0872632893

9 7 8 5 6 4 3 2 1 �1.30� HEIGHT CONTACT 2.80 E 0.30 0.50 (2X) 0.30 ±0.08 ⌓ 0.10 SEE NOTE 3 6.20 PART NO. LEGEND 0.50 ±0.05 ⌖ 0.20Ⓜ XⓂ 87263 - **** PLATING OPTION 3 - 0.38µm MIN. GOLD 5 - 0.76µm MIN. GOLD 6 - (0.13-0.38)µm GOLD FLASH CIRCUIT SIZE 2.00 4.20 D PACKAGING 0 – W/CAP IN TUBE (SEE SHEET 2) 2 – W/O CAP IN TUBE (SEE SHEET 2) 8 – W/O CAP IN TAPE & REEL (SEE SHEET 3) 9 – W/CAP IN TUBE & REEL (SEE SHEET 3) SQ. 0.65 (TYP) 2.00 (TYP) DIM A -X- DIM B DIM. A DIM. B 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00 22.00 24.00 26.00 28.00 30.00 32.00 34.00 36.00 38.00 40.00 42.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00 22.00 24.00 26.00 28.00 30.00 32.00 34.00 36.00 38.00 40.00 42.00 44.00 E D 5.95 DIM B 4.90 C PARTS TO BE PACK WITH CAP (12 CKT SHOWN) A B 2.00 (TYP) ⌀1.60 ±0.05 (2X) 7.00 C NOTES: 1. FOR ILLUSTRATION PURPOSES, DRAWINGS SHOWS PART WITH 12 CIRCUIT SIZE 2. PLATING: POST PLATING - SELECTIVE GOLD (SEE LEGEND) AT CONTACT AREA, AND 1.27µm MIN. SELECTIVE TIN AT SOLDER AREA BOTH OVER 1.27µm MIN. NICKEL OVERALL 3. CO-PLANARITY OF P.C TAIL TO BE MEASURED BY RESTING THE PART ON A FLAT GAGE SURFACE. 4. PRODUCT SPECIFICATION PS-87263 APPLIES 5. CAP: HIGH TEMPERATURE THERMOPLASTIC, UL RATED 94V-0, SUITABLE FOR SURFACE-MOUNT SOLDERING PROCESS. COLOR: BLACK 6. POSITION OF CAP TO BE CENTRAL WITH RESPECT TO DIMENSION "A" 7 . CONTACT FACTORY FOR DETAIL ON THIS PART NO. 8. PARTS SHALL BE PACKED IN MOISTURE BARRIER BAG 9 . P/N 87263-3686 TO BE PACKED IN EMBOSSED TAPE TYPE B1 10. PACKAGING SPECIFICATION FOR TAPE AND REEL: PK-87263-300 3.65 2.50 (TYP) CKT. SIZE 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 B 2.00 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A DIMENSION UNITS SCALE mm NTS GENERAL TOLERANCES (UNLESS SPECIFIED) 1.50 (TYP) ⌀1.00 ±0.05 (TYP) MM 4 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/10/11 8 ± ± 1 PLACE RECOMMENDED SOLDER PAD DESIGN INCH ± 3 PLACES ± 0.80 (TYP) FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 CURRENT REV DESC: MIGRATED TO ECTR ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:17:35 7 6 5 4 EC NO: 605777 DRWN: RMV02 CHK'D: GJEEVANSURES APPR: ISHWARG INITIAL REVISION: DRWN: JDK APPR: MLONG THIRD ANGLE PROJECTION 3 2018/02/02 2018/10/11 2018/10/11 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/01/11 2010/03/19 SD-87263-XX2X MATERIAL NUMBER DRAWING SERIES A3-SIZE 87263 2 A MGRID, B/ENTRY RECEPT. 2.80MM HT. W/LOC. PEGS W/CAP, SMT SEE TABLE PSD 001 J12 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 4 9 7 8 5 6 4 3 1 CKT. SIZE PART NO. FOR PARTS WITHOUT CAP PART NO. FOR 7 PARTS WITH CAP 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 87263-042* 87263-062* 87263-082* 87263-102* 87263-122* 87263-142* 87263-162* 87263-182* 87263-202* 87263-222* 87263-242* 87263-262* 87263-282* 87263-302* 87263-322* 87263-342* 87263-362* 87263-382* 87263-402* 87263-422* 87263-040* 87263-060* 87263-080* 87263-100* 87263-120* 87263-140* 87263-160* 87263-180* 87263-200* 87263-220* 87263-240* 87263-260* 87263-280* 87263-300* 87263-320* 87263-340* 87263-360* 87263-380* 87263-400* 87263-420* 44 7 87263-442* 87263-440* E �560� �560� 2 D E D C C 10.00 6.00 B B 9.00 10.00 **2 * **0 * P/N 87263- P/N 87263- THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO ECTR GENERAL TOLERANCES (UNLESS SPECIFIED) A MM 4 PLACES ± 3 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/10/11 8 ± ± 1 PLACE FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 INCH ± ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:17:35 7 6 5 4 EC NO: 605777 DRWN: RMV02 CHK'D: GJEEVANSURES APPR: ISHWARG INITIAL REVISION: DRWN: JDK APPR: MLONG THIRD ANGLE PROJECTION 3 2018/02/02 2018/10/11 2018/10/11 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/01/11 2010/03/19 SD-87263-XX2X MATERIAL NUMBER DRAWING SERIES A3-SIZE 87263 2 A MGRID, B/ENTRY RECEPT. 2.80MM HT. W/LOC. PEGS W/CAP, SMT SEE TABLE PSD 001 J12 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 4 9 7 8 ⌀1.50 +0.10 0.00 4.00 6 5 4 2.00 1.75 U E 3 PART NO. FOR 7 PARTS WITH CAP IN T/REEL CKT. SIZE F So W 87263-048* 87263-068* 87263-088* 87263-108* 87263-128* 87263-148* 87263-168* 87263-188* 87263-208* 87263-228* 87263-248* 87263-268* 87263-288* 87263-308* 87263-328* 87263-348* 87263-049* 87263-069* 87263-089* 87263-109* 87263-129* 87263-149* 87263-169* 87263-189* 87263-209* 87263-229* 87263-249* 87263-269* 87263-289* 87263-309* 87263-329* 87263-349* 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 11.5 11.5 11.5 11.5 11.5 11.5 11.5 14.2 20.2 20.2 20.2 20.2 20.2 20.2 26.2 ---- ---------------------28.4 40.4 40.4 40.4 40.4 40.4 40.4 52.4 ---- 24 24 24 24 24 24 24 32 44 44 44 44 44 44 56 ---- 9 87263-368* 87263-369* 36 26.2 52.4 56 87263-388* 87263-408* 87263-389* 87263-409* 38 40 9 87263-3686 ---- 36 W 12.00 �5.40� CUSTOMER PULL OUT DIRECTION SECTION U-U PART NO. 87263-**9* (CKTS 04 TO 16) SINGLE SPROKET HOLE T/REEL - TYPE A D 2.00 4.00 ⌀1.50 +0.10 0.00 �5.40� 1.75 V 1 PART NO. FOR 7 PARTS WITHOUT CAP IN T/REEL F U 2 ------- ------- T/REEL TYPE A E B D ------- 56 26.2 52.4 B1 NOTES: 1. LEADER AND TRAILER TAPE 160 MIN. TOP TAPE TRAILER C So 390 MIN. TOP TAPE C COMPONENT W 160 MIN. TAIL PART (EMPTY) 230 MIN. LEADER PART (EMPTY) 2. PEELING OFF FORCE OF THE TOP TAPE: 20-80gf. (PEELING DIRECTION AS SHOWN IN FOLLOWING FIGURE) B V SECTION V-V 12.00 PULL OUT DIRECTION 0.20 ±0.05 3. PACKAGING STANDARD IS AS PER EIA-481. 4. TAPE & REEL QUANTITY: EMBOSSED TYPE A & B = 1000PCS/REEL EMBOSSED TYPE B1 = 900PCS/REEL 5. THE TAPE IS TREATED FOR ANTI-STATIC. ℄ R0.75 CUSTOMER PULL OUT DIRECTION THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS MM 4 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL 9 P1 RELEASE DATE 2018/10/11 8 ± ± 1 PLACE DOCUMENT STATUS INCH ± 3 PLACES ± FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 CURRENT REV DESC: MIGRATED TO ECTR GENERAL TOLERANCES (UNLESS SPECIFIED) PART NO. 87263-**9* (CKTS 18 TO 40) DOUBLE SPROCKET HOLE T/REEL - TYPE B A ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:17:35 7 B PEEL OFF DIRECTION 15° MAX. 6 5 4 EC NO: 605777 DRWN: RMV02 CHK'D: GJEEVANSURES APPR: ISHWARG INITIAL REVISION: DRWN: JDK APPR: MLONG THIRD ANGLE PROJECTION 3 2018/02/02 2018/10/11 2018/10/11 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/01/11 2010/03/19 SD-87263-XX2X MATERIAL NUMBER DRAWING SERIES A3-SIZE 87263 2 A MGRID, B/ENTRY RECEPT. 2.80MM HT. W/LOC. PEGS W/CAP, SMT SEE TABLE PSD 001 J12 SHEET NUMBER CUSTOMER GENERAL MARKET 1 3 OF 4 9 7 8 6 5 4 3 2 1 PART WITHOUT CKT CAP IN T&R SIZE 9 87263-3686 T/REEL TYPE B1 ⌀1.50 +0.10 0.00 E 36 Bo Ko Ao 36.40 5.00 6.60 4.00 ±0.10 2.00 ±0.20 A E 1.75 ±0.10 9.00 ±0.20 F ±0.30 9.50 ±0.20 Bo +0.20 -0.10 So ±0.10 B W ±0.30 B D D 16.00 ±0.10 A Ko +0.20 -0.10 SECTION A-A Ao +0.20 -0.10 C C 3.40 ±0.20 3.20 ±0.20 SECTION B-B B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO ECTR GENERAL TOLERANCES (UNLESS SPECIFIED) A MM 4 PLACES ± 3 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/10/11 8 ± ± 1 PLACE FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 INCH ± ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:17:35 7 6 5 4 EC NO: 605777 DRWN: RMV02 CHK'D: GJEEVANSURES APPR: ISHWARG INITIAL REVISION: DRWN: JDK APPR: MLONG THIRD ANGLE PROJECTION 3 2018/02/02 2018/10/11 2018/10/11 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/01/11 2010/03/19 SD-87263-XX2X MATERIAL NUMBER DRAWING SERIES A3-SIZE 87263 2 A MGRID, B/ENTRY RECEPT. 2.80MM HT. W/LOC. PEGS W/CAP, SMT SEE TABLE PSD 001 J12 SHEET NUMBER CUSTOMER GENERAL MARKET 1 4 OF 4