1704751128

12 11 10 9 7 8 5 6 4 3 B 0.95 2 1 0.95 A 1.35 �ADD FOR END WALL� H B PIN A1 1.35 �ADD FOR END WALL� 1.90 H 1.90 Z 2.95 ROW A ROW B ROW C ROW D ROW E ROW F ROW G ROW H ROW J ROW K ROW L ROW M ROW N ROW O ROW P SIGNAL HOLES REF. G 1.35 14X 18.90 24.8 +0.2 -0.5 GROUND HOLES REF. 18.90 24.8 1.35 14X F Z F �2.95� KEEP OUT ZONE E TAIL LENGTH PIN LENGTH 1.4 P ±0.20 11.95 E ⌖ ⌀0.10 SEE PART NUMBER CHART AND PART NUMBER LOGIC (15 HOLES PER COLUMN) UNGUIDED BACKPLANE HOLE PATTERN (CONNECTOR SIDE) SEE NOTE 9 D G D NOTCH DESIGNATES ROW A 2.64 SECTION Z-Z NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µ INCH MIN GOLD IN CONTACT AREA. SELECTIVE MATTE TIN PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PARTS PACKAGED PER PK-70873-7702. 6. SEE SHEETS 2 & 3 FOR PART NUMBERS AND BOARD RELATIONSHIPS. 7. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 8. MIMINUM CIRCUIT BOARD THICKNESS: 1.0mm. 9. "THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMMODATE CONNECTOR INSERTION AND REPAIR ON THE PC BOARD. THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. WHEN LAYING OUT A PC BOARD FOR CONNECTORS STACKED TOGETHER, USE THE 1.9mm PROGRESSION." FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 01.12.2017 10 9 8 2017/10/24 2017/11/30 2017/12/01 7 6 5 DATE ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2010/05/18 DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE JLAURX APPR BY IMPACT 5-PAIR 85-OHM UNGUIDED BACKPLANE SALES ASSEMBLY DRAWING 2010/05/18 JBINGHAM 4 PLACES CHK'D BY C3 12:29:04 DRWN BY ANGULAR TOL ± 2.0 ° REV RELEASE STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 4:1 (UNLESS SPECIFIED) MIGRATED TO NX A B 168852 NVELUSAMY CD GGA B C EC NO: DRWN: CHK'D: APPR: C PRODUCT CUSTOMER DRAWING 2013/05/21 THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 170475 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-170475-0001 3 CUSTOMER 2 PSD 1 OF 3 001 1 A 12 11 10 9 7 8 6 5 4 3 2 1 PART NUMBER TABLE H H MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B 170475-182* 8 40 17.9 13.30 170475-112* 10 50 21.7 17.10 170475-122* 12 60 25.5 20.90 170475-162* 16 80 33.1 28.50 DUAL END WALL OPTION DUAL END WALL OPTION G G MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B F 170475-181* 8 40 16.5 13.30 170475-111* 10 50 20.3 17.10 170475-121* 12 60 24.1 20.90 170475-161* 16 80 31.7 28.50 LEFT END WALL OPTION LEFT END WALL OPTION F E E MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B D 170475-183* 8 40 16.5 13.30 170475-113* 10 50 20.3 17.10 170475-123* 12 60 24.1 20.90 170475-163* 16 80 31.7 28.50 RIGHT END WALL OPTION RIGHT END WALL OPTION D MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B C 170475-180* 8 40 15.1 13.30 170475-110* 10 50 18.9 17.10 170475-120* 12 60 22.7 20.90 170475-160* 16 80 30.3 28.50 OPEN WALL OPTION C OPEN WALL OPTION B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 01.12.2017 C3 12:29:04 10 9 8 7 6 5 REV RELEASE STATUS DATE ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2010/05/18 DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE JLAURX APPR BY IMPACT 5-PAIR 85-OHM UNGUIDED BACKPLANE SALES ASSEMBLY DRAWING 2010/05/18 JBINGHAM 4 PLACES CHK'D BY EC NO: DRWN: CHK'D: APPR: A DRWN BY ANGULAR TOL ± 2.0 ° 168852 NVELUSAMY CD GGA MIGRATED TO NX 2017/10/24 2017/11/30 2017/12/01 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 2:1 (UNLESS SPECIFIED) PRODUCT CUSTOMER DRAWING 2013/05/21 THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 170475 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-170475-0001 3 CUSTOMER 2 PSD 2 OF 3 001 1 A 12 11 10 9 8 7 5 6 4 3 2 1 PART NUMBER LOGIC 170475- H **** P=PIN LENGTH 3 = 4.50 (SHORT COMPLIANT, 0.46±0.05 PTH) 4 = 4.90 (SHORT COMPLIANT, 0.46±0.05 PTH) 5 = 5.50 (SHORT COMPLIANT, 0.46±0.05 PTH) 6 = 4.50 (MICRO COMPLIANT, 0.39±0.05 PTH) 7 = 4.90 (MICRO COMPLIANT, 0.39±0.05 PTH) 8 = 5.50 (MICRO COMPLIANT, 0.39±0.05 PTH) MODULE TYPE 1 = UNGUIDED, MATTE TIN IMPACT 5 PAIR BOARD RELATIONSHIPS G # OF COLUMNS 1 = 10 COL 2 = 12 COL 6 = 16 COL 8 = 8 COL ENDWALL OPTIONS 0 = OPEN ENDS 1 = LEFT END WALL 2 = DUAL END WALL 3 = RIGHT END WALL DCARD PCB F H G F BP ROW A 24.8 3.0 BPLANE PCB E E DC HOLE COLUMN (COLUMN 10 REF.) D D DCARD ROW A 14.0 BP ROW A 11.95 DCARD PCB C C DCARD ROW A 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS BPLANE PCB B B BP HOLE COLUMN (COLUMN 10 REF.) FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 01.12.2017 C3 12:29:04 10 9 8 7 6 5 REV RELEASE STATUS DATE ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 4 2010/05/18 DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE JLAURX APPR BY IMPACT 5-PAIR 85-OHM UNGUIDED BACKPLANE SALES ASSEMBLY DRAWING 2010/05/18 JBINGHAM 4 PLACES CHK'D BY EC NO: DRWN: CHK'D: APPR: A DRWN BY ANGULAR TOL ± 2.0 ° 168852 NVELUSAMY CD GGA MIGRATED TO NX 2017/10/24 2017/11/30 2017/12/01 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL TOLERANCES MM 3:1 (UNLESS SPECIFIED) PRODUCT CUSTOMER DRAWING 2013/05/21 THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 170475 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-170475-0001 3 CUSTOMER 2 PSD 3 OF 3 001 1 A