11-03-0044

Extractor Tool for Mini-Fit ™ Series Terminals Extractor Tool (HT60630B) Application Tooling Specification Sheet Order No. 11-03-0044 FEATURES  This Extractor Tool is for the removal of Mini-Fit Jr. Crimped Terminals Series from their housings. SCOPE Products: Mini-Fit Jr.™, Mini-Fit HCS™, and Mini-Fit Plus HCS™, Male, and Female Crimp Terminals 14-30 AWG and 2.00mm (.079") Pitch Board-In Male Crimp Terminal, 24-28 AWG. Terminal Series No. 5556 5558 30490 44476 44478 44485 45750 46012 46018 Terminal Order No. 39-00-0038 39-00-0065 39-00-0089 39-00-0112 39-00-0141 39-00-0167 39-00-0179 39-00-0194 39-00-0208 39-00-0406 39-00-0436 39-00-0040 39-00-0067 39-00-0095 39-00-0126 39-00-0223 39-00-0433 30490-1002 44476-1111 44476-9901 44478-1111 44478-3111 44478-9901 44485-1211 44485-2311 44485-3411 45750-1111 45750-4111 46012-1141 46012-3241 46018-1541 Doc No: ATS-011030044 Revision: K 39-00-0039 39-00-0066 39-00-0090 39-00-0113 39-00-0142 39-00-0168 39-00-0180 39-00-0195 39-00-0211 39-00-0410 39-00-0440 39-00-0041 39-00-0068 39-00-0096 39-00-0127 39-00-0224 39-00-0437 30490-1012 44476-1112 44476-9902 44478-1112 44478-3112 44478-9902 44485-1212 44485-2312 44485-3412 45750-1112 45750-4112 46012-1142 46012-3242 46018-1542 39-00-0046 39-00-0073 39-00-0093 39-00-0114 39-00-0153 39-00-0169 39-00-0181 39-00-0198 39-00-0212 39-00-0419 39-00-0441 39-00-0048 39-00-0075 39-00-0099 39-00-0130 39-00-0411 39-00-0449 30490-2002 44476-1211 44476-9903 44478-1221 44478-3121 44478-9903 44485-1311 44485-2411 44485-5211 45750-1211 45750-4211 46012-1241 46012-3251 46018-2541 Release Date: 03-01-05 Revision Date: 10-15-14 39-00-0047 39-00-0074 39-00-0094 39-00-0115 39-00-0154 39-00-0170 39-00-0182 39-00-0200 39-00-0213 39-00-0425 39-00-0447 39-00-0049 39-00-0076 39-00-0100 39-00-0131 39-00-0420 39-00-0450 30490-2012 44476-1212 44476-9904 44478-1122 44478-3122 44478-9904 44485-1312 44485-2412 44485-5212 45750-1212 45750-4212 46012-1242 46012-3252 46018-2542 39-00-0055 39-00-0077 39-00-0108 39-00-0116 39-00-0157 39-00-0173 39-00-0183 39-00-0201 39-00-0214 39-00-0428 39-00-0448 39-00-0053 39-00-0081 39-00-0120 39-00-0147 39-00-0426 40-13-0853 30490-9802 44476-3111 44476-9905 44478-1211 44478-3211 44478-9905 44485-1411 44485-3211 44485-5311 45750-3111 39-00-0056 39-00-0078 39-00-0109 39-00-0117 39-00-0158 39-00-0174 39-00-0184 39-00-0204 39-00-0217 39-00-0429 40-13-0851 39-00-0054 39-00-0082 39-00-0121 39-00-0148 39-00-0430 40-13-0854 30490-9902 44476-3112 44476-9906 44478-1212 44478-3212 44478-9906 44485-1412 44485-3212 44485-5312 45750-3112 39-00-0059 39-00-0079 39-00-0110 39-00-0118 39-00-0163 39-00-0175 39-00-0185 39-00-0205 39-00-0218 39-00-0434 40-13-0852 39-00-0061 39-00-0083 39-00-0124 39-00-0219 39-00-0431 39-00-0060 39-00-0080 39-00-0111 39-00-0119 39-00-0164 39-00-0176 39-00-0186 39-00-0207 39-00-0405 39-00-0435 44476-3211 44476-9907 44478-1121 44478-3221 44478-9907 44485-2211 44485-3311 44485-5411 45750-3211 44476-3212 44476-9908 44478-1222 44478-3222 44478-9908 44485-2212 44485-3312 44485-5412 45750-3212 39-00-0062 39-00-0084 39-00-0125 39-00-0220 39-00-0432 46012-3141 46012-3142 46012-3151 46012-3152 46018-3541 46018-3542 UNCONTROLLED COPY Page 1 of 3 Extractor Tool for Mini-Fit ™ Series Terminals Terminal Series No. 46083 46098 5378 Terminal Order No. 46083-1111 46083-2111 46083-3111 46098-1541 39-00-0029 46083-1112 46083-2112 46083-3112 46098-1542 39-00-0030 46083-1121 46083-2121 46083-3121 46098-2541 46083-1122 46083-2122 46083-3122 46098-2542 46083-1211 46083-2211 46083-3211 46098-3541 46083-1212 46083-1221 46083-1222 46083-2212 46083-2221 46083-2222 46083-3212 46083-3221 46083-3222 46098-3542 OPERATION: 1. Insert the extractor tool into the housing as shown in Figure 1. 2. Use the slots located on the inside of the housing to guide the extraction tool blades into the housing until contact is made with terminal. TERMINAL 3. Continue to insert the tool always checking to see that the blades of extraction tool are on the outside of the contact as shown in Figure 2. HOUSING 4. Continue to insert extraction tool into housing until the locking tangs have snapped out of their locked position. If the SLOTS FOR EXTRACTOR terminal locking tabs are still not totally TOOL depressed, hold on tight to the wire and push it towards the extractor tool, this will completely depress the locking tabs. See Figure 1 Figure 2. 5. Gently pull the terminal by the wire, out from the housing. LOCKING TABS DEPRESSED PULL WIRE AND TERMINAL EXTRACTOR TOOL EXTRACTOR TOOL FINGERS MUST BE ON THE OUTSIDE OF THE TERMINAL CONTACTS TERMINAL Figure 2 (HOUSING REMOVED) Terminal Series No. 44478-**2* 44476 EXTRACTOR TOOL Terminal and Housing Application Chart Used with Housing Series No. Uses Extractor Tool 44157 No. 63813-1200 only for these Terminal and Housing Combinations. 44156 NOTE: When a terminal is removed in this manner the locking tangs are damaged and the terminal is not reusable. Doc No: ATS-011030044 Revision: K Release Date: 03-01-05 Revision Date: 10-15-14 UNCONTROLLED COPY Page 2 of 3 Extractor Tool for Mini-Fit ™ Series Terminals LOCKING TAB LIFTED UP For 5378 Terminal Series: Individual terminals may be extracted from the housing using this Tool. 1. Hold the housing with the locking tab facing up. Bend the wire down and insert one of the blades of the extractor tool into the housing under the locking tab. See Figure 3. 2. Hold the wire against the extractor tool and gently pull the terminal by the wire and the extractor tool at the same time out from the housing in the direction shown. 3. Molex does not offer repair parts for Extractor Tools due to the inexpensive nature of these tools. Figure 3 PULL WIRE AND TERMINAL OUT EXTRACTOR TOOL CAUTION: This extractor tool should be used to extract the terminal only. Using it for unintended purposes may cause injury or damage to parts. Be careful not to deform the end of the terminal. CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Visit our Web site at http://www.molex.com Doc No: ATS-011030044 Revision: K Release Date: 03-01-05 Revision Date: 10-15-14 UNCONTROLLED COPY Page 3 of 3