12
H
G
11
10
9
7
8
ASSEMBLY NOTES:
1. SLIDE COMPONENTS ONTO CABLE AS SHOWN
REF. ITEMS 1, 2 & 4 ARE PRE-ASSEMBLED
2. CABLE PREP: SEE SHEET 2
3. PULL TERMINATED RJ45 PLUG (#7) INTO PLUG HOLDER (#4)
WITH LOCKING TAB ALIGNED WITH SLOT ON PLUG HOLDER
DEPRESS LOCKING TAB DOWN BEFORE SEATING PLUG
INTO FINAL POSITION
4. INSTALL RETAINER WEDGE (#5) INTO SLOT LOCATED ON
UNDERSIDE OF PLUG HOLDER (#4), SEE DETAIL B
5. ROTATE SEAL NUT UNTIL CABLE SEAL IS TIGHT ON OUTER JACKET OF CABLE
6. SLIDE COUPLING RING (#3) INTO POSITION SHOWN ON ASSEMBLY VIEW
5
6
4
3
2
1
3
H
1
LOCKING TAB SLOT
4
DRAIN WIRE AND
BRAIDED SHIELD
SEE SHT-2
BAYONET LOCKING FEATURE
G
8
SEAL NUT
(NOTE 5)
MATERIAL & FINISH NOTES:
1. MATERIAL: SEE BOM TABLE
2. FINISH: SEE BOM TABLE
3. PACKAGING: PARTS ARE PACKED IN A CLEAR POLY BAG
WITH LABEL AND ASSEMBLY INSTRUCTIONS
LOCKING TAB
5
F
F
6
2.12
53.8
.66
16.7
FLATS
E
7
E
.52
13.3
2
LOCKING TAB
A
LOCKING TAB
(NOTE 3)
CABLE
1.28
32.5
.59 HEX
15.0
D
D
RETAINER TAB
ENGINEERING SPECS:
1. WIRE RANGE:
OD: .217 IN [5.51mm] TO .256 IN [6.50mm]
CONDUCTOR TYPE: SOLID OR STRANDED
CONDUCTOR RANGE: 22 TO 28 AWG
CONDUCTOR OD RANGE: .037 IN [0.94mm] TO .042 IN [1.07mm]
C
B
B
SECTION A-A
A
.71
18.0
ASSEMBLY VIEW
C
2. ELECTRICAL SPECS (RJ45)
A. VOLTAGE: 30VAC/42VDC
B. CURRENT: 1.5 AMPS
C. OPERATING TEMP: -40°C TO +85°C [-40°F TO +185°F]
3. DIMS SHOAWN ARE FOR REFERENCE ONLY UNLESS
NOTED OR TOLERANCED OTHERWISE
NOTE: INSTALL RETAINER WITH
RETAINER TAB FACING IN AS SHOWN
(NOTE 4)
DETAIL B
SCALE 4:1
B
A
8
7
6
5
4
3
2
1
ITEM
LOAD BAR
RJ-45 PLUG (SHIELDED)
GASKET SEAL (MATING)
RETAINER WEDGE
PLUG HOLDER
COUPLING RING (BAYONET LOCK)
O-RING
CABLE SEAL ASSEMBLY
DESCRIPTION
DOCUMENT STATUS
12
FORMAT: Eng-lega-master-tb-prod-C
REVISION: E1
DATE: 2021/05/01
P1
RELEASE DATE
11
2022/01/24
10
POLYCARBONATE
POLYCARBONATE/PHOS-BRZ
NITRILE
PBT
PBT
PBT
NITRILE
NYLON SHELL/TPE GLAND
MATERIAL
6
CLEAR
CLEAR/GOLD PLATE
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
FINISH
FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SCALE
SYMBOLS DIMENSION UNITS
CURRENT REV DESC: REDRAWN TO NX, BOM
UPDATED FOR PACKAGING AND LABELS, UPDATE
= 0
NOTES, ADD NOTE 3 TO ELECTRICAL SPECS. ADD
TOLERANCES TO STEPS A,C & D (SHT-2)
GENERAL TOLERANCES
1.5:1
INCH/MM
=
0
(UNLESS SPECIFIED)
MM
=
0
INCH
4 PLACES ±
±
3 PLACES ±
±
DIVISIONAL
SYMBOLS 2 PLACES ±
±
±
±
0 PLACES ±
±
1 PLACE
ANGULAR TOL
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
23:05:01
9
8
7
B
6
5
°
EC NO: 692535
DRWN: RSTONE
CHK'D: CCHRASTKA
APPR: BWOODMAN
INITIAL REVISION:
DRWN: RSTONE
APPR: JFMURPHY
THIRD ANGLE PROJECTION
4
2022/01/14
2022/01/20
2022/01/24
RJ-45 PLUG ASSEMBLY
FIELD ATTACHABLE
PRODUCT CUSTOMER DRAWING
DOC TYPE DOC PART REVISION
DOCUMENT NUMBER
2013/03/19
2013/06/24
DRAWING
SERIES
C-SIZE
84700
3
SD-84700-012
MATERIAL NUMBER
PSD 001
CUSTOMER
847000002
GENERAL MARKET
2
B
SHEET NUMBER
1 OF 2
1
A
12
10
11
9
7
8
5
6
4
3
2
1
DRAIN WIRE
SHIELD (FOIL OR BRAIDED WIRE)
H
H
CABLE PREP.
A. STRIP OUTER INSULATION TO DIMENSION SHOWN
B. FOLD DRAIN WIRE AND OR BRAIDED SHIELD (SEE REF. NOTE)
BACK OVER OUTER JACKET
C. TRIM WIRES (STRAIGHT) TO DIMENSION SHOWN
D. TRIM DRAIN WIRE AND OR SHIELD TO DIMENSION SHOWN. SLIDE LOAD BAR
ON TO WIRES TO DIMENSION SHOWN
E. TRIM WIRES AHEAD OF LOAD BAR TO DIMENSION SHOWN
F. ALIGN RJ45 PLUG(#7) AND INSERT PREPARED CABLE INTO
BACK OF RJ45 PLUG UNTIL WIRES ARE SEATED
G. CRIMP WIRES TO PLUG USING RECOMMENDED HAND TOOL
SENTINEL CONNECTOR SYSTEMS P/N: 900000/900208 OR 900005/900216-1
STEP-A
1.00 +.06
-.00
B
25.4 +1.5
0.0
G
DRAIN WIRE
SHIELD (FOIL OR BRAIDED WIRE)
STEP-B
G
F
F
STEP-C
E
E
.75 ±.03
19.0 ±0.8
B
D
REF. NOTE: CABLE PREP STEPS MAY VARY DEPENDING
ON TYPE OF CABLE SHIELDING
B
LOAD BAR (#8)
.50 ±.03
12.7 ±0.8
RJ45 PLUG (#7)
LOAD BAR (#8)
D
STEP-D
C
B
.08
.06
2.0
1.5
C
STEP-E
B
B
FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SCALE
SYMBOLS DIMENSION UNITS
CURRENT REV DESC: REDRAWN TO NX, BOM
UPDATED FOR PACKAGING AND LABELS, UPDATE
= 0
NOTES, ADD NOTE 3 TO ELECTRICAL SPECS. ADD
TOLERANCES TO STEPS A,C & D (SHT-2)
GENERAL TOLERANCES
.30
.32
7.6
8.1
INCH/MM 1:1
=
DOCUMENT STATUS
12
FORMAT: master-tb-prod-C
REVISION: J1
DATE: 2021/05/01
P1
RELEASE DATE
11
2022/01/24
10
(UNLESS SPECIFIED)
ANGULAR TOL
±
4 PLACES
±
DIVISIONAL 3 PLACES
SYMBOLS
±
2 PLACES
±
=
A
0
0
1 PLACE
±
0 PLACES
±
°
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
23:05:01
9
8
7
6
5
EC NO: 692535
DRWN: RSTONE
CHK'D: CCHRASTKA
APPR: BWOODMAN
INITIAL REVISION:
DRWN: RSTONE
APPR: JFMURPHY
THIRD ANGLE PROJECTION
4
2022/01/14
2022/01/20
2022/01/24
RJ-45 PLUG ASSEMBLY
FIELD ATTACHABLE
PRODUCT CUSTOMER DRAWING
DOC TYPE DOC PART REVISION
DOCUMENT NUMBER
2013/03/19
2013/06/24
DRAWING
SERIES
C-SIZE
84700
3
SD-84700-012
MATERIAL NUMBER
PSD 001
CUSTOMER
847000002
GENERAL MARKET
2
B
SHEET NUMBER
2 OF 2
1
A
