11030043

HT60923A Extractor Tool Extractor Tool Application Tooling Specification Sheet Order No. 11-03-0043 Engineering No. HT60923A FEATURES This tool is designed to extract many different terminals from various plug and receptacle housings. See chart below. SCOPE Products: Terminal Series No. Description 43030 Micro-Fit 3.0™ Crimp Terminal 20-24 AWG 43031 44372 45773 45807 46235 50011 50031 50058 50061 50079 50080 50125 Micro-Fit 3.0™ High Force 20-24 AWG Micro-Fit 3.0™ Lubed Female 20-30 AWG Micro-Fit Plus 3.0™ 18 AWG Micro-Fit 3.0™ Crimp Terminal 20-24 AWG 2.0mm (.079") Low Profile Receptacle Terminal 24-34 AWG 1.25mm (.049") Pitch PicoBlade™ 26-32 AWG 1.25mm (.049") Pitch Board-In Crimp Terminal 28-32 AWG 1.25mm (.049") Pitch PicoBlade™ Crimp Terminal 26-28 AWG Doc No: ATS-011030043 Revision: S Housings Series No. 43025 43645 44133 43020 43640 44300 43025 43645 44133 43025 43695 44133 43025 43645 44133 46623 43025 43645 44133 51004 51049 51004 51049 51021 51022 51021 51022 51047 Terminal Order No. 43030-0001 43030-0007 43030-0051 43030-0059 43031-0001 43031-0007 43031-0016 430310053 43030-0002 43030-0008 43030-0052 43030-0080 43031-0002 43031-0008 43031-0017 43031-0057 43030-0003 43030-0009 43030-0053 43030-0081 43031-0003 43031-0009 43031-0018 43031-0059 43030-0004 43030-0010 43030-0056 43030-1001 43031-0004 43031-0010 43031-0019 43031-0102 43030-0005 43030-0006 43030-0011 43030-0012 43030-0057 43030-0058 43031-0005 43031-0011 43031-0051 43031-0103 43031-0006 43031-0012 430310052 43031-0106 44372-0002 45773-0001 45773-0002 45773-0003 45773-0004 45773-0005 45773-0006 45773-0053 45807-0003 45807-0038 46235-0001 46235-0002 46235-0003 46235-0004 46235-5001 46235-5002 46235-5004 46235-5003 50011-8000 50011-8100 39-00-0422 50031-8000 50031-8100 50058-8000 50058-8099 50058-8100 50058-8200 50058-8300 50058-8400 50058-8500 50061-8000 50061-8018 50061-8028 50061-8099 50061-8100 50061-8118 50061-8128 50079-8000 50079-8053 50079-8099 50079-8100 50079-8153 39-00-0413 39-00-0414 50080-8000 50080-8100 50125-8000 50125-8100 Release Date: 02-02-95 Revision Date: 03-24-17 UNCONTROLLED COPY Page 1 of 3 HT60923A Extractor Tool Terminal Series No. 50133 50200 50212 Description 1.25mm (.049") Pitch PicoBlade™ 28-32 AWG 2.0mm (.079") Low Profile 22-32 AWG Micro-Latch™ 2.00mm (.079") Pitch 24-30 AWG 2.00mm (.079") Pitch 22-26 AWG 50372 50420 560085 4.00mm (.157") Pitch OBD-II Wire-to-Wire DuraClik™ Crimp Terminal, Female, 22-26 AWG Housings Series No. 51047 51004 51049 5109 51065 51090 5109 51065 51090 51115 51116 502351 Terminal Order No. 50133-8000 50133-8100 50200-8000 50200-8100 50212-8000 50212-8100 50212-8200 50212-8300 39-00-0424 50372-8000 50372-8100 50420-8000 50420-8100 50420-8200 560085-0101 HOUSING Note: All individual terminals may be extracted from the housing using this tool. LOCKING TANGS PUSHED IN OPERATION: For 43030, 43031, 44372, 45807 and 46235 Terminal Series: 1. Insert the tip of the tool on either side of the terminal until it stops. See EXTRACTOR Figure 1. Rotate tool clockwise and then counterclockwise TOOL approximately 25° to 30° in each direction, once or twice. 2. Repeat steps 1 and 2 on the opposite side of terminal. 3. Pull on the wire, and remove the terminal from the housing. HOUSING See Figure 2. TERMINAL Figure 1 PULL OUT TERMINAL AND WIRE Note: When a terminal is removed in this manner, the locking tangs are damaged, and the terminal is not reusable. For 50011, 50031, 50058, 50061, 50079, 50080, 50125, 50133, 50200, 50212 and 50372, and 560085 Terminal Series: 1. Hold the housing with the locking tang facing up. Bend the wire down, and insert the tip of the tool into the housing under the locking tang. See Figure 3. LOCKING TANG EXTRACTOR TOOL TIP OF TOOL INSERTED ON THE SIDE OF TERMINAL EXTRACTOR TOOL PUSH UP ON THE LOCKING TANG LOCKING TANGS PUSHED IN Figure 2 EXTRACTOR TOOL IN SLOT BEND WIRE DOWN Doc No: ATS-011030043 Revision: S BEND WIRE DOWN Figure 3 Release Date: 02-02-95 Revision Date: 03-24-17 UNCONTROLLED COPY Page 2 of 3 HT60923A Extractor Tool 2. Hold the wire against the extractor tool, and pull out the wire and the extractor tool at the same time. See Figure 4. EXTRATOR TOOL Note: When reusing the housing, remember to bend back the locking tang when inserting another terminal. For 50420 Terminal Series: 1. Push the terminal forward in the direction of the arrow before using the WIRE extractor tool. Figure 4 2. Insert the tip of the extractor tool on an angle above the terminal into the slot on the top of the connector housing. 3. While rotating the extraction tool down, bend the terminal locking tang down, and push the terminal back through the connector slot. Make sure that the terminated wire is pulled out at the same time. See Figure 5. LOCKING TAB OF HOUSING TERMINAL HOUSING EXTRACTOR TOOL WIRE LOCKING TAB PUSHED UP EXTRACTOR TOOL Figure 5 CAUTION: This extractor tool should be used to extract the terminal only. Using it for unintended purposes may cause injury or damage to parts. Be careful not to deform the end of the terminal. CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling. Molex does not offer repair parts for extractor tools due to the inexpensive nature of these tools. Application Tooling Support Phone: +1-402-458-TOOL (8665) E-Mail: applicationtooling@molex.com Website: www.molex.com/applicationtooling Doc No: ATS-011030043 Revision: S Release Date: 02-02-95 Revision Date: 03-24-17 UNCONTROLLED COPY Page 3 of 3