1703905008

12 11 10 9 8 7 5 6 4 3 2 1 ⌖ ⌀0.10 H B ⌀0.39 ±0.05 8.90 0.80 (12 HOLES PER COLUMN) 5.10 ⌖ ⌀0.10 1.90 ⌀4.38 ±0.04 11X 1.35 D H UNPLATED HOLE ⌖ ⌀0.10 4.67 G ⌀2.45 ±0.04 UNPLATED HOLES 2X KEY SHOWN IN POSITION A 20.15 G 14.85 4.45 A ROW A F F 2.30 SEE NOTE 12 2.65 PIN A1 GROUND HOLE REF KEEP-OUT ZONE VERTICAL RECEPTACLE HOLE PATTERN (CONNECTOR SIDE) H STACK HEIGHT C SIGNAL HOLES REF E E PIN A1 D C B A D NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30 µINCH MIN GOLD IN CONTACT AREA. SELECTIVE MATTE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. SEE CHART FOR PACKAGING SPECIFICATIONS. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-170335-0003 FOR THE MATING HEADERS 8. REFER TO MOLEX ROUTING PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. GROUND PATHS ARE NOT DISCRETE WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 10. PART NUMBER 170390-5130 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 11. FOR SCREW PART NUMBER AND FUNCTIONAL BOARD THICKNESS REFER TO CHART ON SHEET 2. IN ORDER TO ACCOMMODATE ALTERNATE BOARD THICKNESSES PLEASE CONTACT MOLEX. 12. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2021/02/04 10 C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM NTS GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:13:18 9 8 CURRENT REV DESC: CORRECTED TYPO IN NOTE 7 7 6 5 EC NO: 629583 DRWN: SKRISHNAMU01 CHK'D: CWANG25 APPR: STTAN INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2019/12/11 2019/12/23 2021/02/04 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/04/04 2013/04/05 DRAWING SERIES C-SIZE 170390 4 IMPACT 4-PAIR 85-OHM RIGHT GUIDE MEZZANINE SALES DRAWING 3 SD-170390-0003 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A5 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 10 9 7 8 5 6 4 3 2 1 PART NUMBER CHART # OF COLUMNS # OF DIFF PAIRS DIM "A" MAX DIM "B" DIM "C" DIM "D" PACKAGING SPEC FUNCTIONAL BOARD THICKNESS SCREW P/N H G 170390-5*03 6 24 19.0 9.5 170390-5*08 8 32 22.8 13.3 170390-5*00 10 40 26.6 17.1 170390-5*02 12 48 30.4 20.9 170390-5*07 14 56 34.2 24.7 170390-5*06 16 64 38.0 28.5 170390-5*09 18 72 41.8 32.3 # OF COLUMNS # OF DIFF PAIRS DIM "A" MAX DIM "B" 170390-5*28 8 32 22.8 13.3 170390-5*20 10 40 26.6 17.1 170390-5*22 12 48 30.4 20.9 170390-5*27 14 56 34.2 24.7 170390-5*26 16 64 38.0 28.5 170390-5*29 18 72 41.8 32.3 DIM "C" PK-70873-4001 19.41 DIM "D" PACKAGING SPEC 73726-0005 2.0mm TO 3.0mm FUNCTIONAL BOARD THICKNESS SCREW P/N F 22.36 PK-70873-4002 19.41 73726-0000 1.0mm TO 5.0mm H G 0.35 OFFSET BETWEEN FEMALE AND MALE HOLE PATTERNS 25mm STACK HEIGHT (DIM H) MATERIAL NUMBER 15.36 18mm STACK HEIGHT (DIM H) MATERIAL NUMBER F BACKPLANE (SERIES 170335) VERTICAL FEMALE E E # OF COLUMNS # OF DIFF PAIRS DIM "A" MAX DIM "B" 170390-5*38 8 32 22.8 13.3 170390-5*30 10 40 26.6 17.1 170390-5*32 12 48 30.4 20.9 170390-5*37 14 56 34.2 24.7 170390-5*36 16 64 38.0 28.5 170390-5*39 18 72 41.8 32.3 DIM "C" 34.36 DIM "D" PACKAGING SPEC PK-70873-0044 20.65 FUNCTIONAL BOARD THICKNESS SCREW P/N 73726-0000 1.0mm TO 5.0mm 37mm STACK HEIGHT (DIM H) D MATERIAL NUMBER D C C PART NUMBER LOGIC 170390-**** B B MODULE AND TAIL PLATING TYPE 5 = GUIDE RIGHT, MATTE TIN # OF COLUMNS 3 = 6 COL 8 = 8 COL 0 = 10 COL 2 = 12 COL 7 = 14 COL 6 = 16 COL 9 = 18 COL KEY ORIENTATION 0 = NO KEY 1=A 5=E 2=B 6=F 3=C 7=G 4=D 8=H THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2021/02/04 10 SCALE MM NTS ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:13:18 9 8 CURRENT REV DESC: CORRECTED TYPO IN NOTE 7 GENERAL TOLERANCES (UNLESS SPECIFIED) STACK HEIGHT (H) 0 = 18mm 2 = 25mm 3 = 37mm A DIMENSION UNITS 7 6 5 EC NO: 629583 DRWN: SKRISHNAMU01 CHK'D: CWANG25 APPR: STTAN INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2019/12/11 2019/12/23 2021/02/04 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/04/04 2013/04/05 DRAWING SERIES C-SIZE 170390 4 IMPACT 4-PAIR 85-OHM RIGHT GUIDE MEZZANINE SALES DRAWING 3 SD-170390-0003 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A5 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A