1054550101

PRODUCT SPECIFICATION TITLE 1.0 SCOPE This Product Specification covers the requirement of USB type C receptacle. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER Product name: USB type C receptacle Series number: 105448, 105385, 105387, 105450,105454，105455，204711，205714 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See sales drawing 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS Industry Standard Reference: Universal Serial Bus Type-C Cable and Connector Specification, Revision 1.2, Test compliant reference: Universal Serial Bus Type-C Connectors and Cable Assemblies Compliance Document Test standard reference: EIA-364 series. See sales drawings and other sections of this specification for the relevant reference documents. In cases where the specification differs from the drawings, the sales drawings take precedence. 4.0 RATINGS 4.1 VOLTAGE 30 Volts DC/AC Max. 4.2 CURRENT 5 Amps MAX. for total VBUS pins ( Pin A4, A9, B4, B9), 1.25 Amps MAX. for Vconn (B5 of plug) with return path through the corresponding GND pins(Pin A1, A12, B1, B12). 0.25 Amps MIN. for all other contact. 4.3 TEMPERATURE Operating: - 30°C to + 85°C Storage: - 45°C to + 85°C REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 1 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.1.1 Low Level Contact Resistance(LLCR) The solder tail to the solder tail or cable 40 milliohms Max initial. attachment point of the plug, including any Is not Exceed 50 milliohms internal contacts and paddle card.Measure after environmental test. at 20 mV (max) open circuit at 100 mA. Per EIA-364-23 5.1.2 Insulation Resistance Mate connectors, apply 100 VDC between adjacent terminal or ground. 100Megohms Min. Per EIA-364-21 Dielectric 5.1.3 Withstanding Voltage 5.1.4 Temperature Rise Differential 5.1.5 Impedance (Informative) 5.1.6 Mate connectors, and measure the temperature rise of contact when the maximum rate current is passed per section 4.2. Per EIA-364-70,Method 2 Temperature change 30°C Max at the outside surface of the shell receptacle. The mated connector impedance target is specified to minimize reflection from the connector. Cross Talk (Informative) Differential-toCommon-Mode 5.1.9 Conversion (Informative) For D+/D-: 75~105Ω, 40ps rise time (20%-80%) For SS pairs: 85±9Ω, 40ps rise time(20%~80%) Vertices: (100MHz, -0.25dB), (2.5GHz, -0.35dB), (5GHz, -0.45dB), (10GHz, 0.75dB), (15GHz, -1.85dB) Differential Insertion Mated connector, measure by Network Loss (Informative) Analyzer. Differential Return 5.1.7 Loss(Informative) 5.1.8 Mate connectors, apply 100 VAC(RMS) for No breakdown 1 minute between adjacent terminal or ground. Per EIA-364-20 ,Method B. Vertices: (100MHz, -20dB), (5GHz, 20dB), (10GHz, -13dB), (15GHz, -6dB) Mated connector, measure by Network Analyzer. Vertices that define the Mated connector, measure the differential DDNEXT limit: Near-End and Far-End Crosstalk between (100MHz, -40dB), (5GHz, Supper Speed Pairs. 40dB), (10GHz, -36dB), (15GHz, -30dB) Mated connector, Measure the differential Crosstalk Between D+/D- and Super Speed Pairs Vertices that define the DDNEXT and DDFEXT limit: (100MHz, -40dB), (5GHz, 40dB), (7.5GHz, -36dB) Mated connector pairs vertices: (100 MHz, -30 dB), (6 GHz, -30 dB), and (10 GHz, -25 dB). REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 2 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.2.1 Mate connector, at maximum rate 12.5mm/min. Per EIA-364-13 Insertion force: 5~20N Un-mate connector, at maximum rate 12.5mm/min. Per EIA-364-13 Within the range of 8 N to 20 N, measured after a preconditioning of five insertion/extraction cycles. After an additional twenty-five insertion/extraction cycles, the extraction force shall be measured again and the extraction force shall be within: a) 33 % of the initial reading, and b) within the range of 8 N to 20 N. The extraction force shall be within the range of 6 N to 20 N after 10,000 insertion/extraction cycles. Perform 4 plug/unplug cycles. Cycle rate of 500+/-50cycles per hour in test Group4 Within the range of 8 N to 20 N. Initial reading Perform 25 plug/unplug cycles. Cycle rate of 500+/-50cycles per hour in test Group4 Within: a).33% off the initial reading, and b).8 N to 20 N. Perform 2468 plug/unplug cycles. Rotate the receptacle or plug 180° and perform 2,500 plug/unplug cycles. Rotate the receptacle or plug 180° and perform 2,500 plug/unplug cycles. Rotate the receptacle or plug 180 and perform 2,500 plug/unplug cycles. Cycle rate of 500+/-50 cycles per hour (total of 10,000 plug/unplug cycles, flipping every 2,500 cycles) in test No mechanical damage Contact resistance is not exceed +50 milliohms; Dielectric Withstanding Voltage meet 100 VAC; Extraction force: 6N~20N. 5.2.2 5.2.3 Insertion force Extraction force Durability (10000 Cycles) Group4, Per EIA-364-09 5.2.4 Durability EIA-364-09 (preconditioning) Perform 50 unplug/plug cycles. 5.2.5 Reseating Manually mate and unmate the connector for 3 cycles. Rate: 5 cycles/min. max. EIA 364-09 5.2.6 Plug and Receptacle: Subject the No discontinuities greater than 1 4-Axis Continuity mating interface to the moments microsecond duration in any of the Test defined in Section 8 for at least 10 four orientations tested. seconds. No physical damage No evidence of physical damage. REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 3 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.3 ENVIRONMENTAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.3.1 Solderability Unmated connector. Dip solder tails into the molten solder(held at 240-250°C) up to for in immersion duration 6s. Per EIA 364-52, Solder coverage: 95% Min. No mechanical damage or change to appearance. 5.3.2 Resistance to soldering Heat Peak temperature in reflow:255°C (– 0/+5°C) .Pb-free reflow profile refer to No mechanical damage or Section 7.0 ,two cycles. change to appearance s. Per EIA 364-56 5.3.3 Mate connectors And expose to 40±2°C, relative humidity 90 to 95 % for 96 hours. Cyclic Upon completion of the exposure Temperature and period, the test specimens shall be Humidity conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. Per EIA-364-31 5.3.4 5.3.5 Thermal Shock Vibration No mechanical damage. Contact resistance is not exceed 50 milliohms. Insulation resistance not less than 100 Megaohms. Dielectric strength must meet Item 5.1.2 Test Condition I 10 Cycles –55 degree C and +85degree C. Mate Connector Per EIA 364-32, No mechanical damage. Contact resistance is not Exceed 50 milliohms. Mate connectors, and subject to the following vibration conditions, Random vibration , 15 minutes in each of 3 mutually perpendicular axes,10~2000Hz, 0.02 g2/Hz 20 minutes per plane Per EIA-364-28 condition VII, Test letter D No mechanical damage Contact resistance is not exceed 50 milliohms. Signal discontinuity < 1 s. REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 4 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION ITEM DESCRIPTI ON 5.3.6 Cycle the connector between 15°C±3°C and 85°C±3°C, as measured on the part. Ramps should be a minimum of 2°C per Thermal minute, and dwell times should insure Disturbance that contacts reach temperature extreme for a minimum of 5minutes. No humidity control. 10 cycles total. 5.3.7 Vibration TEST CONDITION REQUIREMENT Mate connectors, and subject to the following vibration conditions, Random vibration 3 mutually perpendicular axes, 10~2000Hz, 0.02g2/Hz 20 minutes per plane Per EIA-364-28 condition VII, Test letter D No mechanical damage Contact resistance is not exceed 50 milliohms. Signal discontinuity < 1 s. Mate connectors, and subject to the mixed flowing gas conditions. 1) expose 1/2 of the specimens unmated for 2/3 of the test duration; 2) mate each specimen to the same plug that it was mated to during temperature life (preconditioning); and, 3) expose for the remainder of the test duration. 30u’gold or Gold flash& 30u’Pd-Nickel plating for 7 days.15u’gold for 5 days. Gold flash for 3 days. Note: Per EIA-364-65 class II condition A No mechanical damage and visible corrosion. Contact resistance not exceed 50 milliohms. 5.3.8 Mixed flowing gas test 5.3.9 Mate connectors, and subject to the Temperature conditions of 105°C for 120 hours. life Per EIA-364-17 condition A 5.3.10 Contact resistance is not exceed 50 milliohms. No mechanical damage and visible corrosion. Contact resistance is not exceed 50 milliohms. Temperature life Mate connectors, and subject to the (precondition conditions of 105°C for 72 hours. ) Per EIA-364-17 condition A No mechanical damage and visible corrosion. Contact resistance is not exceed 50 milliohms. The meaning of text “mechanical damage” in the table above is: a. No significant corrosion at contact area b. No adhesion problem of plating c. No blistering of plating d. No flaking of plating REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 5 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION e. No loosen parts f. No cracks on any parts 5.0 TEST GROUPINGS Note: All test specimens (except group 5) shall pass the reflow process for 2 times. Test Item 5.1.1 5.2.4 5.1.2 5.1.3 5.3.10 Description Low level contact resistance Durability (preconditioning) Insulation resistance Dielectric withstanding voltage Temperature life (Preconditioning) 5.3.9 Temperature life 5.3.4 Thermal shock 5.3.6 5.3.3 5.3.8 Group1 Group2 Group3 Group4 1,4,6 1,4,6,8 1,4,6 1,4,6,8 ,10 2 2 2 2 Group5 3 3 3 3 Thermal disturbance Cyclic temperature & humidity Mixed flowing gas 7 5 5 Reseating 5.1.4 Temperature rise 5.2.1 Insertion force 4 5.2.2 Extraction force 5,7,9 5.2.6 5 5 7 9 1 Durability (4 cycles) Durability (25cycles) Durability (9968 cycles) 3 6 8 Solderability 1 resistance to soldering Heat testing 4-Axis Continuity Test Sample Quantity 1 1 5 5 5 5 5 5 5 REVISION: ECR/ECN INFORMATION: TITLE: C USB C type receptacle DATE: 2019/06/14 PS-105448-001 5 5 SHEET No. EC No: DOCUMENT NUMBER: Group9 1,11 5.2.5 5.3.2 Group8 12 Vibration 5.3.1 Group7 2,10 5.3.7 5.2.3 Group6 CREATED / REVISED BY: RZHANG CHECKED BY: 6 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 6.0 PACKAGING Parts shall be packaged to protect against damage during handling, transit and storage. The parts shall be carried in tape & reels inside boxes. For details refer to packaging spec. 7.0 Recommended reflow profile Pb-free reflow profile requirements for soldering heat resistance Parameter Reference Specification Average temperature gradient in preheating 2.5°C/s Soak time tsoak 2-3 minutes Time above 217°C t1 Max 60 s Time above 230°C t2 Max 50 s Time above 255°C±5°C t3 Min 5 s Peak temperature in reflow Tpeak 255°C (–0/+5°C) Temperature gradient in cooling Max -5°C/s REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 7 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION Not to scale, for reference only Temperature Tpeak peak T33 T22 T11 tsoak t3 t3 t2 Time t2 t1 Reflow profile for soldering heat resistance testing Notes: 1: Reflow soldering profile for solderability testing and soldering heat resistance testing 2: Temperature indicated refers to the PCB surface temperature at soldertail area. 3: Connector can withstand up to 2 reflow cycles with a cool-down to room temperature inbetween. 4: Actual reflow profile also depends on equipment, solder paste, PCB thickness, and other components on the board. Please consult your solder paste & reflow equipment manufacturer for their recommendations to adopt a suitable process. 8.0 4-Axis Continuity Test The USB Type-C connector family shall be tested for continuity under stress using a test fixture, Detailed information refer to USB Type-C industry standard and its compliance document. REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 8 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION Figure D-1 Example of 4-AxIs Continuity Test Fixture Plugs shall be supplied with a representative overmold or mounted on a 2-layer printed circuit board (PCB) between 0.8 mm and 1.0 mm thickness as applicable. A USB Type-C receptacle shall be mounted on a 2-layer PCB between 0.8 mm and 1.0 mm thickness. The PCB shall be clamped on three sides of the receptacle no further than 5 mm away from the receptacle outline. The receptacle PCB shall initially be placed in a horizontal plane, and a perpendicular moment shall be applied to the plug with a 5 mm ball tipped probe for a period of at least 10 seconds at a distance of 15 mm from the mating edge of the receptacle shell in a downward direction, perpendicular to the axis of insertion. See Table D-1 for the force and moment to be applied. Receptacle configuration with respect to mounting surface Force at 15 mm from receptacle shell mating edge (N) Moment with respect to receptacle shell mating edge (Nm) Right angle 20 0.30 Vertical 8 0.12 Table D-1 Force and Moment Requirements REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 9 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION The continuity across each contact shall be measured throughout the application of the tensile force. Each non-ground contact shall also be tested to confirm that it does not short to the shell during the stresses. The PCB shall then be rotated 90 degrees such that the cable is still inserted horizontally and the tensile force in Table D-1 shall be applied again in the downward direction and continuity measured as before. This test is repeated for 180 degree and 270 degree rotations. Passing parts shall not exhibit any discontinuities or shorting to the shell greater than 1 μs duration in any of the four orientations. One method for measuring the continuity through the contacts is to short all the wires at the end of the cable pigtail and apply a voltage through a pull-up to each of VBUS, USB D+, USB D−, SBU, CC, and USB SuperSpeed pins, with the GND pins connected to ground. Alternate methods are allowed to verify continuity through all pins. Appendices: The signal integrity of the mated Connector is normative in the USB type C specification. And Type C compliance document tell that receptacle compliance testing includes dimensional inspection, mechanical, environmental and DC electrical tests but it does not cover signal integrity and shielding effectiveness. A receptacle is considered part of the host/device from signal integrity and shielding effectiveness perspective. So the test group of signal integrity is not shown in this specification but only show its requirement. REVISION: ECR/ECN INFORMATION: TITLE: C SHEET No. EC No: USB C type receptacle DATE: 2019/06/14 DOCUMENT NUMBER: PS-105448-001 CREATED / REVISED BY: RZHANG CHECKED BY: 10 of 10 APPROVED BY: AYIN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC