0781273320

9 7 8 5 6 4 3 2 1 NOTES 1. 梱包数量： 2000個／リール NUMBER OF CONNECTORS : 2000 PCS/REEL 2. リードテープ長さ LEAD TAPE LENGTH トップテープ未接着部 100MIN. 25 ± 10 引き出し方向 PULL OUT DIRECTION E ELV&RoHS COMPLINT TOP TAPE NON-BONDED PART トップテープ接着部 E TOP TAPE BONDED PART (空エンボス) (EMPTY) ( ⌀ 380) PULL OUT DIRECTION COMPONENT SUPPLIER TOP TAPE LEADER PART 400MIN. 末端部 (空部) TAIL PART (EMPTY) 510MIN. 　 3. トップテープの剥離強度については、IEC60286-3に準拠。 TOP TAPE PEEL FORCE IS DEFINED BY IEC60286-3. 4. 製品詳細寸法については、図面781271002をご参照ください。 REFER TO THE 781271002 ABOUT DIMENSIONS IN DETAIL. 5. 材料 　　キャリアテープ：ポリスチレン(PS) 　　トップテープ　：PET,OTHER 　　リール　　　　：ポリスチレン(PS) � リサイクル材を含む � MATERIAL CARRIER TAPE : POLYSTYRENE(PS) TOP TAPE : PET,OTHER REEL : POLYSTYRENE(PS) (RECYCLE MATERIAL CONTAINED) 6. 環境負荷物質の管理のため「化学物質ガイドライン」の内容を満足すること。 "CHEMICAL SUBSTANCES GUIDELINE" SHALL BE APPLIED FOR MANAGEMENT OF ENVIRONMENTAL HAZARDOUS MATERIALS. D REEL A±1 B±1 "E" 部品挿入部 トップテープ リーダー部 引き出し方向 C (⌀10) D C (120°) (22) (2) B B CONNECTOR SERIES NO. 78127**25 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2016/04/04 2016/08/01 2016/08/02 (⌀21) (⌀13) GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 1.0 ° 107065 NASANUMA YKOBAYASHI02 KMORIKAWA DETAIL "E" RELEASE STATUS FORMAT: tb-prod-A3 REVISION: F DATE: 2015/11/16 9 P1 RELEASE DATE 02.08.2016 8 A 00:40:34 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A 4 PLACES ± 0.1 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 2:1 DRWN BY DATE 2016/04/04 NASANUMA 2016/08/01 YKOBAYASHI02 APPR BY A DATE KMORIKAWA DRAWING SIZE 0.5 FPC CONN. N-ZIF ST AU EMBS TP PKG DATE CHK'D BY 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781270002 3 CUSTOMER 2 PSD 1 OF 3 000 1 9 7 8 5 6 4 3 2 1 ELV&RoHS COMPLINT 引き出し方向 E �D� F �E� F ±0.3 �C� �D� TOP TAPE ポケット中心 POCKET OF CENTER CONNECTOR (78119-**15) G D E 14.1 13.6 13.1 12.6 12.1 11.6 11.1 11.5 10.6 10.1 9.6 9.1 8.6 8.1 7.6 7.1 6.6 6.1 5.6 7.5 5.1 4.6 4.1 3.6 3.1 �C� PULL OUT DIRECTION G 24 �5.1� C (PITCH) 4 ⌀ 1.5 +0.1 -0 SECTION F-F F 8 1.75 0.4 ±0.05 40 ±0.2 累積ピッチ ACCUMULATIVE PITCH �3.65� �3.45� �4� 16 B SECTION G-G F TAPE WIDTH 15.8 15.3 14.8 14.3 13.8 13.3 12.8 29.4 25.4 12.3 11.8 11.3 10.8 10.3 9.8 9.3 8.8 8.3 7.8 7.3 6.8 21.4 17.4 6.3 5.8 5.3 4.8 D E C 781272820 28 781272720 27 781272620 26 781272520 25 781272420 24 D 781272320 23 781272220 22 781272120 21 781272020 20 781271920 19 781271820 18 781271720 17 781271620 16 781271520 15 C 781271420 14 781271320 13 781271220 12 781271120 11 781271020 10 781270920 9 781270820 8 7 781270720 B 781270620 6 EMBOSSED PACKAGE A CIRCUIT オーダー番号 ORDER NO CONNECTOR SERIES NO. 78127**25 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2016/04/04 2016/08/01 2016/08/02 16mm, 24mm幅キャリアテープ ANGULAR TOL ± 1.0 ° 107065 NASANUMA YKOBAYASHI02 KMORIKAWA 16mm, 24mm WIDTH CARIER TAPE RELEASE STATUS 9 P1 RELEASE DATE 02.08.2016 8 A 00:40:34 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 GENERAL TOLERANCES (UNLESS SPECIFIED) 4 PLACES ± 0.1 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 4:1 DRWN BY DATE 2016/04/04 NASANUMA 2016/08/01 YKOBAYASHI02 APPR BY A DATE KMORIKAWA DRAWING SIZE 0.5 FPC CONN. N-ZIF ST AU EMBS TP PKG DATE CHK'D BY 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781270002 3 CUSTOMER 2 PSD 2 OF 3 000 1 9 7 8 5 6 引き出し方向 2 1 ELV&RoHS COMPLINT �0.6� DETAIL 1 C TOP TAPE �3.65� E �3.45� � 4� E 3 �5.62� CONNECTOR (78119-**15) PULL OUT DIRECTION 4 E DETAIL 1 SCALE 10:1 C 8 (PITCH) 1.75 0.4 5.1 ⌀ 1.5 SECTION C-C D 1.5 +0.1 -0 0.2 ±0.05 E �C� �D� ポケット中心 POCKET OF CENTER �14.2� 28.4 32 ±0.3 D �C� �D� SECTION E-E +0.1 -0 4 18.1 17.6 17.1 16.6 16.1 C 32 40 ±0.2 　累積ピッチ ACCUMULATIVE PITCH C 19.8 19.3 18.8 18.3 37.4 33.4 17.8 15.6 17.3 15.1 16.8 14.6 16.3 B TAPE WIDTH D C A B 781273620 36 781273520 35 781273420 34 781273320 33 781273220 32 781273120 31 781273020 30 B 781272920 29 EMBOSSED PACKAGE CIRCUIT オーダー番号 ORDER NO CONNECTOR SERIES NO. 78127**25 2016/04/04 2016/08/01 2016/08/02 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 32mm幅キャリアテープ 107065 NASANUMA YKOBAYASHI02 KMORIKAWA ANGULAR TOL ± 1.0 ° 32mm WIDTH CARRIER TAPE RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 02.08.2016 8 A 00:40:34 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A GENERAL TOLERANCES (UNLESS SPECIFIED) 4 PLACES ± 0.1 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 4:1 DRWN BY DATE 2016/04/04 NASANUMA 2016/08/01 YKOBAYASHI02 APPR BY A DATE KMORIKAWA DRAWING SIZE 0.5 FPC CONN. N-ZIF ST AU EMBS TP PKG DATE CHK'D BY 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781270002 3 CUSTOMER 2 PSD 3 OF 3 000 1 E 7 8 5 6 C B 4 3 0.35 L A M 3.05 4.1 D L �0.2� E ELV&RoHS COMPLIANT E D ⏥ 0.1 ⌖ 0.15 X 0.8 1.8 C 0.8 3.4 C M 1 1. 使用材料 MATERIALS 　　ハウジング　　：液晶ポリマー（LCP) 　　　　　　　　　　ガラス充填、UL94V-0(黒色） 　　端子　　　　　：リン青銅　t=0.2mm 　　HOUSING　　　:LIQUID CRYSTAL POLYMAER（LCP) 　　　　　　　　　　GLASS FILLED, UL94V-0, BLACK 　　TERMINAL:PHOSPHOR BRONZE t=0.2mm 2. メッキ仕様 PLATING 端子 TERMINAL テール部：金メッキ 接点部：金メッキ　0.1μm以上 下地：ニッケルメッキ　1.0μm以上 TAIL　AREA :Gold PLATING CONTACT AREA:Gold PLATING 0.1MICRO METER MINIMUM UNDER PLATING:Nickel PLATING 1.0 MICROMETER MINIMUM 3. 端子の平坦度はテール部にて0.1mm以下とする。 COPLANALITY OF SOLDER TAILS:0.1mmMAX. 4. N:極数　N:CIRCUIT 0.7 :PICK UP AREA 2 NOTES X 1.4 9 B (PITCH) 9 CONNECTOR SERIES NO. 78127**25 �1.29� 2016/04/05 2016/08/01 2016/08/02 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION RELEASE DATE 02.08.2016 8 107065 NASANUMA YKOBAYASHI02 KMORIKAWA EC NO: DRWN: CHK'D: APPR: (接点位置） (CONTACT POSITION) �1.67� (接点位置） (CONTACT POSITION) SECTION M-M SECTION L-L A 00:40:37 7 6 5 REV P1 ISO VIEW (参考） ⌖ 0.15 X GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 1.0 ° �1.42� (FPC挿入深さ） (INSERTION �2.7� DEPTH OF FPC) RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 �0.2� D �1.29� A B 0.75 0.5 4 PLACES ± 0.1 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 10:1 DRWN BY DATE 2016/04/05 NASANUMA 2016/08/01 YKOBAYASHI02 APPR BY A DATE KMORIKAWA DRAWING SIZE 0.5 PITCH NON-ZIF CONN. SMT ST ASSY AG DATE CHK'D BY 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781271002 3 CUSTOMER 2 PSD 1 OF 3 000 1 9 7 8 6 5 4 3 2 ELV & RoHS COMPLIANT 適合FPC/FFC推奨寸法 M P S 0.3 ±0.05 M 仕上がり厚さ THICKNESS Tp=(N-1)×0.5 D D 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 導体部：　銅箔(35μmか50μm) COPPER FOIL (35μm or 50μm) 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 補強板：ポリエステル系 REINFORCE BOARD: PET カバーレイ　:　ポリイミド(25μm) COVER FILM: POLYIMIDE(25μm) 導体部：　銅箔(35μm) COPPER FOIL (35μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド(25μm) BASE FILM: POLYIMIDE(25μm) FPC/FFCについて 打抜き方向は導体側から補強版側を推奨します。 導体部については軟箔銅35μmまたは、50μmを推奨いたします。 接着剤の接点部への付着は導通不良の原因になりますので、染み出し無きことを推奨いたします。 FPC/FFCに規定された定格温度が、FPC/FFC単体前提である場合が御座います。 コネクタと組み合わせての実使用において、接着層が劣化する等の信頼性を満足できないケースを回避する為、 C 実機での評価／確認をお願い致します。 ABOUT FPC/FFC RECOMMENDED PUNCHING DIRECTION:FROM CONDUCTOR SIDE TO STIFFENER SIDE. RECOMMENDED CONDUCTOR SPEC:SOFT COPPER FOIL. RECOMMENDED CONDUCTOR THICKNESS:35 MICROMETER OR 50 MICROMETER. RECOMMENDED PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND BECAUSE THERE IS A POSSIBILITY THAT EXTRA ADHESIVE CAUSES THE DEFECT IN ELECTRICAL CONTINUITY. THE HEAT RESISTANCE OF FPC/FFC IS ONLY FPC/FFC SPEC. TO PREVENT THE CASE THAT RELIABILITY CANNOT BE SATISFIED (THE ADHESIVE IS B DETERIORATED etc,)PLEASE DO THE EVALUATION AND THE CONFIRMATION WITH ACTUAL CONNECTOR. FPC構成推奨仕様 FFC構成推奨仕様 FPCについて STRUCTURE OF FPC STRUCTURE OF FFC 補強フィルム材は、ポリイミドを推奨します。ベースフィルムは25μmを推奨します。 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 接着剤は熱硬化接着剤を推奨します。 DIMENSION UNITS SCALE GENERAL ABOUT FPC TOLERANCES MM 12:1 (UNLESS SPECIFIED) RECOMMENDED STIFFENER MATERIAL:POLYIMIDE. DRWN BY DATE ANGULAR TOL ± 1.0 ° RECOMMENDED BASE FILM THICKNESS:25 MICROMETER. 2016/04/05 NASANUMA ± 0.1 4 PLACES RECOMMENDED ADHESIVE:THERMOSETTING ADHESIVE. 0.5 PITCH NON-ZIF CONN. SMT ST ASSY AG 107065 NASANUMA YKOBAYASHI02 KMORIKAWA 2016/04/05 2016/08/01 2016/08/02 B (N+1)×0.5 ±0.07 補強板：ポリイミド REINFORCE BOARD: POLYMIDE 熱硬化接着剤 THERMOSETTING ADHESIVE C めっき：金めっき(0.1μm以上) 下地ソフトニッケル(1-5μm) PLATING:GOLD(0.1μm MIN.) SOFT NICKEL UNDER(1-5μm) TYP(2). (FPC ONLY) E 0.35 +0.04 S 0.30 +0.05 - 0.03 - 0.02 P 0.50±0.03 0.50±0.02 M 0.50±0.10 0.50±0.12 Tp Tp±0.03 Tp±0.03 FFC FPC めっき：金めっき(0.1μm以上) 下地ソフトニッケル(1-5μm) PLATING:GOLD(0.1μm MIN.) SOFT NICKEL UNDER(1-5μm) R 0.30 APPLICABLE FPC/FFC RECOMMENDED DIMENSION 補強板 (STIFFENER BOARD) 3.00 MIN. 4.00 MIN. E 1 RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 9 P1 RELEASE DATE 02.08.2016 8 A 00:40:37 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DATE CHK'D BY 2016/08/01 YKOBAYASHI02 APPR BY KMORIKAWA DRAWING SIZE A DATE 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781271002 3 CUSTOMER 2 PSD 2 OF 3 000 1 9 7 8 5 6 4 3 2 1 ELV & RoHS COMPLIANT B 19.6 19.1 18.6 18.1 17.6 17.1 16.6 16.1 15.6 15.1 14.6 14.1 13.6 13.1 12.6 12.1 11.6 11.1 10.6 10.1 9.6 9.1 8.6 8.1 7.6 7.1 6.6 6.1 5.6 5.1 4.6 E D C B A 781273620 781273520 781273420 781273320 781273220 781273120 781273020 781272920 781272820 781272720 781272620 781272520 781272420 781272320 781272220 781272120 781272020 781271920 781271820 781271720 781271620 781271520 781271420 781271320 781271220 781271120 781271020 781270920 781270820 781270720 781270620 EMBOSSED PACKAGE オーダー番号 ORDER NO. 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 E B ±0.05 1.6 ±0.1 17.5 17 16.5 16 15.5 15 14.5 14 13.5 13 12.5 12 11.5 11 10.5 10 9.5 9 8.5 8 7.5 7 6.5 6 5.5 5 4.5 4 3.5 3 2.5 D 0.4 ±0.05 B CONNECTOR SERIES NO. 78127**25 CIRCUIT THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 107065 NASANUMA YKOBAYASHI02 KMORIKAWA 9 P1 RELEASE DATE 02.08.2016 8 A 00:40:37 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A RELEASE STATUS C RECOMMENDED PCB LAYOUT GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 1.0 ° FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 参考マスク厚:100μm 参考開口率:100% REFERENCE SCREEN THICKNESS:100 REFERENCE SCREEN OPEN RATIO:100% 0.5 ±0.05 推奨基板レイアウト 2016/04/05 2016/08/01 2016/08/02 C 18.6 18.1 17.6 17.1 16.6 16.1 15.6 15.1 14.6 14.1 13.6 13.1 12.6 12.1 11.6 11.1 10.6 10.1 9.6 9.1 8.6 8.1 7.6 7.1 6.6 6.1 5.6 5.1 4.6 4.1 3.6 1.6 ±0.1 D 17 17 16 16 15 15 14 14 13 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 4.0 ±0.1 E 17 16 16 15 15 14 14 13 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 4 PLACES ± 0.1 3 PLACES ± 0.1 2 PLACES ± 0.1 1 PLACE ± 0.1 0 PLACES ± 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 12:1 DRWN BY DATE 2016/04/05 NASANUMA 2016/08/01 YKOBAYASHI02 APPR BY A DATE KMORIKAWA DRAWING SIZE 0.5 PITCH NON-ZIF CONN. SMT ST ASSY AG DATE CHK'D BY 2016/08/02 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 78127 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER 781271002 3 CUSTOMER 2 PSD 3 OF 3 000 1