1705401026

12 11 10 9 7 8 5 6 4 3 2 1 1.00 MINIMUM BOARD THICKNESS 25.4 1.2 (TAIL LENGTH) H 24.8 3.80 H SEE NOTE 10 25.90 22.95 G G SEE NOTE 12 PIN A1 11.36 F F B 0.84 SIGNAL HOLES REFERENCE A 1.06 1.90 GROUND HOLE REFERENCE SEE NOTE 9 BACKPLANE REFERENCE BP ROW A E KEEP-OUT ZONE E �2.1� 27.1 25.90 ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A 22.95 D 1.35 17X C 14.00 (FULLY MATED) PIN A1 1.70 MAXIMUM D ⌖ ⌀0.10 C ⌀ PTH 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS (SEE TABLE) (18 HOLES PER COLUMN) SEE NOTE 3 BACKPLANE REFERENCE B A BP PIN A1 NOTES: 1. MATERIALS: HOUSING - LCP (LIQUID CRYSTAL POLYMER), GLASS FILLED, UL94V-0. TERMIANLS - HIGH PERFORMANCE COPPER ALLOY. 2. FINISH: 30 MICROINCHES MINIMUM GOLD IN CONTACT AREA; SELECTIVE MATTE TIN ON PCB TAILS; NICKEL UNDERPLATE OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-589. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-170535-0001 AND RSD-170532-**** FOR THE MATING HEADERS. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. GROUND PATHS ARE NOT DISCRETE CIRCUITS WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 10. PART NUMBER 170540-1020 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 11. MINIMUM BOARD THICKNESS IS 1.00mm FOR COMPLIANT PIN FUNCTIONALITY. 12. MARKING: LOCATED APPROXIMATELY AS SHOWN, PART NUMBER AND DATE CODE. DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) SYMBOLS = 0 = 0 = 0 DOCUMENT STATUS 12 P1 RELEASE DATE 11 2018/08/28 10 17:05:04 C 9 8 7 6 SCALE mm 3:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: ADD 14 COL OPTIONS GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 B 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 603057 DRWN: DMORGAN CHK'D: TELO APPR: TELO INITIAL REVISION: DRWN: KBENES APPR: TELO THIRD ANGLE PROJECTION 2018/04/09 2018/08/28 2018/08/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/08/17 2012/08/23 DRAWING SERIES C-SIZE 170540 4 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL UNGUIDED SALES DRAWING 3 SD-170540-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D SHEET NUMBER 1 OF 2 1 A 12 11 10 9 7 8 5 6 4 3 2 1 H H MATERIAL NUMBER 1705401008 1705401010 1705401014 1705401016 1705401038 1705401020 1705401024 1705401026 G NUMBER OF COLUMNS 8 10 14 16 8 10 14 16 NUMBER OF DIFF PAIR 48 60 84 96 48 60 84 96 DIMNEISON A MAXIMUM 15.20 19.00 26.60 30.40 15.20 19.00 26.60 30.40 DIMENSION B 13.30 17.10 24.70 28.50 13.30 17.10 24.70 28.50 PTH Ø 0.46±0.05 G 0.39±0.05 F F 170540- 1 0 * * NUMBER OF COLUMNS MODULE & TAIL PLATING TYPE 1 = UNGUIDED, LEAD-FREE 08 = 8 COLUMN 0.46 PTH 10 = 10 COLUMN 0.46 PTH 14 = 14 COLUMN 0.46 PTH 16 = 16 COLUMN 0.46 PTH E 38 = 20 = 24 = 26 = E 8 COLUMN 0.39 PTH 10 COLUMN 0.39 PTH 14 COLUMN 0.39 PTH 16 COLUMN 0.39 PTH D D C C B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2018/08/28 10 17:05:04 C 9 8 7 6 mm 1:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: ADD 14 COL OPTIONS GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 603057 DRWN: DMORGAN CHK'D: TELO APPR: TELO INITIAL REVISION: DRWN: KBENES APPR: TELO THIRD ANGLE PROJECTION 2018/04/09 2018/08/28 2018/08/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/08/17 2012/08/23 DRAWING SERIES C-SIZE 170540 4 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL UNGUIDED SALES DRAWING 3 SD-170540-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D SHEET NUMBER 2 OF 2 1 A 12 10 11 9 7 8 5 6 4 3 2 1 1.00 MIN. BOARD THICKNESS H H 25.4 SEE NOTE 10 1.2 (TAIL LENGTH) 3.80 24.8 G G 22.95 25.90 PIN A1 F F SIGNAL HOLES REF 11.36 1.06 0.84 GROUND HOLE SEE NOTE 9 A E B BACKPLANE (REF) 1.90 KEEP-OUT ZONE �2.1� ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A BP ROW A 25.90 27.1 D 22.95 REF 1.35 17X PIN A1 B A 1.70 MAX 14.00 (FULLY MATED) C NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 10µIN MIN GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-589. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-170535-0001 AND RSD-170532-XXXX FOR THE MATING HEADERS. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. GROUND PATHS ARE NOT DISCRETE CIRCUITS WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 10. PART NUMBER 170540-1020 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 11. MINIMUM BOARD THICKNESS IS 1.00MM FOR COMPLIANT PIN FUNCTIONALITY. DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: E1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/05/13 10 8 D ⌖ ⌀0.10 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS ⌀PTH C (SEE CHART) (18 HOLES PER COLUMN) SEE NOTE 3. BACKPLANE (REF) BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:05:16 9 E 7 6 5 EC NO: 705090 DRWN: SKANDB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: MKRAUSE APPR: TELO THIRD ANGLE PROJECTION 2021/10/02 2022/02/10 2022/05/13 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/02/09 2015/03/02 SERIES DRAWING C-SIZE 173120 4 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL UNGUIDED SALES DWG MAPS 3 SD-173120-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 1 OF 2 1 A 12 9 7 8 # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" 173120-1008 8 48 15.20 13.30 173120-1010 10 60 19.00 17.10 173120-1016 16 96 30.40 28.50 173120-1038 8 48 15.20 13.30 173120-1020 10 60 19.00 17.10 173120-1026 16 96 30.40 28.50 MATERIAL NUMBER H G 10 11 5 6 4 3 2 1 PTH⌀ H 173120-10** 0.46 ±0.05 MODULE & TAIL PLATING TYPE 1 = UNGUIDED, LEAD-FREE # OF COLUMNS 08 = 8 COL 0.46 PTH 10 = 10 COL 0.46 PTH 16 = 16 COL 0.46 PTH 20 = 10 COL 0.39 PTH 26 = 16 COL 0.39 PTH 38 = 08 COL 0.39 PTH 0.39 ±0.05 G F F E E D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMASTERED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM A 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: E1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/05/13 10 INCH ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:05:16 9 8 7 6 5 EC NO: 705090 DRWN: SKANDB CHK'D: DYARAS APPR: LZENG INITIAL REVISION: DRWN: MKRAUSE APPR: TELO THIRD ANGLE PROJECTION 2021/10/02 2022/02/10 2022/05/13 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/02/09 2015/03/02 SERIES DRAWING C-SIZE 173120 4 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL UNGUIDED SALES DWG MAPS 3 SD-173120-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 2 OF 2 1 A