0873401429

9 7 8 5 6 A 3 2 2 . PLATING FINISH: 5 & 7 - 0.05µm-0.25µm GOLD IN CONTACT AREA 1.90µm/75µ" MIN. TIN IN SOLDER TAIL AREA BOTH OVER 1.30µm/50µ" MIN. NICKEL OVERALL 3 & 8 - 0.76µm/30µ" MIN. GOLD IN CONTACT AREA 1.90µm/75µ" MIN. TIN IN SOLDER TAIL AREA BOTH OVER 1.30µm/50µ" MIN. NICKEL OVERALL 4 & 9 - 0.38µm/15µ" MIN. GOLD IN CONTACT AREA 1.90µm/75µ"in MIN. TIN IN SOLDER TAIL AREA BOTH OVER 1.30µm/50µ" MIN. NICKEL OVERALL E 2.00 4.20 1.10 0.50 3 . COPLANARITY OF SOLDER TAIL IS TO BE MEASURED BY RESTING THE PART ON A FLAT GAUGE SURFACE. 4. PRODUCT SPECIFICATION PS-87340 APPLIES. 5. THIS AREA OF PART TO BE HEAT STAKED TO RETAIN CONTACTS. 6. PART IS MATEABLE TO ALL MILLI-GRID HEADERS WITH MINIMUM PIN LENGTHS OF 1.90mm FOR TOP ENTRY. SQ. 0.50 (TYP) B 1 PART NO. IN TUBE NOTES: 1. 12 CIRCUIT SIZE SHOWN FOR ILLUSTRATION ONLY. SEE CHART FOR AVAILABLE PART SIZES. 2.00 D 4 CKT. DIM. B DIM. A SIZE 87340-04** 4 2.00 4.00 87340-06** 6 4.00 6.00 87340-08** 8 6.00 8.00 87340-10** 10 8.00 10.00 87340-12** 12 10.00 12.00 87340-14** 14 12.00 14.00 87340-16** 16 14.00 16.00 87340-18** 18 16.00 18.00 87340-20** 20 18.00 20.00 E D 4.80 MAX 0.80 ±0.13 CONTACT HEIGHT 0.70 2.15 MAX 3 0.30 ⌓ 0.10 C C 0.70 ±0.05 OPTIONAL (2X) 0.35 ±0.05 OPTIONAL (2X) 3.05 B 1.00 TYP (2X) PART NO. LEGEND SOLDER PAD 2.00 TYP 87340 - **** CIRCUIT SIZE PACKAGING & PLATING 2 3 - (TUBE WITH 0.76µm MIN GOLD) 4 - (TUBE WITH 0.38µm MIN GOLD) 5 - (TUBE WITH 0.05-0.25µm GOLD) 7 - (T&R WITH 0.05-0.25µm GOLD) 8 - (T&R WITH 0.76µm MIN GOLD) 9 - (T&R WITH 0.38µm MIN GOLD) B 1 - WITHOUT LOCATING PEGS (HOUSING - BLACK) 2 - WITH LOCATING PEGS (HOUSING - BLACK) 5 - WITHOUT LOCATING PEGS (HOUSING - NATURAL) 6 - WITH LOCATING PEGS (HOUSING - NATURAL) 3.75 B 7.50 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE mm NTS MM 4 PLACES ± OPTIONAL (2X) FOR LOCATING PEG ONLY DOCUMENT STATUS 9 2 PLACES ± 1.00 TYP P1 RELEASE DATE 2018/05/30 8 ± ± 0 PLACES ± ± ANGULAR TOL ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:36:19 7 ± 0.2 ± 1 PLACE RECOMMENDED PCB LAYOUT INCH ± 3 PLACES ± ⌀ 0.80 ±0.05 FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 CURRENT REV DESC: MIGRATED TO ECTR GENERAL TOLERANCES (UNLESS SPECIFIED) 1.75 A DIMENSION UNITS 6 5 4 EC NO: 172635 MGRID 2018/02/20 VLPR II, 2MM DUAL ROW TOP ENTRY RECEPT., SMT 2018/05/25 2018/05/30 PRODUCT CUSTOMER DRAWING DRWN: RMV02 CHK'D: CD APPR: GGA INITIAL REVISION: DRWN: JKACHLI APPR: MLONG THIRD ANGLE PROJECTION 3 DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/07/02 2009/11/24 SD-87340-XX01 MATERIAL NUMBER DRAWING SERIES A3-SIZE 87340 2 SEE TABLE PSD 001 L9 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 3 A 9 7 8 5 6 4 3 2 TYPE A Ko 1 TYPE B 4 Ao E E Ao F F Bo D So W W ±0.30 D 12.00 3.70 CUSTOMER PULL OUT DIRECTION CUSTOMER PULL OUT DIRECTION EMBOSSED CARRIER TAPE WITH DIMENSIONS EMBOSSED CARRIER TAPE WITH DIMENSIONS C C NOTES: 1. LEADER AND TRAILER TAPE 160 MIN. TOP TAPE TRAILER 390 MIN. TOP TAPE B 160 MIN. TAIL PART (EMPTY) B PULL OUT DIRECTION COMPONENT 230 MIN. LEADER PART (EMPTY) 2. PEELING OFF FORCE OF THE TOP TAPE: 20-80gf. (PEELING DIRECTION AS SHOWN IN FOLLOWING FIGURE) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION PEEL OFF DIRECTION 15° MAX. A DIMENSION UNITS SCALE mm NTS GENERAL TOLERANCES (UNLESS SPECIFIED) PULL OUT DIRECTION MM 4 PLACES ± PACKAGING STANDARD IS AS PER EIA-481. 2 PLACES ± DOCUMENT STATUS FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 9 P1 RELEASE DATE 2018/05/30 8 ± 0.2 ± ± ± 0 PLACES ± ± 1 PLACE 4 . NO FIX ORIENTATION OF ASSEMBLY PART IN T&R. 5. TAPE & REEL QUANTITY : TBA INCH ± 3 PLACES ± 3. CURRENT REV DESC: MIGRATED TO ECTR ANGULAR TOL ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:36:19 7 6 5 4 EC NO: 172635 MGRID 2018/02/20 VLPR II, 2MM DUAL ROW TOP ENTRY RECEPT., SMT 2018/05/25 2018/05/30 PRODUCT CUSTOMER DRAWING DRWN: RMV02 CHK'D: CD APPR: GGA INITIAL REVISION: DRWN: JKACHLI APPR: MLONG THIRD ANGLE PROJECTION 3 DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/07/02 2009/11/24 SD-87340-XX01 MATERIAL NUMBER DRAWING SERIES A3-SIZE 87340 2 SEE TABLE PSD 001 L9 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 3 A 9 7 8 6 5 4 3 2 1 PART NO. PART NO. CKT SIZE Ao IN TUBE TAPE/REEL E Bo F Ko W So 87340-0424 87340-0429 04 6.60 4.50 7.50 16.00 2.85 - 87340-1014 87340-1019 10 6.70 10.40 11.50 24.00 5.30 - 87340-1613 87340-1618 16 6.60 16.30 11.50 24.00 4.40 - 87340-1424 87340-1429 14 6.60 14.40 11.50 24.00 4.40 - 87340-1813 87340-1818 18 6.60 18.40 14.20 32.00 4.40 28.40 87340-1814 87340-1819 18 6.60 18.40 14.20 32.00 4.40 28.40 87340-2024 87340-2029 20 6.60 20.30 20.20 44.00 5.40 40.40 D E D COVER TAPE EMBOSSED CARRIER C C CUSTOMER PULL OUT DIRECTION REEL TAPE AND REEL ASSEMBLY SHOWN IS FOR ILLUSTRATION ONLY. B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO ECTR GENERAL TOLERANCES (UNLESS SPECIFIED) A MM 4 PLACES ± 3 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/05/30 8 ± ± 1 PLACE FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 INCH ± ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:36:19 7 6 5 4 EC NO: 172635 MGRID 2018/02/20 VLPR II, 2MM DUAL ROW TOP ENTRY RECEPT., SMT 2018/05/25 2018/05/30 PRODUCT CUSTOMER DRAWING DRWN: RMV02 CHK'D: CD APPR: GGA INITIAL REVISION: DRWN: JKACHLI APPR: MLONG THIRD ANGLE PROJECTION 3 DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/07/02 2009/11/24 SD-87340-XX01 MATERIAL NUMBER DRAWING SERIES A3-SIZE 87340 2 SEE TABLE PSD 001 L9 SHEET NUMBER CUSTOMER GENERAL MARKET 1 3 OF 3 A