0768603036

12 10 11 9 7 8 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" PTH⌀ 76860-3006 6 18 20.25 10.00 0.46±0.05 76860-3036 6 18 20.25 10.00 0.39±0.05 76860-3008 8 24 24.30 14.05 0.46±0.05 76860-3038 8 24 24.30 14.05 0.39±0.05 H 5 6 4 3 2 1 76860 -*0** H MODULE & TAIL PLATING TYPE 3 = LEFT GUIDED, LEAD-FREE 06 36 08 38 1.2 (TAIL LENGTH) # OF COLUMNS = 6 COL 0.46 PTH = 6 COL 0.39 PTH = 8 COL 0.46 PTH = 8 COL 0.39 PTH 13.3 1.60 MIN BOARD THICKNESS 4.05 12.7 G G 10.80 F �24.1� 12.75 B 9.05 SEE NOTE 10 1.20 4.775 2X SIGNAL HOLES REF F 1.90 GROUND HOLE REF 2.15 ⌖ ⌀0.10 11.36 KEEP-OUT ZONE ⌀3.80 ± 0.04 UNPLATED HOLE E E ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A A 12.75 BACKPLANE (REF) �2.1� 10.80 5.91 7.86 0.20 D BP ROW A (SIGNAL) 1.35 8X 1.70 MAX 14.00 (FULLY MATED) PIN A1 ⌖ ⌀0.10 ⌖ ⌀0.10 4.05 ⌀ PTH ⌀ 2.45 ±0.04 0.15 UNPLATED HOLE OFFSET BETWEEN DC AND BP SIGNAL COLUMN 1 15.0 C B A NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN MIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-591. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-76855-002 FOR THE MATING HEADERS. 8. WHEN USING MOLEX SUPPLIED #2-32 SCREW 73726-4000 (4.31mm ±0.38 THREADABLE SCREW LENGTH), THE MAXIMUM BOARD THICKNESS IS 2.4mm. 9. REFER TO MOLEX ROUTING GUIDE AS-76850-990 FOR ADDITIONAL PCB LAYOUT AND ROUTING RECOMMENDATIONS. 10. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/05/13 10 7 C BP PIN COL 1 (SIGNAL) DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) 03:06:40 8 (SEE CHART) (9 HOLES PER COLUMN) SEE NOTE 3. BACKPLANE (REF) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.15 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 D 6 5 EC NO: 705090 DRWN: YOGEEB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: JLAURX APPR: JBINGHAM THIRD ANGLE PROJECTION 4 2021/12/03 2022/01/31 2022/05/13 IMPACT DAUGHTERCARD 3 PAIR ORTHOGONAL GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/01/11 2010/01/14 DRAWING SERIES C-SIZE 76860 3 SD-76860-002 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 B4 SHEET NUMBER 1 OF 1 1 A