1703901026

12 11 10 9 8 7 5 6 4 3 B 0.80 MIN "KEEP-OUT ZONE" SEE NOTE 12 2 1 1.25 MIN 1.90 H ⌀0.39 ±0.05 (12 HOLES PER COLUMN) ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A "D" G 20.15 14.85 "A" F 2.65 E G F GROUND HOLE REF SEE NOTE 9 SIGNAL HOLES REF PIN A1 VERTICAL RECEPTACLE HOLE PATTERN (CONNECTOR SIDE) H STACK HEIGHT "C" H ⌖ ⌀0.10 11X 1.35 E PIN A1 D C B A D NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30 µINCH MIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE MATTE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. SEE CHARTS FOR PACKAGING SPECIFICATIONS. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-170335-0001 FOR THE MATING HEADERS. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. MARKING: LOCATED APPROXIMATELY AS SHOWN PART NUMBER & DATE CODE 10. GROUND PATHS ARE NOT DISCRETE CIRCUITS WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 11. PART NUMBER 170390-1030 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 12. THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE CONNECTOR INSERTION AND REPAIR ON THE PCB. THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2018/04/02 10 C B SYMBOLS = 0 = 0 = 0 9 8 7 6 MM 3:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 C SCALE ANGULAR TOL = 0 13:39:33 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 173912 DRWN: DVARVARA CHK'D: TELO APPR: TELO INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2018/03/28 2018/04/02 2018/04/02 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/04/03 2013/04/05 DRAWING SERIES C-SIZE 170390 4 IMPACT 4-PAIR 85-OHM UNGUIDED MEZZANINE SALES DRAWING 3 SD-170390-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A5 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 10 9 7 8 5 6 4 3 2 1 PART NUMBER CHART G MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIRS DIM "A" MAX DIM "B" 170390-1008 8 32 15.1 13.3 170390-1000 10 40 18.9 17.1 170390-1002 12 48 22.7 20.9 170390-1007 14 56 26.5 24.7 170390-1006 16 64 30.3 28.5 170390-1009 18 72 34.1 32.3 DIM "C" DIM "D" PACKAGING SPEC 15.36 19.41 PK-70873-4001 18mm STACK HEIGHT (DIM H) H H G 0.35 OFFSET BETWEEN MALE AND FEMALE HOLE PATTERNS # OF COLUMNS DIM "A" MAX # OF DIFF PAIRS DIM "B" DIM "C" DIM "D" PACKAGING SPEC F 8 32 15.1 13.3 170390-1020 10 40 18.9 17.1 170390-1022 12 48 22.7 20.9 170390-1027 14 56 26.5 24.7 170390-1026 16 64 30.3 28.5 170390-1029 18 72 34.1 32.3 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIRS DIM "A" MAX DIM "B" 170390-1038 8 32 15.1 13.3 170390-1030 10 40 18.9 17.1 170390-1032 12 48 22.7 20.9 22.36 19.41 PK-70873-4002 E D DIM "C" 34.36 C 170390-1037 14 56 26.5 24.7 170390-1036 16 64 30.3 28.5 170390-1039 18 72 34.1 32.3 DIM "D" 20.65 PACKAGING SPEC PK-70873-0044 F E 37mm STACK HEIGHT (DIM H) 170390-1028 25mm STACK HEIGHT (DIM H) MATERIAL NUMBER D C PART NUMBER LOGIC 170390-103* B B MODULE AND TAIL PLATING TYPE 1 = UNGUIDED, MATTE TIN KEY ORIENTATION 0 = UNGUIDED STACK HEIGHT (H) 0 = 18mm 2 = 25mm 3 = 37mm A SYMBOLS # OF COLUMNS 0 = 10 COL 2 = 12 COL 6 = 16 COL 7 = 14 COL 8 = 8 COL 9 = 18 COL = 0 = 0 = 0 DOCUMENT STATUS 12 P1 RELEASE DATE 11 2018/04/02 10 C 9 8 7 6 MM 3:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 13:39:33 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 173912 DRWN: DVARVARA CHK'D: TELO APPR: TELO INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2018/03/28 2018/04/02 2018/04/02 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/04/03 2013/04/05 DRAWING SERIES C-SIZE 170390 4 IMPACT 4-PAIR 85-OHM UNGUIDED MEZZANINE SALES DRAWING 3 SD-170390-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A5 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A