0782850001

PRODUCT SPECIFICATION 1.8 INCH SERIAL ATA PLUG 1.0 SCOPE This Product Specification covers the performance requirements of the Serial ATA / High Speed Serialized device plug connector. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) Product Name Part Number SATA PLUG, 1.8 INCH SSD RIGHT ANGLE SMT 78285-0001 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See Sales Drawing SD-78285-001 for information on dimensions, materials, platings and markings. 2.3 SAFETY AGENCY APPROVALS UL FILE: CSA: E29179 (VOLUME 10) 1699307 (LR19980) 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS The following documents form a part of this specification to the extend specified herewith. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In addition, in event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. SATA Specification TENTATIVE RELEASE: THIS SPECIFICATION IS BASED ON DESIGN OBJECTIVES AND IS STRICTLY TENTATIVE. PRELIMINARY TEST DATA MAY EXIST, BUT THIS SPECIFICATION IS SUBJECT TO CHANGE BASED ON THE RESULTS OF ADDITIONAL TESTING AND EVALUATION REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 1 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 4.0 RATINGS 4.1 VOLTAGE 30 Volts Max 4.2 CURRENT 1.5 Amps DC or AC (RMS) Max @ 60 Hz 4.3 TEMPERATURE Operating: - 0°C to + 55°C Non Operating: - 40°C to + 85°C 4.4 HUMIDITY 20% - 80% 4.5 PRESSURE 650 mm – 800 mm Hg 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM 1 2 3 DESCRIPTION Low Level Contact Resistance (LLCR) Contact Current Rating (Power Segment) Insulation Resistance TEST CONDITION Subject mated contacts assembled in housing to 20 mV maximum open circuit at 100 mA maximum. (EIA 364-23) 3 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 30 mΩ MAXIMUM [Initial] 15 mΩ MAXIMUM [Delta change from Initial] Mount connector to a test PCB with ½ oz 1.5 A per pin copper layer. MINIMUM Wire power pins P1, P2, P5 and P6 in parallel for power. Temperature rise shall not Wire ground pins P3 and P4 in parallel for exceed 30°C at any point in the return. connector when contacts are Supply 6A total DC current to the power powered pins in parallel, returning from the parallel ground pins (P3, and P4). Still Air at Ambient temperature Record temperature rise when thermal 25°C equilibrium is reach. Apply a voltage of 500 VDC for 1 minute between adjacent terminals. Measure the insulation resistance for mated and unmated connectors (EIA 364-21) REVISION: ECR/ECN INFORMATION: TITLE: EC No: S2010-0563 REQUIREMENT SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT 1000 MΩ MINIMUM SHEET No. 2 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 4 Dielectric Withstanding Voltage Apply a voltage of 500 VAC for 1 minute between adjacent terminals of mated and unmated connectors. (EIA 364-20 Method B) No breakdown 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 20 N MAXIMUM insertion force 5 Connector Insertion Mate and Unmate connector assemblies and at a rate of 12.5 mm per minute. Removal Forces (EIA 364-13) & 2.5 N MINIMUM removal force [Intial & After 500 cycles] No Physical damage 6 Durability 7 Solder tab Retention Force 8 9 Physical Shock Random Vibration 500 cycles for backplane/blindmate application. All at a maximum rate of 200 cycles per hour. (EIA 364-09) Apply axial pull out force on solder tab in the housing at a rate of 25.4 mm per minute. Subject mated connector to 30 g’s half-sine shock pulses of 11 msec duration. Three shocks in each direction applied along three mutually perpendicular planes for a total of 18 shocks. (EIA 364-27 Condition H) Subject mated connector to 5.35 g’s RMS. 30 minutes in each of the three mutually perpendicular planes. (EIA 364-28 Condition V Test letter A) REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 Meet requirements of additional tests as specified in the test sequence in Section 7.0 4.45 N MINIMUM retention force No Physical damage No discontinuities of 1 µs or longer duration No discontinuities of 1 µs or longer duration SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 3 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.3 ENVIRONMENTAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT No Physical damage 10 Humidity 11 Resistance to Soldering Heat 12 Solderability Subject the connector to temperature and humidity of 40°C at 95% RH for 96 hours. (EIA 364-31 Method II Test Condition A) Refer to Section 9.0 for soldering profile Meet requirements of additional tests as specified in the test sequence in Section 7.0 No damage in appearance of connector Solder Time : 3 ± 0.5 seconds Solder Temperature : 260 ± 5°C 95% MIN Solder coverage No Physical damage 13 Temperature Life Subject mated connector to temperature life at +85°C for 500 hours. (EIA 364-17 Test Condition III Method A) Meet requirements of additional tests as specified in the test sequence in Section 7.0 No Physical damage 14 15 Thermal Shock Subject connector to 10 cycles between -55°C and +85°C. (EIA 364-32 Test Condition I) Mixed Flowing Gas Half of the samples are exposed unmated for 7 days, then mated for the remaining 7 days. The other half of the samples mated for full 14 days test period. (EIA 364-65, Class 2A) Meet requirements of additional tests as specified in the test sequence in Section 7.0 No Physical damage Meet requirements of additional tests as specified in the test sequence in Section 7.0 6.0 PACKAGING Refer to Sales Drawing SD-78285-001 for packing details. REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 4 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 7.0 TEST SEQUENCES Test Group
A B C D E F G Examination of the connector(s) 1, 5 1, 9 1, 8 1, 8 1, 7 1 1, 5 Low Level Contact Resistance (LLCR) 2, 4 3, 7 2, 4, 6 H Test or Examination  4, 6 Insulation Resistance 2, 6 Dielectric Withstanding Voltage 3, 7 Current Rating 7 Insertion Force 2 2 Removal Force 8 4 Durability 3 4(a) Physical Shock 6 Vibration 5 2(a) Humidity 3 5 Temperature Life 3 Reseating (manually unplug/plug three times) 5 5 Mixed Flowing Gas 3 Thermal Shock 4 Resistance to Soldering Heat 3 Solder Tab Retention Force 2, 4 Solderability 1 Note – (a) Preconditioning, 50 cycles for the 500-durability cycles requirement. The insertion and removal cycle is at a maximum rate of 200 cycles per hour. REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 5 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 8.0 VIBRATION/SHOCK TEST SET-UP REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 6 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 9.0 SOLDERING PROFILE Description Average Ramp Rate Preheat Temperature Preheat Time Ramp to Peak Time over Liquidus (217°C) Peak Temperature Time within 5°C of Peak Ramp - Cool Down Time 25°C to Peak REVISION: ECR/ECN INFORMATION: TITLE: 3 EC No: S2010-0563 DATE: 2010/01/18 DOCUMENT NUMBER: PS-78285-002 Requirement 3°C/sec Max 150°C Min to 200°C Max 60 to 180 sec 3°C/sec Max 60 to 150 sec 260 +0/-5°C 20 to 40 sec 6°C/sec Max 8 min Max SERIAL ATA PLUG 1.8 INCH SSD RIGHT-ANGLE SMT SHEET No. 7 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Victor Lim 2010/01/18 Colynn Goh 2010/01/27 B.O Kok 2010/01/27 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC