1300950234

6 5 CATALOG NUMBER D 4 CABLE RANGE MATERIAL NUMBER 3 LENGTH "M" 2 BREAK STRENGTH* (LBS/N) LENGTH "B" 1 UL LISTED CSA APPROVED PRODUCT SELECTION NUMBER 36101 1300950225 .75-.99 / 19.1-25.1 13.00±1.50 / 330.2±38.1 7.00±1.00 / 177.8±25.4 3000 / 13345 36102 1300950227 1.00-1.24 / 25.4-31.5 16.00±2.00 / 406.4±50.8 8.00±1.00 / 203.2±25.4 4200 / 18683 36103 1300950229 1.25-1.49 / 31.8-37.8 17.00±2.00 / 431.8±50.8 8.00±1.00 / 203.2±25.4 5500 / 24465 36104 1300950230 1.50-1.74 / 38.1-44.2 18.00±2.00 / 457.2±50.8 9.00±1.00 / 228.6±25.4 7400 / 32917 12.00±1.00 / 304.8±25.4 16000 / 71172 SCK300-1 12.00±1.00 / 304.8±25.4 16000 / 71172 SCK350-1 36108 1300950234 3.00-3.49 / 76.2-88.6 22.00±2.50 / 558.8±63.5 36109 1300950235 3.50-3.99 / 88.9-101.3 23.00±2.50 / 584.2±63.5 SCK075-1 Y E S N O D SCK100-1 SCK125-1 SCK150-1 * TO DETERMINE RECOMMENDED WORKING LOAD, DIVIDE BREAK STRENGTH BY 5. C C 5 DOUBLE WEAVE CLOSED MESH 1 LENGTH "B" B B LENGTH "M" (WITHOUT SIZING ROD) 2 3 4 FUNCTIONAL SYMBOLS ITEM 1 2 A DESCRIPTION WIRE MESH CRIMP CONNECTOR MATERIAL =0 GALVANIZED STEEL =0 ALUMINUM =0 3 FERRULE ALUMINUM 4 BALE WIRE STAINLESS STEEL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE INCH/MM NTS GENERAL TOLERANCES (UNLESS SPECIFIED) mm LABEL ± ---- 3 PLACES ± ---- ± 0.005 DIVISIONAL SYMBOLS 2 PLACES ± 0.13 1 PLACE DOCUMENT STATUS FORMAT: ACAD-tb-prod-A REVISION: C DATE: 2022/10/04 6 MYLAR P1 ± 0.25 ANGULAR TOL ± RELEASE DATE 2023/02/16 5 INCH 4 PLACES ± ---- 0 PLACES ± ---- 5 ± 0.01 ± 0.02 ± ---0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:36:35 4 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#510808 PULLING GRIPS EC NO: 736640 DRWN: SUGEEB CHK'D: LIKITV APPR: GGA INITIAL REVISION: DRWN: HRUIZ01 APPR: JFMURPHY THIRD ANGLE PROJECTION 3 HEAVY DUTY-SLACK EYE DOUBLE WEAVE CLOSED MESH 2022/12/21 2023/02/14 2023/02/16 DOCUMENT NUMBER 2014/09/05 2016/09/12 DRAWING SERIES A-SIZE 130095 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION SD-130095-113 MATERIAL NUMBER SEE TABLE 2 PSD 001 CUSTOMER A1 SHEET NUMBER GENERAL MARKET 1 1 OF 1