08-65-0815

19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 NOTES: 1. MATERIAL: (0.20)/.008 THICK PHOS BRONZE 2. FINISH: 222 - OVERALL MATTE TIN: (0.00254)/.000100 MIN. TIN OVER (0.00127)/.000050 MIN NICKEL P909 - OVERALL HOT TIN DIP: (0.00254)/.000100 MIN. 231 - SELECT GOLD: (0.00127)/.000050 MIN. SELECT MATTE TIN: (0.00254)/.000100 MIN. OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 MIN. 550 - SELECT GOLD: (0.00038)/.000015 MIN. OVERALL GOLD FLASH: (0.00005)/.000002 MIN. OVERALL NICKEL UNDERPLATE: (0.00076)/.000030 MIN. 555- SELECT GOLD (0.00038)/.000015 MIN. OVERALL NICKEL UNDERPLATE: (0.00076)/.000030 558 - SELECT GOLD: (0.00076)/.000030 MIN. OVERALL GOLD FLASH: (0.00005)/.000002 MIN. OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 MIN. 561- SELECT GOLD (0.00076)/.000030 MIN. OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 3. PRODUCT SPEC: PS-10-07 4. PACKAGING SPECIFICATION: LOOSE TERMINALS: PER PK-2759-001 CHAIN FORM TERMINALS: PER PK-2759-002 5. CRIMP IS FOR 22-30 GA WIRE WITH (1.57)/.062 DIA INSULATION MAX. 6. INSERTION FORCE OF TERMINAL INTO (2.54)/.100 CENTERLINE CONNECTOR IS 2.5 LBS. MAX 7. TERMINAL RETENTION IN HOUSING IS 26.7N / 6LBS MIN. WHEN PULLED AT THE RATE OF (25.4MM)/ 1 INCH PER MINUTE. 8. DIMENSIONS GIVEN ACROSS CENTERLINES ARE SYMMETRICAL ABOUT THOSE CENTERLINES WITHIN HALF THE TOTAL TOLERANCE. 9. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002 L K J H L K J H G G F F E E 1.98 1.85 .078 .073 D D C C FACTORY I.D. SEE NOTE 2 SYMBOLS = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 1:1 = 0 B GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 = 0 = 0 A MM ± 3 PLACES ± ± FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 19 18 RELEASE DATE 17 2018/10/05 16 09:56:23 C 15 14 13 12 11 10 9 8 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± = 0 1 PLACE = 0 0 PLACES ± = 0 P1 INCH 4 PLACES ± ANGULAR TOL DOCUMENT STATUS CURRENT REV DESC: NOTE 4 UPDATED ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS = 0 7 6 B EC NO: 605479 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 5 2018/09/07 2018/10/05 2018/10/05 KK (2.54)/.100 CRIMP TERMINAL, 22-30 GA WIRE SAME AS 2759 EXCEPT MATL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1992/01/21 2012/03/20 DRAWING SERIES D-SIZE 6459 4 SD-6459 MATERIAL NUMBER SEE CHART 3 PSD 001 H2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 1 OF 2 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L L K K J J H H G G F F E E D D C C SYMBOLS = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 1:1 = 0 B GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 = 0 = 0 A MM ± 3 PLACES ± ± FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 19 18 RELEASE DATE 17 2018/10/05 16 09:56:23 C 15 14 13 12 11 10 9 8 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± = 0 1 PLACE = 0 0 PLACES ± = 0 P1 INCH 4 PLACES ± ANGULAR TOL DOCUMENT STATUS CURRENT REV DESC: NOTE 4 UPDATED ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS = 0 7 6 B EC NO: 605479 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 5 2018/09/07 2018/10/05 2018/10/05 KK (2.54)/.100 CRIMP TERMINAL, 22-30 GA WIRE SAME AS 2759 EXCEPT MATL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1992/01/21 2012/03/20 DRAWING SERIES D-SIZE 6459 4 SD-6459 MATERIAL NUMBER SEE CHART 3 PSD 001 H2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 2 OF 2 1 A