0873814037

9 7 8 5 6 4 3 2 DIM A 1.00 DIM B 0.80 TYP. 0.50 TYP. E 1.50 1.10 3.50 4.20 2.00 7.00 ⌀ 0.80 ±0.05 SEE NOTE 6 2.00 ±0.08 TYP. 2.00 RECOMENDED PCB LAYOUT 0.70 ±0.05 2.10 ±0.10 1.20 F4 CONTACT POINT 4.00 ±0.15 C 4 ⌓ 0.10 0.35 ±0.15 0.35 ±0.05 �2X� SEE NOTE 6 B PART No. CKT. SIZE DIM A DIM B 87381-06** 6 4.00 6.00 87381-08** 8 6.00 8.00 87381-10** 10 8.00 10.00 87381-12** 12 10.00 12.00 87381-14** 14 12.00 14.00 87381-16** 16 14.00 16.00 87381-18** 18 16.00 18.00 87381-20** 20 18.00 20.00 87381-22** 22 20.00 22.00 87381-24** 24 22.00 24.00 87381-26** 26 24.00 26.00 87381-28** 28 26.00 28.00 87381-30** 30 28.00 30.00 87381-32** 32 30.00 32.00 87381-34** 34 32.00 34.00 87381-36** 36 34.00 36.00 87381-38** 38 36.00 38.00 87381-40** 40 38.00 40.00 87381-42** 42 40.00 42.00 87381-44** 44 42.00 44.00 87381-46** 46 44.00 46.00 87381-48** 48 46.00 48.00 87381-50** 50 48.00 50.00 6.20 0.50 ±0.10 SEE NOTE 6 1. PLATING FINISH: GOLD PLATING OPTION IN CONTACT AREA (SEE SHT 2) TIN IN SOLDER TAIL AREA BOTH OVER 1.27µm MIN NICKEL OVERALL 2. 12 CKT SIZE SHOWN FOR ILLUSTRATION ONLY. SEE CHART FOR ALL AVAILABLE PART SIZES. 3. PRODUCT SPECIFICATION PS-87380 APPLIES. 4 COPLANARITY OF SOLDER TAIL IS TO BE MEASURED BY RESTING THE PART ON A FLAT GAUGE SURFACE +0.05 UPWARDS AND -0.05 DOWNWARDS. 5. OTHER PLATING OPTIONS AVAILABLE . PLEASE CONTACT FACTORY 6. PEG AND PCB HOLE OPTIONAL. SEE PART LEGEND FOR PART CONFIGURATION 7. PARTS SHALL BE PACKED IN MOISTURE BARRIER BAG. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS MM 4 PLACES ± PART IN TUBE 9 RELEASE DATE 2019/07/09 8 INCH ± 3 PLACES ± ± 0.2 ± ± ± 0 PLACES ± ± ANGULAR TOL P1 CURRENT REV DESC: ADDED BTB DIST. GENERAL TOLERANCES (UNLESS SPECIFIED) �10.40� 1 PLACE DOCUMENT STATUS C �9.40� 2 PLACES ± FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 D B NOTES: A E SOLDER PAD DIM A D 1 ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 06:47:10 7 6 5 4 EC NO: 619055 DRWN: HK02 CHK'D: NMANE02 APPR: MRAMAKRISHNA INITIAL REVISION: DRWN: TAY APPR: RWONG THIRD ANGLE PROJECTION 3 2019/05/14 2019/07/09 2019/07/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1993/01/21 1993/01/27 SD-87381-XXXX MATERIAL NUMBER DRAWING SERIES A3-SIZE 87381 2 A MGRID 4MM HT., WITH LOC. PEG SEE CHART PSD 001 F5 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 3 9 7 8 6 5 4 3 2 1 PLATING OPTION E PEG OPTION 0.05µm MIN GOLD 1.90µm MIN TIN NO YES **37 **38 0.76µm MIN GOLD 0.38µm MIN GOLD 1.27µm MIN TIN 1.27µm MIN TIN **07 **17 E **08 **18 PART NUMBER LEGEND 87381 - ** ** D D PLATING AND PEG OPTION (SEE TABLE) CIRCUIT SIZE C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: ADDED BTB DIST. GENERAL TOLERANCES (UNLESS SPECIFIED) A MM 4 PLACES ± 3 PLACES ± 2 PLACES ± ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2019/07/09 8 ± ± 1 PLACE FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2017/10/06 INCH ± ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 06:47:10 7 6 5 4 EC NO: 619055 DRWN: HK02 CHK'D: NMANE02 APPR: MRAMAKRISHNA INITIAL REVISION: DRWN: TAY APPR: RWONG THIRD ANGLE PROJECTION 3 2019/05/14 2019/07/09 2019/07/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1993/01/21 1993/01/27 SD-87381-XXXX MATERIAL NUMBER DRAWING SERIES A3-SIZE 87381 2 A MGRID 4MM HT., WITH LOC. PEG SEE CHART PSD 001 F5 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 3 10 9 7 8 5 6 4 3 2 1 F F BOARD TO BOARD (BTB) DISTANCE RECEPTACLE MATES WITH(HEADER) BTB DISTANCE PICTORIAL VIEW E 87831 E � 7.01 � 7.01 87381 � 8.21 � D 87832 D 8.21 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: ADDED BTB DIST. GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± 3 PLACES ± 2 PLACES ± A ± 0.2 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 10 P1 RELEASE DATE 9 2019/07/09 ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 06:47:10 8 ± ± 1 PLACE FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 INCH ± 7 6 5 4 EC NO: 619055 DRWN: HK02 CHK'D: NMANE02 APPR: MRAMAKRISHNA INITIAL REVISION: DRWN: DRWN BY APPR: APPR BY THIRD ANGLE PROJECTION 2019/05/14 2019/07/09 2019/07/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER XXXX/XX/XX XXXX/XX/XX DRAWING SERIES A3-SIZE 87381 3 MGRID 4MM HT., WITH LOC. PEG SD-87381-XXXX MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 F5 SHEET NUMBER 3 OF 3 1 A