8. THE KEEP-OUT ZONE FOR THE PART LENGTH INCLUDES AN ADDITIONAL 1.0mm TO ACCOMMODATE FOR SPACE REQUIRED BY THE DAUGHTERCARD ASSEMBLY. 9. REFER TO MOLEX ROUTING GUIDE AS-76850-990 FOR ADDITIONAL PCB LAYOUT AND ROUTING RECOMMENDATIONS. 10. CONNECTORS ARE SUPPLIED WITH A 2-56 UNC-2A SCREW. 11."THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE CONNECTOR INSERTION AND REPAIR ON THE PC BOARD. THIS DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR." DATE CHK'D BY 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 DATE PRODUCT CUSTOMER DRAWING 2015/03/24 TELO DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 2017/10/13 PRAMASWAMY APPR BY IMPACT 3 PAIR HEADER ORTHOGONAL ASSEMBLY GUIDE RIGHT SALES DWG THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 76855 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-76855-003 3 CUSTOMER 2 PSD 1 OF 3 001 1 A 12 11 10 9 8 7 5 4 3 2 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR MODULE TYPE DIM A DIM B DIM C 76855-*60* 76855-*60* 76855-*80* 76855-*80* 6 6 8 8 18 18 24 24 NO ENDWALL WITH ENDWALL NO ENDWALL WITH ENDWALL 18.9 20.3 22.9 24.3 10.00 10.00 14.05 14.05 10.40 10.40 14.45 14.45 6 ORTHO OPTION 270 H NEARSIDE PIN A1 MAPS TO FARSIDE PIN A1 1 H G G F F 76855- * * 0 * PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.39 PTH) 8 = 5.50 (0.39 PTH) MODULE & TAIL PLATING TYPE 4 = GUIDE RIGHT NO ENDWALL, TIN/LEAD 5 = GUIDE RIGHT NO ENDWALL, TIN 8 = GUIDE RIGHT ENDWALL, TIN/LEAD 9 = GUIDE RIGHT ENDWALL, TIN E E # OF COLUMNS 6 = 6 COLUMNS 8 = 8 COLUMNS D D C C B ORTHO OPTION 90 NEARSIDE PIN A1 MAPS TO FARSIDE PIN J6 (FOR SQUARE PATTERN) FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 11 18.10.2017 C 06:14:22 10 9 8 7 6 0 = 0 = 0 = 0 = 0 = 0 E3 5 DATE 2013/04/01 ARIZVI01 ± 4 PLACES 123283 ABN ABN PRAMASWAMY = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE DATE 0 EC NO: DRWN: CHK'D: APPR: P1 = MIGRATED TO NX 2017/10/17 2017/10/17 2017/10/18 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES mm 4:1 = 0 (UNLESS SPECIFIED) A RELEASE STATUS B OPEN END WALL DATE CHK'D BY 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 DATE PRODUCT CUSTOMER DRAWING 2015/03/24 TELO DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 2017/10/13 PRAMASWAMY APPR BY IMPACT 3 PAIR HEADER ORTHOGONAL ASSEMBLY GUIDE RIGHT SALES DWG THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 76855 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-76855-003 3 CUSTOMER 2 PSD 2 OF 3 001 1 A 12 11 10 ROW A H 9 8 7 5 6 4 3 2 1 H (FARSIDE OPTION 270) SEE DETAIL X ORTHO PIN MAPPING OPTION 270 (NEARSIDE - FARSIDE) NEARSIDE A2 A1 G ROW A B2 B1 C1 ROW B C2 ROW C ROW D A1-A1 A2-B1 A3-D1 A4-E1 A5-G1 A6-H1 B1-A2 B2-C1 B3-D2 B4-F1 B5-G2 B6-J1 C1-B2 C2-C2 C3-E2 C4-F2 C5-H2 C6-J2 D1-A3 D2-B3 D3-D3 D4-E3 D5-G3 D6-H3 E1-A4 E2-C3 E3-D4 E4-F3 E5-G4 E6-J3 F1-B4 F2-C4 F3-E4 F4-F4 F5-H4 F6-J4 G1-A5 G2-B5 G3-D5 G4-E5 G5-G5 G6-H5 H1-A6 H2-C5 H3-D6 H4-F5 H5-G6 H6-J5 J1-B6 J2-C6 J3-E6 J4-F6 J5-H6 J6-J6 G ROW E ROW F F G6 G5 H5 ROW G H6 J5 F ROW H ROW J J6 E ROW A E ORTHO PIN MAPPING (FARSIDE OPTION 90) OPTION 90 (NEARSIDE - FARSIDE) MIDPLANE PCB LAYOUT D C A1-J6 A2-H6 A3-F6 A4-E6 A5-C6 A6-B6 B1-J5 B2-G6 B3-F5 B4-D6 B5-C5 B6-A6 C1-H5 C2-G5 C3-E5 C4-D5 C5-B5 C6-A5 D1-J4 D2-H4 D3-F4 D4-E4 D5-C4 D6-B4 E1-J3 E2-G4 E3-F3 E4-D4 E5-C3 E6-A4 F1-H3 F2-G3 F3-E3 F4-D3 F5-B3 F6-A3 G1-J2 G2-H2 G3-F2 G4-E2 G5-C2 G6-B2 H1-J1 H2-G2 H3-F1 H4-D2 H5-C1 H6-A2 J1-H1 J2-G1 J3-E1 J4-D1 J5-B1 J6-A1 D C SIGNAL PAIR GROUND VIA NOTE: PINOUTS SHOWN IN BALLOONS ARE GROUNDS. PINOUTS SHOWN ARE FOR SQUARE (6 COLUMN) PATTERN ONLY. B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 18.10.2017 C 06:14:22 10 9 8 7 6 0 = 0 = 0 = 0 = 0 = 0 E3 5 DATE 2013/04/01 ARIZVI01 ± 4 PLACES REV RELEASE STATUS = DRWN BY ANGULAR TOL ± 0.5 ° 123283 ABN ABN PRAMASWAMY A 0 EC NO: DRWN: CHK'D: APPR: DETAIL X SCALE 16:1 = MIGRATED TO NX 2017/10/17 2017/10/17 2017/10/18 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES mm 1:1 = 0 (UNLESS SPECIFIED) GROUND VIA SIGNAL PAIR B DATE CHK'D BY 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 DATE PRODUCT CUSTOMER DRAWING 2015/03/24 TELO DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 2017/10/13 PRAMASWAMY APPR BY IMPACT 3 PAIR HEADER ORTHOGONAL ASSEMBLY GUIDE RIGHT SALES DWG THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 76855 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-76855-003 3 CUSTOMER 2 PSD 3 OF 3 001 1 A