1110401054

20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M LABEL TEXT ORIENTATION 18.35 ±0.10 (2X) L LABEL TEXT ORIENTATION L P1 P2 SEE DETAIL 1 K K LENGTH (SEE TABLE) LABEL TEXT ORIENTATION 8.5 ±0.1 (2X) LABEL TEXT ORIENTATION J J 50 ±10 50 ±10 H H LABEL TEXT ORIENTATION LABEL TEXT ORIENTATION 16.4 ±0.1 (2X) (PCB WIDTH) SEE SHEET 3 FOR LABEL DETAIL (FOR CABLES UNDER 2 METERS LABEL ON ONE END ONLY) G G 11.6 REF 30 AWG ASSEMBLY F F 28 AWG ASSEMBLY 13.0 REF E E PCB VIEWING HOLES D 13.8 REF 26-24 AWG ASSEMBLY D DETAIL1 SCALE 4:1 SEE SHEET 3 FOR P/N TABLE C B A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C NOTES: 1. CABLE DISTANCE DEPENDS ON WIRE GAUGE, DATA RATE, AND HOST BOARD DRIVER CAPABILITIES 2. MATERIALS: BACKSHELLS - ZINC DIE CAST WITH BRIGHT NICKEL PLATING DELATCH - STAINLESS STEEL WITH OVERMOLDED NYLON PCB - FR4 RIVETS - STAINLESS STEEL 3. IMPEDANCE - 100 OHMS DIFFERENTIAL 4. RoHS COMPLIANT, NO EXEMPTIONS DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/06/02 17 SCALE mm 2:1 CURRENT REV DESC: OBSOLETE PART NUMBER ASPER PCN#506884 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:45:03 16 DIMENSION UNITS 15 14 13 12 11 10 9 8 7 QSFP+ COPPER PATCH CABLE ASSEMBLY CABLE ASSEMBLY EC NO: 662770 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: SCHANNARAYAN APPR: ARAYBURN THIRD ANGLE PROJECTION 2021/04/19 2021/06/02 2021/06/02 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/08/22 2017/09/06 DRAWING 5 1110400001 MATERIAL NUMBER SERIES D-SIZE 111040 6 B GENERAL MARKET 3 AA1 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 1 OF 3 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PAD 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 L K J H G F E LEGEND: ---- = THRU LINES ---> = TRANSMIT TO RECEIVE ON HIGH SPEED CIRCUITS C = COMMON GROUND CONNECTION NC = NOT CONNECTED ◻ = CONNECTION TO A DEVICE ON THE PCB WIRING DIAGRAM P1 END P2 END PAD SIGNAL SIGNAL ---20 GND (TX) GND (RX) ---> TX2n 21 RX2n ---> TX2p 22 RX2p ---23 GND (TX) GND (RX) TX4n ---> RX4n 24 TX4p ---> RX4p 25 ---26 GND (TX) GND (RX) ModPrsL 27 ModSelL ◻ ◻ ResetL IntL 28 ◻ ◻ VccRx VccTx 29 ◻ ◻ ◻ NC 30 Vcc1 SCL ◻ ◻ LPmode 31 SDA ---32 GND (RX) GND (TX)