0787580001

PRODUCT SPECIFICATION SAS/ PCIe RIGHT ANGLE SMT PLUG 1.0 SCOPE This Product Specification covers the performance requirements of the SAS/PCIe High Speed Serialized Plug connector. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) Product Name Part Number SAS/PCIE, RIGHT ANGLE SMT PLUG (30” GOLD) SAS/PCIE, RIGHT ANGLE SMT PLUG (15” GOLD) 78758-0001 78758-0002 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See Sales Drawing SD-78758-001 for information on dimensions, materials, platings and markings. 2.3 SAFETY AGENCY APPROVALS UL FILE CSA : : E29179 VOL 10 1699307 (LR 19980) REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 1 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS See the Sales Drawing and other sections of this Specification for the necessary referenced Documents and Specifications. 4.0 RATINGS 4.1 VOLTAGE 30 Volts Max. 4.2 CURRENT Power section (per pin): - Continuous Current 1.5A - Peak Current 2.5A 1.5s - Peak Current Pre-charge 6A 1ms - Signal section (per pin): Continuous current 500mA 4.3 TEMPERATURE Operating: 0°C to + 55°C Non-Operating: -40°C to + 85°C 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM 1 DESCRIPTION Low Level Contact Resistance (LLCR) Temperature Rise (via current cycling) 2 (Power Segment, P1 thru P15) TEST CONDITION REQUIREMENT Subject mated connectors to a maximum voltage of 20 mV and a current of 100 mA. (EIA 364-23) 30 m MAXIMUM [initial] Delta Change 15 m MAXIMUM From Initial Value Mount connector to a test PCB with ½ oz copper layer. 1.5 A per pin Wire power pins P1, P2, P8 and P9 in MINIMUM parallel for power. Wire ground pins P4, P5, P6, P10 and Temperature rise shall not P12 in parallel for return. exceed 30°C at any point in the Supply 6A total DC current to the power connector when contacts are pins in parallel, returning from the parallel powered ground pins. Measure and record temperature after 96 Still Air at Ambient temperature hours (45 minutes ON and 15 minutes 25±3°C OFF per hour). REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 2 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 3 Insulation Resistance 4 Dielectric Withstanding Voltage After 500 VDC for 1 minute, measure the insulation resistance between adjacent terminals of the mated and unmated connector assemblies. (EIA 364-21) 1000 Megohms MINIMUM Subject a voltage of 500 VAC for 1 minute between adjacent terminals of mated and unmated connector at sea level. (EIA 364-20) No breakdown 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT MAXIMUM Mate force 59 N 5 Connector Insertion Mate and Unmate connector assemblies and at a rate of 25 mm per minute. Removal Forces (EIA 364-13) & MINIMUM Unmate force 5 N for Backplane Receptacle [At Initial and After Durability] No Physical damage 6 Durability 7 Terminal Retention Force 8 Resistance to Soldering Heat 500 cycles for Backplane Receptacle, 25cycles for Cable. All at a maximum rate of 200 cycles per hour. (EIA 364) Delta Change 15 m MAXIMUM From Initial Value Meet requirements of additional tests as specified in the test sequence in Section 7.0 Port 1: 0.7lbf (0.32kgf) MIN retention force Port 2: 0.49lbf (0.22kgf) MIN retention force Apply axial pull out force on terminal in the housing at a rate of 25.4 mm per minute. Refer to Section 9.0 for Soldering Profile No Damage in appearance of Connector REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 3 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION No Physical damage 9 10 Physical Shock Random Vibration Subject mated connector to 50 g’s half-sine shock pulses of 11 msec duration. Three shocks in each direction applied along three mutually perpendicular planes for a total of 18 shocks. (EIA 364-27 Condition A) Delta Change 15 m MAXIMUM From Initial Value No discontinuities of 1 s or longer duration Delta Change 15 m MAXIMUM From Initial Value Subject mated connector to 3.10 g’s RMS between 20-500Hz for 15 minutes in each of the three mutually perpendicular planes. (EIA 364-28 Condition VII Test letter D) No discontinuities of 1 s or longer duration 5.3 ENVIROMENTAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT No Physical damage 11 Humidity Delta Change 15 m MAXIMUM From Initial Value Subject the connector to temperature and humidity of 40°C with 90% to 95% RH for 96 hours. (EIA 364-31 Method II Test Condition A) Meet requirements of additional tests as specified in the test sequence in 12 Solderability Solder paste is deposited on a ceramic plate via stencil. The connectors are steam aged and placed onto the solder paste print. The substrate is processed through No Bridging and a forced hot convection oven. The 95% solder coating coverage connectors are removed from the ceramic and inspected Steam Aging: 8hr. No Physical damage 13 Temperature Life Delta Change 15 m MAXIMUM From Initial Value Subject mated connector to temperature life at +85°C for 500 hours. (EIA 364-17 Test Condition III Method A) Meet requirements of additional tests as specified in the test sequence in Section 7.0 REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 4 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION No Physical damage 14 Thermal Shock Delta Change 15 m MAXIMUM From Initial Value Subject connector to 10 cycles between -55°C and +85°C. (EIA 364-32 Test Condition I) Meet requirements of additional tests as specified in the test sequence in Section 7.0 No Physical damage 15 1 half of samples are exposed unmated (receptacle only) for 7 days and then mated for additional 7 days. Mixed Flowing Gas The other half of samples mated for full 14 days test period. (EIA 364-65, Class 2A) Delta Change 15 m MAXIMUM From Initial Value Meet requirements of additional tests as specified in the test sequence in Section 7. 6.0 PACKAGING Refer to Packing Specification, PK-78758-001 (Tape and Reel) for packaging details. REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 5 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 7.0 TEST SEQUENCES Test Group  A B C D E F G Examination of the connector(s) 1, 5 1,10 1,7 1,6 1,9 1,10 1 Low Level Contact Resistance (LLCR) 2, 4 2,5,7 2,5,7,9 H I J Test or Examination  2,5,7,9 2,4,6 Insulation Resistance 3,6 Dielectric Withstanding Voltage 4,7 1,7 5 Temperature Rise Insertion Force 2,5 Removal Force 3,6 3 Durability 3(a) Physical Shock 8 Vibration 6 3(a) 2(a) 3(a) 3(a) 6 Humidity Temperature Life 1 (b) 4 5 5 (b) 3 Reseating (manually unplug/plug three times) 4 4 4 8 4 Thermal Shock 2 Terminal retention force Resistance to Soldering Heat 2 1 Solderability 6 Mixed Flowing Gas Note – (a) Preconditioning, 50 cycles for the 500-durability cycles requirement. The insertion and removal cycle is at a maximum rate of 200 cycles per hour. (b) Preconditioning, 105°C for 72 hours REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 6 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 8.0 VIBRATION/SHOCK TEST SET-UP SAS/PCIe Receptacle mated with SAS/PCIe Plug (For Reference Only) SAS Receptacle PC Board Nut Angle Plate Fixture Screw SAS Plug Screw PC Board Spacer Mounting Fixture Vibration / Shock Table REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 7 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 9.0 SOLDERING PROFILE Description Average Ramp Rate Preheat Temperature Preheat Time Ramp to Peak Time over Liquidus (217°C) Peak Temperature Time within 5°C of Peak Ramp - Cool Down Time 25°C to Peak Requirement 3°C/sec Max 150°C Min to 200°C Max 60 to 180 sec 3°C/sec Max 60 to 150 sec 260 +0/-5°C 20 to 40 sec 6°C/sec Max 8 min Max REVISION: ECR/ECN INFORMATION: TITLE: A EC No: S2015-0930 DATE: 2015/02/18 DOCUMENT NUMBER: PS-78758-001 SHEET No. SAS/ PCIe RIGHT ANGLE SMT PLUG 8 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Cynthia Wang ML Ong SH Ong TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC